This parameter is used to set the wireless NIC Operational mode.
Depending on the wireless NIC in the device different wireless
operational modes can be configured. The object wirelessIfSupportedOperationalMode
shows the supported modes and the possible supported modes for
AP products:
dot11b(1),
dot11g(2),
dot11ng(3),
dot11a(4),
dot11na(5)
Parsed from file PROXIM-MIB.mib
Module: PROXIM-MIB
Vendor: Proxim Wireless, Inc
Module: PROXIM-MIB
[Automatically extracted from oidview.com]
wirelessIfOperationalMode OBJECT-TYPE SYNTAX DisplayString (SIZE(1..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "This parameter is used to set the wireless NIC Operational mode. Depending on the wireless NIC in the device different wireless operational modes can be configured. The object wirelessIfSupportedOperationalMode shows the supported modes and the possible supported modes for AP products: dot11b(1), dot11g(2), dot11ng(3), dot11a(4), dot11na(5)" ::= { wirelessIfPropertiesTableEntry 3 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.841.1.1.1.1.1.1.1.1 | wirelessIfPropertiesTableIndex | 0 | 0 | This parameter represents a unique value for each Wireless interface in the system and is used as index to this table. |
| 1.3.6.1.4.1.841.1.1.1.1.1.1.1.2 | wirelessIfPropertiesRadioStatus | 0 | 0 | This parameter is used to provide the status of the Wireless Radio interface. Select (1) to enable the wireless interface and (2) … |
| 1.3.6.1.4.1.841.1.1.1.1.1.1.1.4 | wirelessIfSupportedOperationalMode | 0 | 0 | This parameter is used to set the wireless supported Operational mode. |
| 1.3.6.1.4.1.841.1.1.1.1.1.1.1.5 | wirelessIfCurrentChannelBandwidth | 0 | 0 | This parameter represents the current bandwidth that Wireless is currently operating on. It is represented in MHz |
| 1.3.6.1.4.1.841.1.1.1.1.1.1.1.6 | wirelessIfSupportedChannelBandwidth | 0 | 0 | This parameter represents the channel bandwidths that a wireless can support. |
| 1.3.6.1.4.1.841.1.1.1.1.1.1.1.7 | wirelessIfAutoChannelSelection | 0 | 0 | This parameter is used to configure the auto channel selection for wireless interface. Select (1) to enable the auto channel sele… |
| 1.3.6.1.4.1.841.1.1.1.1.1.1.1.8 | wirelessIfCurrentOperatingChannel | 0 | 0 | This parameter represents the user configured channel that the radio is configured to operate in. Note: It is possible that the c… |
| 1.3.6.1.4.1.841.1.1.1.1.1.1.1.9 | wirelessIfSupportedChannels | 0 | 0 | This parameter represents the channels that wireless can support. |
| 1.3.6.1.4.1.841.1.1.1.1.1.1.1.10 | wirelessIfAutoRateSelection | 0 | 0 | This parameter is used to configure the value for Auto Rate Selection for the wireless interface. Select (1) to enable the Auto R… |
| 1.3.6.1.4.1.841.1.1.1.1.1.1.1.11 | wirelessIfTransmittedRate | 0 | 0 | wirelessIftransmittedRate |
| 1.3.6.1.4.1.841.1.1.1.1.1.1.1.12 | wirelessIfSupportedRate | 0 | 0 | This parameter represents the number of rates supported for wireless. |
| 1.3.6.1.4.1.841.1.1.1.1.1.1.1.13 | wirelessIfVAPRTSThreshold | 0 | 0 | This parameter represents the maximum threshold for VAP RTS (Request To Send). The maximum threshold can be configured up to 234… |
| 1.3.6.1.4.1.841.1.1.1.1.1.1.1.14 | wirelessIfVAPBeaconInterval | 0 | 0 | This parameter represents the time interval that a beacon takes for getting transmitted for wireless VAP. By default, the value … |
| 1.3.6.1.4.1.841.1.1.1.1.1.1.1.15 | wirelessIfTPC | 0 | 0 | wirelessIftpC |
| 1.3.6.1.4.1.841.1.1.1.1.1.1.1.16 | wirelessIfCellSize | 0 | 0 | This parameter represents the cell size of the wireless. By default, the cell size is configured to large. Select (1) for Small c… |
| 1.3.6.1.4.1.841.1.1.1.1.1.1.1.17 | wirelessIfDTIM | 0 | 0 | This parameter represents the delivery traffic indication map period. This is the interval between the transmission of multicas… |
| 1.3.6.1.4.1.841.1.1.1.1.1.1.1.18 | wirelessIfAntennaGain | 0 | 0 | This parameter is used to configure the antenna gain. |
| 1.3.6.1.4.1.841.1.1.1.1.1.1.1.19 | wirelessIfCurrentActiveChannel | 0 | 0 | This parameter represents the current active channel that wireless radio is operating on. It may be different from the configure… |
| 1.3.6.1.4.1.841.1.1.1.1.1.1.1.20 | wirelessIfSatelliteDensity | 0 | 0 | This parameter represents the density of the satellites for the BSU. It configures the BSU to accomodate the satellites for the … |
| 1.3.6.1.4.1.841.1.1.1.1.1.1.1.21 | wirelessIfMPOperationalMode | 0 | 0 | This parameter is used to set the wireless NIC Operational mode for Tsunami Multi Point Products. |
| 1.3.6.1.4.1.841.1.1.1.1.1.1.1.22 | wirelessIfChannelWaitTime | 0 | 0 | This parameter is used to configure the DFS channel wait time. |
| 1.3.6.1.4.1.841.1.1.1.1.1.1.1.23 | wirelessIfActiveTPC | 0 | 0 | This parameter shows the active cell size that the transmitted power controls. It is measured in dBm |
| 1.3.6.1.4.1.841.1.1.1.1.1.1.1.24 | wirelessIfDfsNumSatWithRadarForFreqSwitch | 0 | 0 | This parameter represents the minimum number of satellites reporting RADAR for BSU to switch to a new best channel/frequency. Th… |
| 1.3.6.1.4.1.841.1.1.1.1.1.1.1.25 | wirelessIfDfsStatus | 0 | 0 | This parameter is used to configure the status of the DFS for SU. Configuring this parameter for BSU will not affecte BSU Status… |