This is a bit-masked attribute which displays events which may cause HSB Reset.
When a bit is '1', the relevant evet may cause HSB Reset.
When a bit is '0', the relevant evet will not cause HSB Reset.
The following are the events:
LSB D0 - Too many packets were discarded from a queue.
D1 - One of the Tx buffers to HSB is full for more than a default period.
D2 - Token has not been available for more than a default period.
D3 - RX Buffer full in one of the ports.
D4 -'1' HSB Reset has been occured , '0'- HSB reset hadn't occured since last
time this MIB has been read.
D5 - '0' - the ram of the relevant port is O.K. (the port is decode in D6-D7) , '1'
The ram is not O.K.
D6- D7 Decode the relevant port that It's ram is not O.K
00 - Port no'0
01 - Port no' 1
10 - Port no' 2
11 - Port no' 3.
Parsed from file APPLIC.MIB.txt
Company: None
Module: APPLIC-MIB
This is a bit-masked attribute which displays events which may cause HSB Reset.
When a bit is '1', the relevant evet may cause HSB Reset.
When a bit is '0', the relevant evet will not cause HSB Reset.
The following are the events:
LSB D0 - Too many packets were discarded from a queue.
D1 - One of the Tx buffers to HSB is full for more than a default period.
D2 - Token has not been available for more than a default period.
D3 - RX Buffer full in one of the ports.
D4 -'1' HSB Reset has been occured , '0'- HSB reset hadn't occured since last
time this MIB has been read.
D5 - '0' - the ram of the relevant port is O.K. (the port is decode in D6-D7) , '1'
The ram is not O.K.
D6- D7 Decode the relevant port that It's ram is not O.K
00 - Port no'0
01 - Port no' 1
10 - Port no' 2
11 - Port no' 3.
Parsed from file APPLIC-MIB.mib
Module: APPLIC-MIB
Vendor: Lannet Company
Module: APPLIC-MIB
[Automatically extracted from oidview.com]
lseGroupHSBMonStatus OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This is a bit-masked attribute which displays events which may cause HSB Reset. When a bit is '1', the relevant evet may cause HSB Reset. When a bit is '0', the relevant evet will not cause HSB Reset. The following are the events: LSB D0 - Too many packets were discarded from a queue. D1 - One of the Tx buffers to HSB is full for more than a default period. D2 - Token has not been available for more than a default period. D3 - RX Buffer full in one of the ports. D4 -'1' HSB Reset has been occured , '0'- HSB reset hadn't occured since last time this MIB has been read. D5 - '0' - the ram of the relevant port is O.K. (the port is decode in D6-D7) , '1' The ram is not O.K. D6- D7 Decode the relevant port that It's ram is not O.K 00 - Port no'0 01 - Port no' 1 10 - Port no' 2 11 - Port no' 3." ::= {lseGroupEntry 24}
lseGroupHSBMonStatus OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This is a bit-masked attribute which displays events which may cause HSB Reset. When a bit is '1', the relevant evet may cause HSB Reset. When a bit is '0', the relevant evet will not cause HSB Reset. The following are the events: LSB D0 - Too many packets were discarded from a queue. D1 - One of the Tx buffers to HSB is full for more than a default period. D2 - Token has not been available for more than a default period. D3 - RX Buffer full in one of the ports. D4 -'1' HSB Reset has been occured , '0'- HSB reset hadn't occured since last time this MIB has been read. D5 - '0' - the ram of the relevant port is O.K. (the port is decode in D6-D7) , '1' The ram is not O.K. D6- D7 Decode the relevant port that It's ram is not O.K 00 - Port no'0 01 - Port no' 1 10 - Port no' 2 11 - Port no' 3." ::= {lseGroupEntry 24}
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.81.19.1.1.1.1 | lseGroupId | 0 | 0 | Slot number in which the group is installed. |
| 1.3.6.1.4.1.81.19.1.1.1.2 | lseGroupFastOpen | 0 | 0 | Setting the value of this attribute to ON activates the port for short idle time when code violation was detected. |
