This table contains the principal configurable
parameters which are used for a particular voice
interface.
Parsed from file act.mib.txt
Company: None
Module: PRESTICOM7-MIB
This table contains the principal configurable
parameters which are used for a particular voice
interface.
Parsed from file CLEARTRAC7-MIB.mib
Module: CLEARTRAC7-MIB
Vendor: Verso Technologies Canada Inc. (previously was 'Presticom Inc.')
Module: CLEARTRAC7-MIB
[Automatically extracted from oidview.com]
ifvceEntry OBJECT-TYPE SYNTAX IfvceEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains the principal configurable parameters which are used for a particular voice interface." INDEX { ifvceIndex } ::= { ifvceTable 1 }
ifvceEntry OBJECT-TYPE SYNTAX IfvceEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains the principal configurable parameters which are used for a particular voice interface." INDEX { ifvceIndex } ::= { ifvceTable 1 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.727.7.2.18.2.1.1 | ifvceIndex | 0 | 0 | A unique value for each voice interface. |
| 1.3.6.1.4.1.727.7.2.18.2.1.2 | ifvceDesc | 0 | 0 | A textual string containing information about a specific interface. |
| 1.3.6.1.4.1.727.7.2.18.2.1.3 | ifvceProtocol | 0 | 0 | Operating protocol for the NetVoice port. Enter ACELP 8 kbs, ACELP 4.8 kbs when you want to use the port for voice/fax transmissi… |
| 1.3.6.1.4.1.727.7.2.18.2.1.4 | ifvceInterface | 0 | 0 | fxs: Used when connecting to a POTS line or fx0 unit. e-and-m: Used when connecting to the trunk side of a PBX. fx0: Used when co… |
| 1.3.6.1.4.1.727.7.2.18.2.1.5 | ifvceRemotePort | 0 | 0 | Specifies the port number on the remote unit for setting up predefined line activation. Select the number of the port connected t… |
| 1.3.6.1.4.1.727.7.2.18.2.1.6 | ifvceActivationType | 0 | 0 | For each cleartrac voice port, voice/fax line activation can be configured according to one of the following activation types. |
| 1.3.6.1.4.1.727.7.2.18.2.1.7 | ifvceRemoteUnit | 0 | 0 | Specifies the unit name of the NetVoice card at the remote site, for setting up predefined line activation. |
| 1.3.6.1.4.1.727.7.2.18.2.1.8 | ifvceHuntGroup | 0 | 0 | When line activation is defined as switched, this parameter permits hunting more than one port to place an incoming call. |
| 1.3.6.1.4.1.727.7.2.18.2.1.9 | ifvceToneDetectRegen-s | 0 | 0 | This parameter specifies the number of seconds during which Tone tones will be detected and regenerated. |
| 1.3.6.1.4.1.727.7.2.18.2.1.10 | ifvcePulseMakeBreak-ms | 0 | 0 | This parameter specifies the duration, in milliseconds, of the contact(or make) for each digit that is dialed using rotary type d… |
| 1.3.6.1.4.1.727.7.2.18.2.1.11 | ifvceToneOn-ms | 0 | 0 | This parameter specifies the duration, in milliseconds, of the tone used to produce a single Tone digit. |
| 1.3.6.1.4.1.727.7.2.18.2.1.12 | ifvceToneOff-ms | 0 | 0 | This parameter specifies the duration, in milliseconds, of the silence between Tone tones in a dial digit string. |
| 1.3.6.1.4.1.727.7.2.18.2.1.13 | ifvceSilenceSuppress | 0 | 0 | This parameter specifies the degree to which periods of silence will be suppressed and reduced during transmission. A higher Sil… |
