Reference record for OID 1.3.6.1.4.1.9.9.121.1.1.6



parent
1.3.6.1.4.1.9.9.121.1.1 (cncGlobal)
node code
6
node name
cncNcdpHoldTime
dot oid
1.3.6.1.4.1.9.9.121.1.1.6
type
OBJECT-TYPE
asn1 oid
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) enterprise(1) cisco(9) ciscoMgmt(9) ciscoAtmNetworkClockMIB(121) ciscoAtmNetworkClockMIBObjects(1) cncGlobal(1) cncNcdpHoldTime(6)}
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) enterprises(1) cisco(9) ciscoMgmt(9) ciscoAtmNetworkClockMIB(121) ciscoAtmNetworkClockMIBObjects(1) cncGlobal(1) cncNcdpHoldTime(6)}
  • {iso(1) org(3) dod(6) internet(1) private(4) enterprise(1) cisco(9) ciscoMgmt(9) ciscoAtmNetworkClockMIB(121) ciscoAtmNetworkClockMIBObjects(1) cncGlobal(1) cncNcdpHoldTime(6)}
  • {iso(1) org(3) dod(6) internet(1) private(4) enterprises(1) cisco(9) ciscoMgmt(9) ciscoAtmNetworkClockMIB(121) ciscoAtmNetworkClockMIBObjects(1) cncGlobal(1) cncNcdpHoldTime(6)}
  • {iso(1) iso-identified-organization(3) dod(6) internet(1) private(4) enterprise(1) cisco(9) ciscoMgmt(9) ciscoAtmNetworkClockMIB(121) ciscoAtmNetworkClockMIBObjects(1) cncGlobal(1) cncNcdpHoldTime(6)}
  • {iso(1) iso-identified-organization(3) dod(6) internet(1) private(4) enterprises(1) cisco(9) ciscoMgmt(9) ciscoAtmNetworkClockMIB(121) ciscoAtmNetworkClockMIBObjects(1) cncGlobal(1) cncNcdpHoldTime(6)}
    • iri oid
  • /iso/identified-organization/dod/internet/private/enterprise/cisco/ciscoMgmt/ciscoAtmNetworkClockMIB/ciscoAtmNetworkClockMIBObjects/cncGlobal/cncNcdpHoldTime
  • /iso/identified-organization/dod/internet/private/enterprises/cisco/ciscoMgmt/ciscoAtmNetworkClockMIB/ciscoAtmNetworkClockMIBObjects/cncGlobal/cncNcdpHoldTime
  • /iso/org/dod/internet/private/enterprise/cisco/ciscoMgmt/ciscoAtmNetworkClockMIB/ciscoAtmNetworkClockMIBObjects/cncGlobal/cncNcdpHoldTime
  • /iso/org/dod/internet/private/enterprises/cisco/ciscoMgmt/ciscoAtmNetworkClockMIB/ciscoAtmNetworkClockMIBObjects/cncGlobal/cncNcdpHoldTime
  • /iso/iso-identified-organization/dod/internet/private/enterprise/cisco/ciscoMgmt/ciscoAtmNetworkClockMIB/ciscoAtmNetworkClockMIBObjects/cncGlobal/cncNcdpHoldTime
  • /iso/iso-identified-organization/dod/internet/private/enterprises/cisco/ciscoMgmt/ciscoAtmNetworkClockMIB/ciscoAtmNetworkClockMIBObjects/cncGlobal/cncNcdpHoldTime
    • iri by oid_info
    /ISO/Identified-Organization/6/1/4/1/9/9/121/1/1/6

    Description by circitor

    The delay between the transmission of NCDP configuration
    PDUs.

    The hold time is used to limit the transmission of NCDP
    configuration PDUs out of an interface to a maximum of one
    configuration PDU per hold time interval per interface.

    The value of this object should normally be set to match the
    value of cncNcdpMessageInterval. If the value of this
    object is higher than the value of cncNcdpMessageInterval,
    NCDP configuration PDUs will end up being propagated at
    the rate specified by the value of this object instead.

    This object is only used by the NCDP protocol entity.

    Parsed from file CISCO-ATM-NETWORK-CLOCK-MIB.mib
    Module: CISCO-ATM-NETWORK-CLOCK-MIB

    Description by cisco_v1

    The delay between the transmission of NCDP configuration
    PDUs.

    The hold time is used to limit the transmission of NCDP
    configuration PDUs out of an interface to a maximum of one
    configuration PDU per hold time interval per interface.

    The value of this object should normally be set to match the
    value of cncNcdpMessageInterval. If the value of this
    object is higher than the value of cncNcdpMessageInterval,
    NCDP configuration PDUs will end up being propagated at
    the rate specified by the value of this object instead.

    This object is only used by the NCDP protocol entity.

    Description by mibdepot

    The delay between the transmission of NCDP configuration
    PDUs.

    The hold time is used to limit the transmission of NCDP
    configuration PDUs out of an interface to a maximum of one
    configuration PDU per hold time interval per interface.

    The value of this object should normally be set to match the
    value of cncNcdpMessageInterval. If the value of this
    object is higher than the value of cncNcdpMessageInterval,
    NCDP configuration PDUs will end up being propagated at
    the rate specified by the value of this object instead.

    This object is only used by the NCDP protocol entity.

    Parsed from file CISCO-ATM-NETWORK-CLOCK-MIB.my.txt
    Company: None
    Module: CISCO-ATM-NETWORK-CLOCK-MIB

    Description by cisco

    The delay between the transmission of NCDP configuration
    PDUs.

    The hold time is used to limit the transmission of NCDP
    configuration PDUs out of an interface to a maximum of one
    configuration PDU per hold time interval per interface.

