An entry in the SWC configuration data table.
Each VPL has an entry in this table associated
with it.
Parsed from file swc.MIB.txt
Company: marconi
Module: SWC-MIB
Vendor: Marconi
Module: SWC-MIB (swc.MIB)
Type: ENTRY
Access: not-accessible
Syntax: SwcVclConfEntry
Automatically extracted from www.mibdepot.com
swcVclConfEntry OBJECT-TYPE SYNTAX SwcVclConfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the SWC configuration data table. Each VPL has an entry in this table associated with it." INDEX { swcVclConfIfIndex, swcVclConfVpi, swcVclConfVci } ::= { swcVclConfTable 1 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.809.3.2.5.1.51.1.1 | swcVclConfIfIndex | 0 | 0 | The source port. This value for this object is equal to the value of ifIndex from the Interfaces table of MIB II (RFC 1213). |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.2 | swcVclConfVpi | 0 | 0 | The VPI value of the VCL. |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.3 | swcVclConfVci | 0 | 0 | The VCI value of the VCL. |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.4 | swcVclConfConnIfNdx | 0 | 0 | The cross connected port. This value for this object is equal to the value of ifIndex from the Interfaces table of MIB II (RFC 121… |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.5 | swcVclConfCallId | 0 | 0 | The SVC call id. |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.6 | swcVclConfEndP | 0 | 0 | end point type - end to end, segment, or both. default = end_to_end |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.7 | swcVclConfAlarmsConf | 0 | 0 | bitmap : bit position as followed: 1 - inhibit alarms - no alarms generation 2 - AIS_RDI cell_type end_to_end. default = cell_type… |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.8 | swcVclConfPolicTyp | 0 | 0 | Policing Type - default=UBR (no policing) CBR implies act1=03 VBR1 implies act1=03, act2=03 VBR2 implies act1=03, act2=03 VBR3 imp… |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.9 | swcVclConfPolicAct1 | 0 | 0 | determine the action taken on a non-conforming cell by GCRA#1 according to the list defined below: 00 - no action other than to i… |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.10 | swcVclConfPolicPcr | 0 | 0 | PCR - Peak Cell Rate (cell/s) for GCRA#1. 1..353207 -1 (output only) means no policing. PCR should be greater than SCR |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.11 | swcVclConfPolicCdv | 0 | 0 | CDV - Cell Delay Variation (Usec) for GCRA#1. 1..5368709 -1 (output only) means no policing |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.12 | swcVclConfPolicAct2 | 0 | 0 | determine the action taken on a non-conforming cell by GCRA#2 according to the list defined below: 00 - no action other than to i… |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.13 | swcVclConfPolicScr | 0 | 0 | SCR - Substained Cell Rate (cell/s) for GCRA#2. 1..353207 -1 (output only) means no policing. SCR value should be smaller than PCR |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.14 | swcVclConfPolicMbs | 0 | 0 | MBS - Max. Burst Size (cells) for GCRA#2. 1..1000000 -1 (output only) means no policing |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.15 | swcVclConfPMTyp | 0 | 0 | PM Type - end to end , or segment. if endP = both, pmTyp = SEG |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.16 | swcVclConfPMBlkSnk | 0 | 0 | PM block size Sink - default=1024 |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.17 | swcVclConfPMActReq | 0 | 0 | PM on remote node: 1 - activate PM on remote node SOURCE (by sending OAM cell). 2 - activate PM on remote node SINK (by sending O… |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.18 | swcVclConfPMActResp | 0 | 0 | PM Action Response - as listed above . |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.19 | swcVclConfPMActStat | 0 | 0 | PM Action Status - as listed above . |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.20 | swcVclConfPMStatus | 0 | 0 | PM activity status: 1 - PM enabled source side. 2 - PM enabled sink side. 3 - PM enabled both sides. 4 - PM disabled. |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.21 | swcVclConfAlarmState | 0 | 0 | alarm state indications |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.22 | swcVclConfDefectType | 0 | 0 | Alarm defect type: 0: no defect type. 1: problem detected in atm layer. 2: problem detected in link layer. |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.23 | swcVclConfDefectLoc | 0 | 0 | Alarm location id |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.24 | swcVclConfLoopGenAct | 0 | 0 | loop_back generator action code as described below: NONE - no generation of loop_back cell SEND - send loop_back cell. CLEAR - cle… |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.25 | swcVclConfLoopGenTx | 0 | 0 | loop_back generator - number of cells transmitted |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.26 | swcVclConfLoopGenRx | 0 | 0 | loop_back generator - number of cells received |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.27 | swcVclConfLoopGenStat | 0 | 0 | loop_back generator status code as described below: IDLE - no generation of loop_back cell in_process - loop_back test is in proc… |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.28 | swcVclConfLooperCount | 0 | 0 | looper - number of loop_back cells counter |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.29 | swcVclConfType | 0 | 0 | swcVclConftype |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.30 | swcVclConfCC | 0 | 0 | Continuity check on local node: 1 - enable CC - source. 2 - disable CC - sink. 3 - enable CC - both (source & sink). 4 - disable CC… |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.31 | swcVclConfCCActReq | 0 | 0 | Continuity check on remote node: 1 - activate CC on remote node SOURCE (by sending OAM cell). 2 - activate CC on remote node SINK… |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.32 | swcVclConfCCStatus | 0 | 0 | Continuity check status: 1 - CC enabled source side. 2 - CC enabled sink side. 3 - CC enabled both sides. 4 - CC disabled. |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.33 | swcVclConfPMBlkSrc | 0 | 0 | PM block size Sink Source - default=1024 |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.34 | swcVclConfPMReq | 0 | 0 | PM on local node: 1 - enable PM - source. 2 - disable PM - sink. 3 - enable PM - both (source & sink). 4 - disable PM - source. 5 - … |
| 1.3.6.1.4.1.809.3.2.5.1.51.1.35 | swcVclConfLoopCellTyp | 0 | 0 | loopback cell type: 1 - end to end. 2 - segment. |