The value of upsEstimatedMinutesRemaining at which a
lowBattery condition is declared. For agents which
support only discrete (discontinuous) values, then the
agent shall round up to the next supported value. If
the requested value is larger than the largest
supported value, then the largest supported value
shall be selected.(*)
Parsed from file GE_PARALLELUPS.mib.txt
Company: ge
Module: GE_PARALLELUPS
Vendor: IMV Victron bv
Module: GE_PARALLELUPS
[Automatically extracted from oidview.com]
upsConfigLowBattTime_first OBJECT-TYPE SYNTAX NonNegativeInteger32 UNITS "minutes" MAX-ACCESS read-write STATUS current DESCRIPTION "The value of upsEstimatedMinutesRemaining at which a lowBattery condition is declared. For agents which support only discrete (discontinuous) values, then the agent shall round up to the next supported value. If the requested value is larger than the largest supported value, then the largest supported value shall be selected.(*)" ::= { upsConfig_first 7 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.818.1.1.11.9.7.0 | 0 | 0 | 0 | upsConfigLowBattTime_first |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.818.1.1.11.9.1 | upsConfigInputVoltage_first | 1 | 1 | The magnitude of the nominal input voltage. On those systems which support read-write access to this object, if there is an atte… |
| 1.3.6.1.4.1.818.1.1.11.9.2 | upsConfigInputFreq_first | 1 | 1 | The nominal input frequency. On those systems which support read-write access to this object, if there is an attempt to set this… |
| 1.3.6.1.4.1.818.1.1.11.9.3 | upsConfigOutputVoltage_first | 1 | 1 | The magnitude of the nominal output voltage. On those systems which support read-write access to this object, if there is an att… |
| 1.3.6.1.4.1.818.1.1.11.9.4 | upsConfigOutputFreq_first | 1 | 1 | The nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set thi… |
| 1.3.6.1.4.1.818.1.1.11.9.5 | upsConfigOutputVA_first | 1 | 1 | The magnitude of the nominal Volt-Amp rating.(*) |
| 1.3.6.1.4.1.818.1.1.11.9.6 | upsConfigOutputPower_first | 1 | 1 | The magnitude of the nominal true power rating.(*) |
| 1.3.6.1.4.1.818.1.1.11.9.8 | upsConfigAudibleStatus_first | 1 | 1 | The requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state i… |
| 1.3.6.1.4.1.818.1.1.11.9.9 | upsConfigLowVoltageTransferPoint_first | 1 | 1 | The minimum input line voltage allowed before the UPS system transfers to battery backup.(*) |
| 1.3.6.1.4.1.818.1.1.11.9.10 | upsConfigHighVoltageTransferPoint_first | 1 | 1 | The maximum line voltage allowed before the UPS system transfers to battery backup.(*) |
| 1.3.6.1.4.1.818.1.1.11.9.11 | upsConfigBatteryCapacity_first | 1 | 1 | The installed battery capacity. This value is the 'factory'-value, not the value after calibration. |
| 1.3.6.1.4.1.818.1.1.11.9.12 | upsConfigBatteryChargeCurrent_first | 1 | 1 | The maximum battery charge current, including external chargers. |
| 1.3.6.1.4.1.818.1.1.11.9.13 | upsConfigNoLoadShutdown_first | 1 | 1 | Dis- or enable 'no load' shutdown from the contact interface. |
| 1.3.6.1.4.1.818.1.1.11.9.14 | upsConfigStartDelay_first | 1 | 1 | Minimum required autonomy time before the UPS may perform an autorestart. |