    The value of this object should normally be set to match the
    value of cncNcdpMessageInterval. If the value of this
    object is higher than the value of cncNcdpMessageInterval,
    NCDP configuration PDUs will end up being propagated at
    the rate specified by the value of this object instead.

    This object is only used by the NCDP protocol entity.

    Information by circitor

    cncNcdpHoldTime OBJECT-TYPE
    SYNTAX          Integer32 (75..60000 )
    UNITS           "milliseconds"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "The delay between the transmission of NCDP configuration
        PDUs.

        The hold time is used to limit the transmission of NCDP 
        configuration PDUs out of an interface to a maximum of one
        configuration PDU per hold time interval per interface.

        The value of this object should normally be set        to match the 
        value of cncNcdpMessageInterval.  If the value of this 
        object is higher than the value of cncNcdpMessageInterval,
        NCDP configuration PDUs will end up being propagated at
        the rate specified by the value of this object instead.

        This object is only used by the NCDP protocol entity."
    DEFVAL          { 500 } 
    ::= { cncGlobal 6 }

    Information by cisco_v1

    cncNcdpHoldTime OBJECT-TYPE
    SYNTAX INTEGER(75..60000)


    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "The delay between the transmission of NCDP configuration
        PDUs.
        
        The hold time is used to limit the transmission of NCDP 
        configuration PDUs out of an interface to a maximum of one
        configuration PDU per hold time interval per interface.
        
        The value of this object should normally be set        to match the 
        value of cncNcdpMessageInterval.  If the value of this 
        object is higher than the value of cncNcdpMessageInterval,
        NCDP configuration PDUs will end up being propagated at
        the rate specified by the value of this object instead.
        
        This object is only used by the NCDP protocol entity."
    DEFVAL { 500 }
    ::= { cncGlobal 6 }

    Information by oid_info

    Vendor: Cisco
    Module: CISCO-ATM-NETWORK-CLOCK-MIB

    [Automatically extracted from oidview.com]

    Information by mibdepot

    cncNcdpHoldTime OBJECT-TYPE
    SYNTAX          Integer32 (75..60000 )
    UNITS           "milliseconds"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "The delay between the transmission of NCDP configuration
        PDUs.

        The hold time is used to limit the transmission of NCDP 
        configuration PDUs out of an interface to a maximum of one
        configuration PDU per hold time interval per interface.

        The value of this object should normally be set        to match the 
        value of cncNcdpMessageInterval.  If the value of this 
        object is higher than the value of cncNcdpMessageInterval,
        NCDP configuration PDUs will end up being propagated at
        the rate specified by the value of this object instead.

        This object is only used by the NCDP protocol entity."
    DEFVAL          { 500 } 
    ::= { cncGlobal 6 }

    Information by cisco

    cncNcdpHoldTime OBJECT-TYPE
    SYNTAX          Integer32 (75..60000 )
    UNITS           "milliseconds"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "The delay between the transmission of NCDP configuration
        PDUs.

        The hold time is used to limit the transmission of NCDP 
        configuration PDUs out of an interface to a maximum of one
        configuration PDU per hold time interval per interface.

        The value of this object should normally be set        to match the 
        value of cncNcdpMessageInterval.  If the value of this 
        object is higher than the value of cncNcdpMessageInterval,
        NCDP configuration PDUs will end up being propagated at
        the rate specified by the value of this object instead.

        This object is only used by the NCDP protocol entity."
    DEFVAL          { 500 } 
    ::= { cncGlobal 6 }

    First Registration Authority (recovered by parent 1.3.6.1.4.1.9)

    Greg Satz

    Current Registration Authority (recovered by parent 1.3.6.1.4.1.9)

    Cisco Systems, Inc.

    Children (1)

    OIDNameSub childrenSub Nodes TotalDescription
    1.3.6.1.4.1.9.9.121.1.1.6.0 cncNcdpHoldTime 0 0 None

    Brothers (8)

    OIDNameSub childrenSub Nodes TotalDescription
    1.3.6.1.4.1.9.9.121.1.1.1 cncDistributionMethod 1 1 The method used to distribute network clock for the device.
    When the mode of operation is 'ncdp', the services provided
    by the NC…
    1.3.6.1.4.1.9.9.121.1.1.2 cncNotificationOnChange 1 1 The value of this object determines whether a notification
    should be generated due to a change in the device's root
    clock source …
    1.3.6.1.4.1.9.9.121.1.1.3 cncNodeStratum 1 1 The stratum at which the device exists in the Synchronous
    Digital Hierarchy (See American National Standards
    Institute, ANSI T1.1…
    1.3.6.1.4.1.9.9.121.1.1.4 cncNcdpMaxDiameter 1 1 The maximum possible height of a network clock distribution
    tree in the network. (Alternatively this is known as the
    maximum dia…
    1.3.6.1.4.1.9.9.121.1.1.5 cncNcdpMessageInterval 1 1 The interval at which NCDP configuration PDUs are to be
    generated.

    The message interval directly affects the convergence time
    of t…
    1.3.6.1.4.1.9.9.121.1.1.7 cncSourceChangeReason 1 1 The reason for the most recent change of a source of
    network clock, as indicated by the change in the value
    of cncSourceChangeTim…
    1.3.6.1.4.1.9.9.121.1.1.8 cncSourceChangeTimeStamp 1 1 The value of sysUpTime when the most recent change of a
    source of network clock occurred.

    A value of 0 indicates that no such eve…
    1.3.6.1.4.1.9.9.121.1.1.9 cncRootClockSource 1 1 The entPhysicalIndex of the network clock source that is
    actively supplying network clock within the device.