OID reference

sIfMauMediaAvailable

1.3.6.1.4.1.13464.1.2.2.2.6.2.1.1.5

Description

If the MAU is a link or fiber type (FOIRL, 10BASE-T, 10BASE-F) then this is equivalent to the link test fail state/low light function. For an AUI or a coax (including broadband) MAU this indicates whether or not loopback is detected on the DI circuit. The value of this attribute persists between packets for MAU types …

Full description and source information

Identification

Identifier and names

Parent
1.3.6.1.4.1.13464.1.2.2.2.6.2.1.1 (sIfMauEntry)
Node code
5
Node name
sIfMauMediaAvailable
Category
SNMP management object
Numeric OID
1.3.6.1.4.1.13464.1.2.2.2.6.2.1.1.5
URN notation
urn:oid:1.3.6.1.4.1.13464.1.2.2.2.6.2.1.1.5
ASN.1, OID-IRI and named path variants
ASN.1 notation

{1 3 6 1 4 1 13464 1 2 2 2 6 2 1 1 5}

  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) enterprise(1) admin(13464) dataCom(1) gbn(2) gbnDevice(2) bcmSwapi(2) sRFC2239MIB(6) sDot3IfMauBasicGroup(2) sIfMauTable(1) sIfMauEntry(1) sIfMauMediaAvailable(5)}
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) enterprise(1) admin(13464) datacom(1) gbn(2) gbnDevice(2) bcmSwapi(2) sRFC2239MIB(6) sDot3IfMauBasicGroup(2) sIfMauTable(1) sIfMauEntry(1) sIfMauMediaAvailable(5)}
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) enterprise(1) greentech(13464) dataCom(1) gbn(2) gbnDevice(2) bcmSwapi(2) sRFC2239MIB(6) sDot3IfMauBasicGroup(2) sIfMauTable(1) sIfMauEntry(1) sIfMauMediaAvailable(5)}
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) enterprise(1) greentech(13464) datacom(1) gbn(2) gbnDevice(2) bcmSwapi(2) sRFC2239MIB(6) sDot3IfMauBasicGroup(2) sIfMauTable(1) sIfMauEntry(1) sIfMauMediaAvailable(5)}
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) enterprises(1) admin(13464) dataCom(1) gbn(2) gbnDevice(2) bcmSwapi(2) sRFC2239MIB(6) sDot3IfMauBasicGroup(2) sIfMauTable(1) sIfMauEntry(1) sIfMauMediaAvailable(5)}
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) enterprises(1) admin(13464) datacom(1) gbn(2) gbnDevice(2) bcmSwapi(2) sRFC2239MIB(6) sDot3IfMauBasicGroup(2) sIfMauTable(1) sIfMauEntry(1) sIfMauMediaAvailable(5)}
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) enterprises(1) greentech(13464) dataCom(1) gbn(2) gbnDevice(2) bcmSwapi(2) sRFC2239MIB(6) sDot3IfMauBasicGroup(2) sIfMauTable(1) sIfMauEntry(1) sIfMauMediaAvailable(5)}
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) enterprises(1) greentech(13464) datacom(1) gbn(2) gbnDevice(2) bcmSwapi(2) sRFC2239MIB(6) sDot3IfMauBasicGroup(2) sIfMauTable(1) sIfMauEntry(1) sIfMauMediaAvailable(5)}
