This table contains information about Frame Relay
end-points of FR-ATM interworking connections on the
switch. When an entry is created in this table, the
agent creates a corresponding entry in the
atmVclTable of ATM-MIB, to represent the
configuration on the internal ATM port. The mapping
between an entry in this table, and the corresponding
entry in the atmVclTable is shown in the
casfFAMapTable and the casfAFMapTable.
Entries can be created or deleted in this table by an
NMS using the casfVcEndptRowStatus object.
To create a PVC connection end-point, the value of
casfVcEndptConnKind must be 'pvc'.
To create a soft VC initiator end-point, set the value of
casfVcEndptConnKind to 'spvcInitiator', and specify
the value of casfVcEndptSpvcRemoteAddr and
casfVcEndptSpvcRemoteType.
If the value of casfVcEndptSpvcRemoteType is
'frameRelay', you must also specify the value of
casfVcEndptSpvcRemoteDlci. Activating the conceptual
row will then cause the agent to attempt to establish
a connection to the remote frame relay interface.
If the value of casfVcEndptSpvcRemoteType is 'atm',
you must specify the values of
casfVcEndptSpvcRemoteVpi and
casfVcEndptSpvcRemoteVci. Activating the conceptual row
will then cause the agent to attempt to establish a
connection to the remote ATM interface.
The agent creates an entry in this table when an
incoming signaling request causes a soft VC
connection to be established with a local frame relay
interface as the destination. The value of
casfVcEndptConnKind in this case will be
'spvcTarget'. Such entries cannot be modified or
deleted by network management. They will be deleted
when the connection is removed by signaling.
Parsed from file CISCO-ATM-SWITCH-FR-IWF-MIB.mib
Module: CISCO-ATM-SWITCH-FR-IWF-MIB
This table contains information about Frame Relay
end-points of FR-ATM interworking connections on the
switch. When an entry is created in this table, the
agent creates a corresponding entry in the
atmVclTable of ATM-MIB, to represent the
configuration on the internal ATM port. The mapping
between an entry in this table, and the corresponding
entry in the atmVclTable is shown in the
casfFAMapTable and the casfAFMapTable.
Entries can be created or deleted in this table by an
NMS using the casfVcEndptRowStatus object.
To create a PVC connection end-point, the value of
casfVcEndptConnKind must be 'pvc'.
To create a soft VC initiator end-point, set the value of
casfVcEndptConnKind to 'spvcInitiator', and specify
the value of casfVcEndptSpvcRemoteAddr and
casfVcEndptSpvcRemoteType.
If the value of casfVcEndptSpvcRemoteType is
'frameRelay', you must also specify the value of
casfVcEndptSpvcRemoteDlci. Activating the conceptual
row will then cause the agent to attempt to establish
a connection to the remote frame relay interface.
If the value of casfVcEndptSpvcRemoteType is 'atm',
you must specify the values of
casfVcEndptSpvcRemoteVpi and
casfVcEndptSpvcRemoteVci. Activating the conceptual row
will then cause the agent to attempt to establish a
connection to the remote ATM interface.
The agent creates an entry in this table when an
incoming signaling request causes a soft VC
connection to be established with a local frame relay
interface as the destination. The value of
casfVcEndptConnKind in this case will be
'spvcTarget'. Such entries cannot be modified or
deleted by network management. They will be deleted
when the connection is removed by signaling.
casfVcEndptTable OBJECT-TYPE
SYNTAX SEQUENCE OF CasfVcEndptEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information about Frame Relay
end-points of FR-ATM interworking connections on the
switch. When an entry is created in this table, the
agent creates a corresponding entry in the
atmVclTable of ATM-MIB, to represent the
configuration on the internal ATM port. The mapping
between an entry in this table, and the corresponding
entry in the atmVclTable is shown in the
casfFAMapTable and the casfAFMapTable.
Entries can be created or deleted in this table by an
NMS using the casfVcEndptRowStatus object.
To create a PVC connection end-point, the value of
casfVcEndptConnKind must be pvc.
To create a soft VC initiator end-point, set the value of
casfVcEndptConnKind to spvcInitiator, and specify
the value of casfVcEndptSpvcRemoteAddr and
casfVcEndptSpvcRemoteType.
If the value of casfVcEndptSpvcRemoteType is
rameRelay, you must also specify the value of
casfVcEndptSpvcRemoteDlci. Activating the conceptual
row will then cause the agent to attempt to establish
a connection to the remote frame relay interface.
If the value of casfVcEndptSpvcRemoteType is atm,
you must specify the values of
casfVcEndptSpvcRemoteVpi and
casfVcEndptSpvcRemoteVci. Activating the conceptual row
will then cause the agent to attempt to establish a
connection to the remote ATM interface.
The agent creates an entry in this table when an
incoming signaling request causes a soft VC
connection to be established with a local frame relay
interface as the destination. The value of
casfVcEndptConnKind in this case will be
spvcTarget. Such entries cannot be modified or
deleted by network management. They will be deleted
when the connection is removed by signaling."