| 1.3.6.1.4.1.81.19.1.1.1.3 | lseGroup10MSqlt | 0 | 0 | Setting the value of this attribute to ON activates the mechanism of detection preamble of 10Mhz. |
| 1.3.6.1.4.1.81.19.1.1.1.4 | lseGroupSmartSqlt | 0 | 0 | Control the mechnism of the input sensitivity of the port. |
| 1.3.6.1.4.1.81.19.1.1.1.5 | lseGroupCParameter | 0 | 0 | Defines the number of consecutive collisions the port waits before it ceases transmitting of 512 bits time toward the station. |
| 1.3.6.1.4.1.81.19.1.1.1.6 | lseGroupIPGJamLength | 0 | 0 | Defines the IPG jam length in Ethernet bit time (100nS) start at 16 bit time in steps of 16, to 112 bit time. For LFE-100, (Fast … |
| 1.3.6.1.4.1.81.19.1.1.1.7 | lseGroupJamLength | 0 | 0 | Defines the Jam Length in time starting from 8 (800micro-seconds) to 120 (12mili-seconds). Each step of 8 is equal 800micro-seco… |
| 1.3.6.1.4.1.81.19.1.1.1.8 | lseGroupDataBlinderLength | 0 | 0 | Defines the Data Blinder Length in Ethernet bit time (100nS) start at 16 bit time in steps of 16 to 112 bit time. For LFE-100, (F… |
| 1.3.6.1.4.1.81.19.1.1.1.9 | lseGroupIPGDataLength | 0 | 0 | Defines the IPG (Inter Packet Gap) length in Ethernet bit time (100nS) starting at 16 bit time in steps of 16 to 112 bit time. Fo… |
| 1.3.6.1.4.1.81.19.1.1.1.10 | lseGroupActiveMonitor | 0 | 0 | This attribute defines the module which is the high-speed bus active monitor. |
| 1.3.6.1.4.1.81.19.1.1.1.11 | lseGroupBackbone12 | 0 | 0 | Port 1 and 2 in the board perform as Backbone link. lse208 - upper cluster is RX only and lower cluster is TX only. lse404 - uppe… |
| 1.3.6.1.4.1.81.19.1.1.1.12 | lseGroupSetDefaults | 0 | 0 | Set all hardware parameters to their default values. This item will always return a value of off(2), since it acts like a toggle… |
| 1.3.6.1.4.1.81.19.1.1.1.13 | lseGroupBackbone34 | 0 | 0 | Port 3 and 4 in the board performed as Backbone link. lse404 - Third port is Rx only and forth port is Tx only. Two remaining por… |
| 1.3.6.1.4.1.81.19.1.1.1.14 | lseGroupBackboneRedun12 | 0 | 0 | Value on(1) of this attribute defines a redundancy (backup) relationship between Backbone port 1 and backbone port 2 on a LANswi… |
| 1.3.6.1.4.1.81.19.1.1.1.15 | lseGroupBackoffFromJam | 0 | 0 | Value on(1) of this attribute defines non-consecutive jam after a collision has occured in LANswitch modules. |
| 1.3.6.1.4.1.81.19.1.1.1.16 | lseGroupCAMClear | 0 | 0 | Value on(1) of this attribute causes the LANSwitch module to clear the CAM tables. |
| 1.3.6.1.4.1.81.19.1.1.1.17 | lseGroupJamPrevent | 0 | 0 | Jam prevent flag. Functionaly, Jam prevent is a back-pressure into the line direction. There are two modes of opration: 1) automat… |
| 1.3.6.1.4.1.81.19.1.1.1.18 | lseGroupNormOpCl | 0 | 0 | Normaly Open/Close flag. When open(1) state is set, the sensor should activate a delay mechanism for the module to operate at Nor… |
| 1.3.6.1.4.1.81.19.1.1.1.19 | lseGroupNormOpDelay | 0 | 0 | When sets to a value greater than 0 (zero) and the MIB item lseGroupNormOpCl is equal to closed(2), this item define the time del… |
| 1.3.6.1.4.1.81.19.1.1.1.20 | lseGroupAutoPartitionEnable | 0 | 0 | Enables autopartition mechanism support in the group level for each port of the group. |
| 1.3.6.1.4.1.81.19.1.1.1.21 | lseGroupWorkState | 0 | 0 | One of the possible states of the module: this item indicates if the module is runing or booting. The value runAndBoot(3) indicat… |
| 1.3.6.1.4.1.81.19.1.1.1.22 | lseGroupBITResult | 0 | 0 | The Bit Indication Test in state 'faulty' indicates a problem. The agent should send a fault trap in this case. |
| 1.3.6.1.4.1.81.19.1.1.1.23 | lseGroupAssignSlots | 0 | 0 | In a multi-backbone configuration within a single HUB, this item enables to assign backbone module with specific slot numbers. … |
| 1.3.6.1.4.1.81.19.1.1.1.25 | lseGroupEnableHSBReset | 0 | 0 | This item enables/disables the HSB Reset mechanism in the module. |