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) ldap-enterprise(1) admin(13464) dataCom(1) gbn(2) gbnDevice(2) bcmSwapi(2) sRFC2239MIB(6) sDot3IfMauBasicGroup(2) sIfMauTable(1) sIfMauEntry(1) sIfMauMediaAvailable(5)}
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) ldap-enterprise(1) admin(13464) datacom(1) gbn(2) gbnDevice(2) bcmSwapi(2) sRFC2239MIB(6) sDot3IfMauBasicGroup(2) sIfMauTable(1) sIfMauEntry(1) sIfMauMediaAvailable(5)}
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) ldap-enterprise(1) greentech(13464) dataCom(1) gbn(2) gbnDevice(2) bcmSwapi(2) sRFC2239MIB(6) sDot3IfMauBasicGroup(2) sIfMauTable(1) sIfMauEntry(1) sIfMauMediaAvailable(5)}
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) ldap-enterprise(1) greentech(13464) datacom(1) gbn(2) gbnDevice(2) bcmSwapi(2) sRFC2239MIB(6) sDot3IfMauBasicGroup(2) sIfMauTable(1) sIfMauEntry(1) sIfMauMediaAvailable(5)}
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) vendor-objects(1) admin(13464) dataCom(1) gbn(2) gbnDevice(2) bcmSwapi(2) sRFC2239MIB(6) sDot3IfMauBasicGroup(2) sIfMauTable(1) sIfMauEntry(1) sIfMauMediaAvailable(5)}
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) vendor-objects(1) admin(13464) datacom(1) gbn(2) gbnDevice(2) bcmSwapi(2) sRFC2239MIB(6) sDot3IfMauBasicGroup(2) sIfMauTable(1) sIfMauEntry(1) sIfMauMediaAvailable(5)}
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) vendor-objects(1) greentech(13464) dataCom(1) gbn(2) gbnDevice(2) bcmSwapi(2) sRFC2239MIB(6) sDot3IfMauBasicGroup(2) sIfMauTable(1) sIfMauEntry(1) sIfMauMediaAvailable(5)}
  • {iso(1) identified-organization(3) dod(6) internet(1) private(4) vendor-objects(1) greentech(13464) datacom(1) gbn(2) gbnDevice(2) bcmSwapi(2) sRFC2239MIB(6) sDot3IfMauBasicGroup(2) sIfMauTable(1) sIfMauEntry(1) sIfMauMediaAvailable(5)}
  • Additional combinations skipped.
OID-IRI notation
  • /1/3/6/1/4/1/13464/1/2/2/2/6/2/1/1/5
  • /ISO/Identified-Organization/6/1/4/1/13464/1/2/2/2/6/2/1/1/5
  • /ISO/3/6/1/4/1/13464/1/2/2/2/6/2/1/1/5
Named path variants
  • /iso/identified-organization/dod/internet/private/enterprise/13464/dataCom/gbn/gbnDevice/bcmSwapi/sRFC2239MIB/sDot3IfMauBasicGroup/sIfMauTable/sIfMauEntry/sIfMauMediaAvailable
  • /iso/identified-organization/dod/internet/private/enterprise/13464/datacom/gbn/gbnDevice/bcmSwapi/sRFC2239MIB/sDot3IfMauBasicGroup/sIfMauTable/sIfMauEntry/sIfMauMediaAvailable