View at oid-info.com
This table contains information about Frame Relay
end-points of FR-ATM interworking connections on the
switch. When an entry is created in this table, the
agent creates a corresponding entry in the
atmVclTable of ATM-MIB, to represent the
configuration on the internal ATM port. The mapping
between an entry in this table, and the corresponding
entry in the atmVclTable is shown in the
casfFAMapTable and the casfAFMapTable.
Entries can be created or deleted in this table by an
NMS using the casfVcEndptRowStatus object.
To create a PVC connection end-point, the value of
casfVcEndptConnKind must be 'pvc'.
To create a soft VC initiator end-point, set the value of
casfVcEndptConnKind to 'spvcInitiator', and specify
the value of casfVcEndptSpvcRemoteAddr and
casfVcEndptSpvcRemoteType.
If the value of casfVcEndptSpvcRemoteType is
'frameRelay', you must also specify the value of
casfVcEndptSpvcRemoteDlci. Activating the conceptual
row will then cause the agent to attempt to establish
a connection to the remote frame relay interface.
If the value of casfVcEndptSpvcRemoteType is 'atm',
you must specify the values of
casfVcEndptSpvcRemoteVpi and
casfVcEndptSpvcRemoteVci. Activating the conceptual row
will then cause the agent to attempt to establish a
connection to the remote ATM interface.
The agent creates an entry in this table when an
incoming signaling request causes a soft VC
connection to be established with a local frame relay
interface as the destination. The value of
casfVcEndptConnKind in this case will be
'spvcTarget'. Such entries cannot be modified or
deleted by network management. They will be deleted
when the connection is removed by signaling.
Parsed from file CISCO-ATM-SWITCH-FR-IWF-MIB.my.txt
Company: None
Module: CISCO-ATM-SWITCH-FR-IWF-MIB
This table contains information about Frame Relay
end-points of FR-ATM interworking connections on the
switch. When an entry is created in this table, the
agent creates a corresponding entry in the
atmVclTable of ATM-MIB, to represent the
configuration on the internal ATM port. The mapping
between an entry in this table, and the corresponding
entry in the atmVclTable is shown in the
casfFAMapTable and the casfAFMapTable.
Entries can be created or deleted in this table by an
NMS using the casfVcEndptRowStatus object.
To create a PVC connection end-point, the value of
casfVcEndptConnKind must be 'pvc'.
To create a soft VC initiator end-point, set the value of
casfVcEndptConnKind to 'spvcInitiator', and specify
the value of casfVcEndptSpvcRemoteAddr and
casfVcEndptSpvcRemoteType.
If the value of casfVcEndptSpvcRemoteType is
'frameRelay', you must also specify the value of
casfVcEndptSpvcRemoteDlci. Activating the conceptual
row will then cause the agent to attempt to establish
a connection to the remote frame relay interface.
If the value of casfVcEndptSpvcRemoteType is 'atm',
you must specify the values of
casfVcEndptSpvcRemoteVpi and
casfVcEndptSpvcRemoteVci. Activating the conceptual row
will then cause the agent to attempt to establish a
connection to the remote ATM interface.
The agent creates an entry in this table when an
incoming signaling request causes a soft VC
connection to be established with a local frame relay
interface as the destination. The value of
casfVcEndptConnKind in this case will be
'spvcTarget'. Such entries cannot be modified or
deleted by network management. They will be deleted
when the connection is removed by signaling.
casfVcEndptTable OBJECT-TYPE SYNTAX SEQUENCE OF CasfVcEndptEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information about Frame Relay end-points of FR-ATM interworking connections on the switch. When an entry is created in this table, the agent creates a corresponding entry in the atmVclTable of ATM-MIB, to represent the configuration on the internal ATM port. The mapping between an entry in this table, and the corresponding entry in the atmVclTable is shown in the casfFAMapTable and the casfAFMapTable. Entries can be created or deleted in this table by an NMS using the casfVcEndptRowStatus object. To create a PVC connection end-point, the value of casfVcEndptConnKind must be 'pvc'. To create a soft VC initiator end-point, set the value of casfVcEndptConnKind to 'spvcInitiator', and specify the value of casfVcEndptSpvcRemoteAddr and casfVcEndptSpvcRemoteType. If the value of casfVcEndptSpvcRemoteType is 'frameRelay', you must also specify the value of casfVcEndptSpvcRemoteDlci. Activating the conceptual row will then cause the agent to attempt to establish a connection to the remote frame relay interface. If the value of casfVcEndptSpvcRemoteType is 'atm', you must specify the values of casfVcEndptSpvcRemoteVpi and casfVcEndptSpvcRemoteVci. Activating the conceptual row will then cause the agent to attempt to establish a connection to the remote ATM interface. The agent creates an entry in this table when an incoming signaling request causes a soft VC connection to be established with a local frame relay interface as the destination. The value of casfVcEndptConnKind in this case will be 'spvcTarget'. Such entries cannot be modified or deleted by network management. They will be deleted when the connection is removed by signaling." ::= { casfFrVC 1 }