| 1.3.6.1.4.1.727.7.2.18.2.1.14 | ifvceSignaling | 0 | 0 | The signaling protocol of this port. |
| 1.3.6.1.4.1.727.7.2.18.2.1.16 | ifvceLocalInbound | 0 | 0 | This parameter specifies the local voice level into the port, measured in 1 db increments. ONLY FOR CARDS OTHER THAN DVC |
| 1.3.6.1.4.1.727.7.2.18.2.1.17 | ifvceLocalOutbound | 0 | 0 | This parameter specifies the local voice level out of the port, measured in 1 db increments. ONLY FOR CARDS OTHER THAN DVC |
| 1.3.6.1.4.1.727.7.2.18.2.1.18 | ifvceFaxModemRelay | 0 | 0 | This parameter enables or disables handling of fax or modem calls on this unit's voice channel. |
| 1.3.6.1.4.1.727.7.2.18.2.1.19 | ifvceFxoTimeout-s | 0 | 0 | This parameter determines the maximum amount of time, in seconds, that the local port will wait for a fax transmission to begin. |
| 1.3.6.1.4.1.727.7.2.18.2.1.20 | ifvceTeTimer-s | 0 | 0 | This parameter determines the delay, in seconds, between M-lead and E-lead activation when the starting method is timed e-and-m. |
| 1.3.6.1.4.1.727.7.2.18.2.1.21 | ifvceFwdDigits | 0 | 0 | This parameter specifies which dial digits (if any) should be forwarded to the remote unit. When set to 0, no dial digits are for… |
| 1.3.6.1.4.1.727.7.2.18.2.1.22 | ifvceFwdType | 0 | 0 | This parameter specifies how the dial digits are sent to the remote unit for forwarding to the attached device such as a PBX. It … |
| 1.3.6.1.4.1.727.7.2.18.2.1.23 | ifvceFwdDelay-ms | 0 | 0 | This parameter specifies the length, in milliseconds, of a pause that precedes the forwarded dial digit string. The value entere… |
| 1.3.6.1.4.1.727.7.2.18.2.1.24 | ifvceDelDigits | 0 | 0 | This parameter specifies the number of leading dial digits (if any) that will be deleted from a dial string before it is forward… |
| 1.3.6.1.4.1.727.7.2.18.2.1.25 | ifvceExtNumber | 0 | 0 | This parameter specifies the extension number for the end device attached to this voice port. |
| 1.3.6.1.4.1.727.7.2.18.2.1.27 | ifvceLinkDwnBusy | 0 | 0 | Used by SDM-9400 and V410 VFC03 cards and by the SDM-9350 and V352 voice ports for versions 7.1.0 and higher. Used only for DVC c… |
| 1.3.6.1.4.1.727.7.2.18.2.1.28 | ifvceToneType | 0 | 0 | This parameter specifies the kind of multi-frequency tone that will be detected on this port. |
| 1.3.6.1.4.1.727.7.2.18.2.1.29 | ifvceRate8kx1 | 0 | 0 | This parameter enables fallback to 8 Kbps with single buffering. |
| 1.3.6.1.4.1.727.7.2.18.2.1.30 | ifvceRate8kx2 | 0 | 0 | This parameter enables fallback to 8 Kbps with double buffering. |
| 1.3.6.1.4.1.727.7.2.18.2.1.31 | ifvceRate5k8x1 | 0 | 0 | This parameter enables fallback to 5.8 Kbps with single buffering. |
| 1.3.6.1.4.1.727.7.2.18.2.1.32 | ifvceRate5k8x2 | 0 | 0 | This parameter enables fallback to 5.8 Kbps with double buffering. |
| 1.3.6.1.4.1.727.7.2.18.2.1.33 | ifvceDVCSilenceSuppress | 0 | 0 | This parameter specifies the degree to which periods of silence will be suppressed and reduced during transmission. A higher Sil… |
| 1.3.6.1.4.1.727.7.2.18.2.1.34 | ifvceDVCLocalInbound | 0 | 0 | This parameter specifies the local voice level into the port, measured in 1 db increments. ONLY FOR DVC CARDS |
| 1.3.6.1.4.1.727.7.2.18.2.1.35 | ifvceDVCLocalOutbound | 0 | 0 | This parameter specifies the local voice level out of the port, measured in 1 db increments. ONLY FOR DVC CARDS |