  • /iso/identified-organization/dod/internet/private/enterprise/admin/dataCom/gbn/gbnDevice/bcmSwapi/sRFC2239MIB/sDot3IfMauBasicGroup/sIfMauTable/sIfMauEntry/sIfMauMediaAvailable
  • /iso/identified-organization/dod/internet/private/enterprise/admin/datacom/gbn/gbnDevice/bcmSwapi/sRFC2239MIB/sDot3IfMauBasicGroup/sIfMauTable/sIfMauEntry/sIfMauMediaAvailable
  • /iso/identified-organization/dod/internet/private/enterprise/greentech/dataCom/gbn/gbnDevice/bcmSwapi/sRFC2239MIB/sDot3IfMauBasicGroup/sIfMauTable/sIfMauEntry/sIfMauMediaAvailable
  • /iso/identified-organization/dod/internet/private/enterprise/greentech/datacom/gbn/gbnDevice/bcmSwapi/sRFC2239MIB/sDot3IfMauBasicGroup/sIfMauTable/sIfMauEntry/sIfMauMediaAvailable
  • /iso/identified-organization/dod/internet/private/enterprises/13464/dataCom/gbn/gbnDevice/bcmSwapi/sRFC2239MIB/sDot3IfMauBasicGroup/sIfMauTable/sIfMauEntry/sIfMauMediaAvailable
  • /iso/identified-organization/dod/internet/private/enterprises/13464/datacom/gbn/gbnDevice/bcmSwapi/sRFC2239MIB/sDot3IfMauBasicGroup/sIfMauTable/sIfMauEntry/sIfMauMediaAvailable
  • /iso/identified-organization/dod/internet/private/enterprises/admin/dataCom/gbn/gbnDevice/bcmSwapi/sRFC2239MIB/sDot3IfMauBasicGroup/sIfMauTable/sIfMauEntry/sIfMauMediaAvailable
  • /iso/identified-organization/dod/internet/private/enterprises/admin/datacom/gbn/gbnDevice/bcmSwapi/sRFC2239MIB/sDot3IfMauBasicGroup/sIfMauTable/sIfMauEntry/sIfMauMediaAvailable
  • /iso/identified-organization/dod/internet/private/enterprises/greentech/dataCom/gbn/gbnDevice/bcmSwapi/sRFC2239MIB/sDot3IfMauBasicGroup/sIfMauTable/sIfMauEntry/sIfMauMediaAvailable
  • /iso/identified-organization/dod/internet/private/enterprises/greentech/datacom/gbn/gbnDevice/bcmSwapi/sRFC2239MIB/sDot3IfMauBasicGroup/sIfMauTable/sIfMauEntry/sIfMauMediaAvailable
  • /iso/identified-organization/dod/internet/private/ldap-enterprise/13464/dataCom/gbn/gbnDevice/bcmSwapi/sRFC2239MIB/sDot3IfMauBasicGroup/sIfMauTable/sIfMauEntry/sIfMauMediaAvailable
  • /iso/identified-organization/dod/internet/private/ldap-enterprise/13464/datacom/gbn/gbnDevice/bcmSwapi/sRFC2239MIB/sDot3IfMauBasicGroup/sIfMauTable/sIfMauEntry/sIfMauMediaAvailable
  • /iso/identified-organization/dod/internet/private/ldap-enterprise/admin/dataCom/gbn/gbnDevice/bcmSwapi/sRFC2239MIB/sDot3IfMauBasicGroup/sIfMauTable/sIfMauEntry/sIfMauMediaAvailable
  • /iso/identified-organization/dod/internet/private/ldap-enterprise/admin/datacom/gbn/gbnDevice/bcmSwapi/sRFC2239MIB/sDot3IfMauBasicGroup/sIfMauTable/sIfMauEntry/sIfMauMediaAvailable
  • Additional combinations skipped.

