DMI: Diagnostic Monitoring Interface for fiber
transceivers. Receive power on local fiber
measured in microwatts.
Parsed from file TNI-MIB.mib
Module: TNI-MIB
Vendor: Transition Engineering Inc.
Module: TNI-MIB
[Automatically extracted from oidview.com]
sfbrm100DMIRxPowerLevel OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "DMI: Diagnostic Monitoring Interface for fiber transceivers. Receive power on local fiber measured in microwatts." ::= { sfbrm100DMIEntry 19 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.868.2.3.1.3.3.1.1 | sfbrm100DMILocPortIndex | 0 | 0 | The port index of the DMI port as defined by sfbrm100PortLocIndex. |
1.3.6.1.4.1.868.2.3.1.3.3.1.2 | sfbrm100DMIRmtPortIndex | 0 | 0 | The port index of the DMI port as defined by sfbrm100PortRmtIndex. |
1.3.6.1.4.1.868.2.3.1.3.3.1.3 | sfbrm100DMIRxPwrLvlPreset | 0 | 0 | A preset level for Rx Power on the Fiber port, if the DMI read value falls below the preset value, an intrusion is detected, and… |
1.3.6.1.4.1.868.2.3.1.3.3.1.4 | sfbrm100DMIConnType | 0 | 0 | The DMI connector type indicates the external optical or electrical cable connector provided as the interface. From SFF 8472 Rev… |
1.3.6.1.4.1.868.2.3.1.3.3.1.5 | sfbrm100DMIBitRate | 0 | 0 | Bitrate in units of 100Mbps. |
1.3.6.1.4.1.868.2.3.1.3.3.1.6 | sfbrm100DMILenFor9x125umKM | 0 | 0 | Specifies the link length that is supported by the transceiver while operating in single mode fiber. The value is in units of KM. |
1.3.6.1.4.1.868.2.3.1.3.3.1.7 | sfbrm100DMILenFor9x125um100M | 0 | 0 | Specifies the link length that is supported by the transceiver while operating in single mode fiber. The value is in units of 10… |
1.3.6.1.4.1.868.2.3.1.3.3.1.8 | sfbrm100DMILenFor50x125um10M | 0 | 0 | Specifies the link length that is supported by the transceiver while operating in 50 micron multi mode fiber. The value is in un… |
1.3.6.1.4.1.868.2.3.1.3.3.1.9 | sfbrm100DMILenFor625x125um10M | 0 | 0 | Specifies the link length that is supported by the transceiver while operating in 62.5 micron multi mode fiber. The value is in … |
1.3.6.1.4.1.868.2.3.1.3.3.1.10 | sfbrm100DMILenForCopper | 0 | 0 | Specifies the link length that is supported by the transceiver while operating in copper cable. The value is in units of meters. |
1.3.6.1.4.1.868.2.3.1.3.3.1.11 | sfbrm100DMIId | 0 | 0 | Specifies the physical device. The table below from SFF-8472 Rev 9.5 Standard gives description for the values. 00h Unknown or uns… |
1.3.6.1.4.1.868.2.3.1.3.3.1.12 | sfbrm100DMILaserWavelength | 0 | 0 | The Nominal transmitter output wavelength at room temperature. The units in nm |
1.3.6.1.4.1.868.2.3.1.3.3.1.13 | sfbrm100DMITemperature | 0 | 0 | Temperature of fiber transceiver in tenths of degrees C. |
1.3.6.1.4.1.868.2.3.1.3.3.1.14 | sfbrm100DMITempAlarm | 0 | 0 | . |
1.3.6.1.4.1.868.2.3.1.3.3.1.15 | sfbrm100DMITxBiasCurrent | 0 | 0 | Transmit bias current on local fiber interface, in microamperes. |
1.3.6.1.4.1.868.2.3.1.3.3.1.16 | sfbrm100DMITxBiasAlarm | 0 | 0 | . |
1.3.6.1.4.1.868.2.3.1.3.3.1.17 | sfbrm100DMITxPowerLevel | 0 | 0 | DMI: Diagnostic Monitoring Interface for fiber transceivers. Transmit power on local fiber measured in microwatts. |
1.3.6.1.4.1.868.2.3.1.3.3.1.18 | sfbrm100DMITxPowerAlarm | 0 | 0 | . |
1.3.6.1.4.1.868.2.3.1.3.3.1.20 | sfbrm100DMIRxPowerAlarm | 0 | 0 | . |