casfVcEndptTable OBJECT-TYPE SYNTAX SEQUENCE OF CasfVcEndptEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains information about Frame Relay end-points of FR-ATM interworking connections on the switch. When an entry is created in this table, the agent creates a corresponding entry in the atmVclTable of ATM-MIB, to represent the configuration on the internal ATM port. The mapping between an entry in this table, and the corresponding entry in the atmVclTable is shown in the casfFAMapTable and the casfAFMapTable. Entries can be created or deleted in this table by an NMS using the casfVcEndptRowStatus object. To create a PVC connection end-point, the value of casfVcEndptConnKind must be 'pvc'. To create a soft VC initiator end-point, set the value of casfVcEndptConnKind to 'spvcInitiator', and specify the value of casfVcEndptSpvcRemoteAddr and casfVcEndptSpvcRemoteType. If the value of casfVcEndptSpvcRemoteType is 'frameRelay', you must also specify the value of casfVcEndptSpvcRemoteDlci. Activating the conceptual row will then cause the agent to attempt to establish a connection to the remote frame relay interface. If the value of casfVcEndptSpvcRemoteType is 'atm', you must specify the values of casfVcEndptSpvcRemoteVpi and casfVcEndptSpvcRemoteVci. Activating the conceptual row will then cause the agent to attempt to establish a connection to the remote ATM interface. The agent creates an entry in this table when an incoming signaling request causes a soft VC connection to be established with a local frame relay interface as the destination. The value of casfVcEndptConnKind in this case will be 'spvcTarget'. Such entries cannot be modified or deleted by network management. They will be deleted when the connection is removed by signaling." ::= { casfFrVC 1 }
Automatically extracted from Cisco "SNMP v2 MIBs".
casfVcEndptTable OBJECT-TYPE SYNTAX SEQUENCE OF CasfVcEndptEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information about Frame Relay end-points of FR-ATM interworking connections on the switch. When an entry is created in this table, the agent creates a corresponding entry in the atmVclTable of ATM-MIB, to represent the configuration on the internal ATM port. The mapping between an entry in this table, and the corresponding entry in the atmVclTable is shown in the casfFAMapTable and the casfAFMapTable. Entries can be created or deleted in this table by an NMS using the casfVcEndptRowStatus object. To create a PVC connection end-point, the value of casfVcEndptConnKind must be 'pvc'. To create a soft VC initiator end-point, set the value of casfVcEndptConnKind to 'spvcInitiator', and specify the value of casfVcEndptSpvcRemoteAddr and casfVcEndptSpvcRemoteType. If the value of casfVcEndptSpvcRemoteType is 'frameRelay', you must also specify the value of casfVcEndptSpvcRemoteDlci. Activating the conceptual row will then cause the agent to attempt to establish a connection to the remote frame relay interface. If the value of casfVcEndptSpvcRemoteType is 'atm', you must specify the values of casfVcEndptSpvcRemoteVpi and casfVcEndptSpvcRemoteVci. Activating the conceptual row will then cause the agent to attempt to establish a connection to the remote ATM interface. The agent creates an entry in this table when an incoming signaling request causes a soft VC connection to be established with a local frame relay interface as the destination. The value of casfVcEndptConnKind in this case will be 'spvcTarget'. Such entries cannot be modified or deleted by network management. They will be deleted when the connection is removed by signaling." ::= { casfFrVC 1 }
casfVcEndptTable OBJECT-TYPE SYNTAX SEQUENCE OF CasfVcEndptEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information about Frame Relay end-points of FR-ATM interworking connections on the switch. When an entry is created in this table, the agent creates a corresponding entry in the atmVclTable of ATM-MIB, to represent the configuration on the internal ATM port. The mapping between an entry in this table, and the corresponding entry in the atmVclTable is shown in the casfFAMapTable and the casfAFMapTable. Entries can be created or deleted in this table by an NMS using the casfVcEndptRowStatus object. To create a PVC connection end-point, the value of casfVcEndptConnKind must be 'pvc'. To create a soft VC initiator end-point, set the value of casfVcEndptConnKind to 'spvcInitiator', and specify the value of casfVcEndptSpvcRemoteAddr and casfVcEndptSpvcRemoteType. If the value of casfVcEndptSpvcRemoteType is 'frameRelay', you must also specify the value of casfVcEndptSpvcRemoteDlci. Activating the conceptual row will then cause the agent to attempt to establish a connection to the remote frame relay interface. If the value of casfVcEndptSpvcRemoteType is 'atm', you must specify the values of casfVcEndptSpvcRemoteVpi and casfVcEndptSpvcRemoteVci. Activating the conceptual row will then cause the agent to attempt to establish a connection to the remote ATM interface. The agent creates an entry in this table when an incoming signaling request causes a soft VC connection to be established with a local frame relay interface as the destination. The value of casfVcEndptConnKind in this case will be 'spvcTarget'. Such entries cannot be modified or deleted by network management. They will be deleted when the connection is removed by signaling." ::= { casfFrVC 1 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.9.9.112.1.2.1.1 | casfVcEndptEntry | 20 | 20 | Models a bidirectional Frame Relay VC end-point. The ifIndex identifies an ifTable entry for a Frame Relay interface on this deviā¦ |