| 1.3.6.1.4.1.727.7.2.18.2.1.36 | ifvceBroadcastDir | 0 | 0 | When line activation is broadcast (Activation Type parameter set to BROADCAST), this parameter is used to specify whether the vo… |
| 1.3.6.1.4.1.727.7.2.18.2.1.37 | ifvceBroadcastPvc | 0 | 0 | This parameter specifies which PVC will be used for transmitting (on the root) or receiving (on leaves) the broadcast frames. |
| 1.3.6.1.4.1.727.7.2.18.2.1.38 | ifvceAnalogLinkDwnBusy | 0 | 0 | Used by SDM-9400 and V410 VFC03 cards and by the SDM-9350 and V352 voice ports for versions 7.0.3 and lower. See ifvceLinkDwnBusy… |
| 1.3.6.1.4.1.727.7.2.18.2.1.39 | ifvceSpeedDialNum | 0 | 0 | Specifies the Speed Dial Number to be dialed when a off-hook occurs on a port configured with Autodial activation type. |
| 1.3.6.1.4.1.727.7.2.18.2.1.40 | ifvceR2ExtendedDigitSrc | 0 | 0 | No longer supported by the NP Agent 7.1.0 and higher |
| 1.3.6.1.4.1.727.7.2.18.2.1.41 | ifvceR2Group2Digit | 0 | 0 | This parameter defines a Group 2 Digit that is output when dialing out. |
| 1.3.6.1.4.1.727.7.2.18.2.1.42 | ifvceR2CompleteDigit | 0 | 0 | This parameter defines the digit that is output when dialing is complete. |
| 1.3.6.1.4.1.727.7.2.18.2.1.43 | ifvceR2BusyDigit | 0 | 0 | This parameter defines the digit that is output to indicate that the destination is busy. |
| 1.3.6.1.4.1.727.7.2.18.2.1.44 | ifvceMaxFaxModemRate | 0 | 0 | This parameter enables or disables handling of fax or modem calls on this unit's voice channel. |
| 1.3.6.1.4.1.727.7.2.18.2.1.45 | ifvceRate8kx3 | 0 | 0 | This parameter enables fallback to 8 Kbps with triple buffering. |
| 1.3.6.1.4.1.727.7.2.18.2.1.46 | ifvceRate6kx1 | 0 | 0 | This parameter enables fallback to 6 Kbps with single buffering. |
| 1.3.6.1.4.1.727.7.2.18.2.1.47 | ifvceRate6kx2 | 0 | 0 | This parameter enables fallback to 6 Kbps with double buffering. |
| 1.3.6.1.4.1.727.7.2.18.2.1.48 | ifvceRate6kx3 | 0 | 0 | This parameter enables fallback to 6 Kbps with triple buffering. |
| 1.3.6.1.4.1.727.7.2.18.2.1.49 | ifvceRate4k8x1 | 0 | 0 | This parameter enables fallback to 4.8 Kbps with single buffering. |
| 1.3.6.1.4.1.727.7.2.18.2.1.50 | ifvceRate4k8x2 | 0 | 0 | This parameter enables fallback to 4.8 Kbps with double buffering. |
| 1.3.6.1.4.1.727.7.2.18.2.1.51 | ifvceDTalkThreshold | 0 | 0 | This parameter specifies the echo cancellation threshold, measured in 1 db increments. |
| 1.3.6.1.4.1.727.7.2.18.2.1.52 | ifvceToneEnergyDetec | 0 | 0 | This parameter controls whether DTMF detection will include the detection of energy as well as tones. In some cases, DTMF detect… |
| 1.3.6.1.4.1.727.7.2.18.2.1.53 | ifvceExtendedDigitSrc | 0 | 0 | Specifies the origin of the extended digits that will be forwarded to the remote unit. Available on a port configured with Auto… |
| 1.3.6.1.4.1.727.7.2.18.2.1.54 | ifvceDtmfOnTime | 0 | 0 | This parameter specifies the DTMF ON duration, in milliseconds, for filtering unwanted DTMF tones during call progress. |
| 1.3.6.1.4.1.727.7.2.18.2.1.55 | ifvceEnableDtmfOnTime | 0 | 0 | This parameter specifies whether the duration of DTMF ON can be used to filter unwanted DTMF tones during call progress. If DTMF… |