MBS - Max. Burst Size (cells) for GCRA#2. 1..1000000
-1 (output only) means no policing
Parsed from file swc.MIB.txt
Company: marconi
Module: SWC-MIB
Vendor: Marconi
Module: SWC-MIB (swc.MIB)
Type: TABULAR
Access: read-write
Syntax: INTEGER
Automatically extracted from www.mibdepot.com
swcVplConfPolicMbs OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "MBS - Max. Burst Size (cells) for GCRA#2. 1..1000000 -1 (output only) means no policing " ::= { swcVplConfEntry 12 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.809.3.2.5.1.50.1.1 | swcVplConfIfIndex | 0 | 0 | The source port. This value for this object is equal to the value of ifIndex from the Interfaces table of MIB II (RFC 1213). |
1.3.6.1.4.1.809.3.2.5.1.50.1.2 | swcVplConfVpi | 0 | 0 | The VPI value of the VPL. |
1.3.6.1.4.1.809.3.2.5.1.50.1.3 | swcVplConfConnIfNdx | 0 | 0 | The cross connected port. This value for this object is equal to the value of ifIndex from the Interfaces table of MIB II (RFC 121… |
1.3.6.1.4.1.809.3.2.5.1.50.1.4 | swcVplConfEndP | 0 | 0 | end point type - end to end, segment, or both. default = end_to_end |
1.3.6.1.4.1.809.3.2.5.1.50.1.5 | swcVplConfAlarmsConf | 0 | 0 | bitmap : bit position as followed: 1 - inhibit alarms - no alarms generation 2 - AIS_RDI cell_type end_to_end. default = cell_type… |
1.3.6.1.4.1.809.3.2.5.1.50.1.6 | swcVplConfPolicTyp | 0 | 0 | Policing Type - default=UBR (no policing) CBR implies act1=03 VBR1 implies act1=03, act2=03 VBR2 implies act1=03, act2=03 VBR3 imp… |
1.3.6.1.4.1.809.3.2.5.1.50.1.7 | swcVplConfPolicAct1 | 0 | 0 | determine the action taken on a non-conforming cell by GCRA#1 according to the list defined below: 00 - no action other than to i… |
1.3.6.1.4.1.809.3.2.5.1.50.1.8 | swcVplConfPolicPcr | 0 | 0 | PCR - Peak Cell Rate (cell/s) for GCRA#1. 1..353207. -1 (output only) means no policing. PCR should be greater than SCR |
1.3.6.1.4.1.809.3.2.5.1.50.1.9 | swcVplConfPolicCdv | 0 | 0 | CDV - Cell Delay Variation (Usec) for GCRA#1. 1..5368709 -1 (output only) means no policing |
1.3.6.1.4.1.809.3.2.5.1.50.1.10 | swcVplConfPolicAct2 | 0 | 0 | determine the action taken on a non-conforming cell by GCRA#2 according to the list defined below: 00 - no action other than to i… |
1.3.6.1.4.1.809.3.2.5.1.50.1.11 | swcVplConfPolicScr | 0 | 0 | SCR - Substained Cell Rate (cell/s) for GCRA#2. 1..353207 -1 (output only) means no policing. SCR value should be smaller than PCR |
1.3.6.1.4.1.809.3.2.5.1.50.1.13 | swcVplConfPMTyp | 0 | 0 | PM Type - end to end , or segment . if endP = both, pmTyp = SEG |
1.3.6.1.4.1.809.3.2.5.1.50.1.14 | swcVplConfPMBlkSnk | 0 | 0 | PM block size Sink - default=1024 |
1.3.6.1.4.1.809.3.2.5.1.50.1.15 | swcVplConfPMActReq | 0 | 0 | PM on remote node: 1 - activate PM on remote node SOURCE (by sending OAM cell). 2 - activate PM on remote node SINK (by sending O… |
1.3.6.1.4.1.809.3.2.5.1.50.1.16 | swcVplConfPMActResp | 0 | 0 | PM Action Response - as listed above . |
1.3.6.1.4.1.809.3.2.5.1.50.1.17 | swcVplConfPMActStat | 0 | 0 | PM Action Status - as listed above . |
1.3.6.1.4.1.809.3.2.5.1.50.1.18 | swcVplConfPMStatus | 0 | 0 | PM activity status: 1 - PM enabled source side. 2 - PM enabled sink side. 3 - PM enabled both sides. 4 - PM disabled. |
1.3.6.1.4.1.809.3.2.5.1.50.1.19 | swcVplConfAlarmState | 0 | 0 | Alarm_state status indications |
1.3.6.1.4.1.809.3.2.5.1.50.1.20 | swcVplConfDefectType | 0 | 0 | Alarm defect type: 0: no defect type. 1: problem detected in atm layer. 2: problem detected in link layer. |
1.3.6.1.4.1.809.3.2.5.1.50.1.21 | swcVplConfDefectLoc | 0 | 0 | Alarm location id |
1.3.6.1.4.1.809.3.2.5.1.50.1.22 | swcVplConfLoopGenAct | 0 | 0 | loop_back generator action code as described below: NONE - no generation of loop_back cell SEND - send loop_back cell. CLEAR - c… |
1.3.6.1.4.1.809.3.2.5.1.50.1.23 | swcVplConfLoopGenTx | 0 | 0 | loop_back generator - number of cells transmitted |
1.3.6.1.4.1.809.3.2.5.1.50.1.24 | swcVplConfLoopGenRx | 0 | 0 | loop_back generator - number of cells received |
1.3.6.1.4.1.809.3.2.5.1.50.1.25 | swcVplConfLoopGenStat | 0 | 0 | loop_back generator status code as described below: IDLE - no generation of loop_back cell in_process - loop_back test is in proc… |
1.3.6.1.4.1.809.3.2.5.1.50.1.26 | swcVplConfLooperCount | 0 | 0 | looper - number of loop_back cells counter |
1.3.6.1.4.1.809.3.2.5.1.50.1.27 | swcVplConfType | 0 | 0 | swcVplConftype |
1.3.6.1.4.1.809.3.2.5.1.50.1.28 | swcVplConfCC | 0 | 0 | Continuity check on local node: 1 - enable CC - source. 2 - disable CC - sink. 3 - enable CC - both (source & sink). 4 - disable CC… |
1.3.6.1.4.1.809.3.2.5.1.50.1.29 | swcVplConfCCActReq | 0 | 0 | Continuity check on remote node: 1 - activate CC on remote node SOURCE (by sending OAM cell). 2 - activate CC on remote node SINK… |
1.3.6.1.4.1.809.3.2.5.1.50.1.30 | swcVplConfCCStatus | 0 | 0 | Continuity check status: 1 - CC enabled source side. 2 - CC enabled sink side. 3 - CC enabled both sides. 4 - CC disabled. |
1.3.6.1.4.1.809.3.2.5.1.50.1.31 | swcVplConfPMBlkSrc | 0 | 0 | PM block size Source - default=1024 |
1.3.6.1.4.1.809.3.2.5.1.50.1.32 | swcVplConfPMReq | 0 | 0 | PM on local node: 1 - enable PM - source. 2 - disable PM - sink. 3 - enable PM - both (source & sink). 4 - disable PM - source. 5 - … |
1.3.6.1.4.1.809.3.2.5.1.50.1.33 | swcVplConfLoopCellTyp | 0 | 0 | loopback cell type: 1 - end to end. 2 - segment. |