SNMP properties

Value type
INTEGER
Maximum access defined by MIB
read-only
Status in MIB
current

Enumerated values

ValueName
1other
2unknown
3available
4notAvailable
5remoteFault
6invalidSignal
7remoteJabber
8remoteLinkLoss
9remoteTest
10offline
11autoNegError

Using this OID with SNMP

At least one MIB declaration places this object in a table row. A value belongs to a row instance; its suffix depends on the row's INDEX or AUGMENTS definition.

In GBNDeviceSWAPI-MIB, the row index sIfMauIndex is declared as Integer32. A non-negative index value is encoded as one numeric subidentifier. An instance has the form .1.3.6.1.4.1.13464.1.2.2.2.6.2.1.1.5.<sIfMauIndex>. Use an index value actually present on the device and permitted by its MIB. Other definitions can differ.

snmpwalk [connection options] DEVICE .1.3.6.1.4.1.13464.1.2.2.2.6.2.1.1.5

Replace the placeholders with your connection and authentication options. Available permissions and device support can differ from the MIB.

Properties come from available MIB definitions. Actual device support and access can differ. See source records below for original files and qualifications.

The displayed source records contain one distinct definition. Compare its source records.

sIfMauMediaAvailable OBJECT-TYPE
       SYNTAX     INTEGER {
                      other(1),
                      unknown(2),
                      available(3),
                      notAvailable(4),
                      remoteFault(5),
                      invalidSignal(6),
                      remoteJabber(7),
                      remoteLinkLoss(8),
                      remoteTest(9),
                      offline(10),
                      autoNegError(11)

                  }
       MAX-ACCESS read-only
       STATUS     current
           DESCRIPTION "If the MAU is a link or fiber type (FOIRL,
                       10BASE-T, 10BASE-F) then this is equivalent to
                       the link test fail state/low light function.
                       For an AUI or a coax (including broadband) MAU
                       this indicates whether or not loopback is
                       detected on the DI circuit.  The value of this
                       attribute persists between packets for MAU types
                       AUI, 10BASE5, 10BASE2, 10BROAD36, and 10BASE-FP.

                       The value other(1) is returned if the
                       mediaAvailable state is not one of 2 through 11.
                       The value unknown(2) is returned when the MAU's
                       true state is unknown; for example, when it is
                       being initialized.  At power-up or following a
                       reset, the value of this attribute will be
                       unknown for AUI, coax, and 10BASE-FP MAUs.  For
                       these MAUs loopback will be tested on each
                       transmission during which no collision is
                       detected.  If DI is receiving input when DO
                       returns to IDL after a transmission and there
                       has been no collision during the transmission
                       then loopback will be detected.  The value of
                       this attribute will only change during
                       non-collided transmissions for AUI, coax, and
                       10BASE-FP MAUs.

                       For 100Mbps and 1000Mbps MAUs, the enumerations
                       match the states within the respective link
                       integrity state diagrams, fig 32-16, 23-12 and
                       24-15 of sections 32, 23 and 24 of [2].  Any MAU
                       which implements management of auto-negotiation
                       will map remote fault indication to remote
                       fault.

                       The value available(3) indicates that the link,
                       light, or loopback is normal.  The value
                       notAvailable(4) indicates link loss, low light,
                       or no loopback.

                       The value remoteFault(5) indicates that a fault
                       has been detected at the remote end of the link.
                       This value applies to 10BASE-FB, 100BASE-T4 Far
                       End Fault Indication and non-specified remote
                       faults from a system running auto-negotiation.
                       The values remoteJabber(7), remoteLinkLoss(8),
                       and remoteTest(9) SHOULD be used instead of
                       remoteFault(5) where the reason for remote fault
                       is identified in the remote signaling protocol.

                       The value invalidSignal(6) indicates that an
                       invalid signal has been received from the other
                       end of the link.  InvalidSignal(6) applies only
                       to MAUs of type 10BASE-FB.

                       Where an IEEE Std 802.3u-1995 clause 22 MII
                       is present, a logic one in the remote fault bit
                       (reference section 22.2.4.2.8 of that document)
                       maps to the value remoteFault(5), and a logic
                       zero in the link status bit (reference section
                       22.2.4.2.10 of that document) maps to the value
                       notAvailable(4).  The value notAvailable(4)
                       takes precedence over the value remoteFault(5).

                       Any MAU that implements management of clause 37
                       Auto-Negotiation will map the received RF1 and
                       RF2 bit values for Offline to offline(10), Link
                       Failure to remoteFault(5) and Auto-Negotiation
                       Error to autoNegError(11)."

       REFERENCE
               "[IEEE 802.3 Mgt], 30.5.1.1.4, aMediaAvailable."
       ::= { sIfMauEntry 5 }

Meaning

Descriptions

1 unique

Identical descriptions are grouped. Different wording and device-specific notes are retained.

If the MAU is a link or fiber type (FOIRL, 10BASE-T, 10BASE-F) then this is equivalent to the link test fail state/low light function. For an AUI or a coax (including broadband) MAU this indicates whether or not loopback is detected on the DI circuit. The value of this attribute persists between packets for MAU types AUI, 10BASE5, 10BASE2, 10BROAD36, and 10BASE-FP. The value other(1) is returned if the mediaAvailable state is not one of 2 through 11. The value unknown(2) is returned when the MAU's true state is unknown; for example, when it is being initialized. At power-up or following a reset, the value of this attribute will be unknown for AUI, coax, and 10BASE-FP MAUs. For these MAUs loopback will be tested on each transmission during which no collision is detected. If DI is receiving input when DO returns to IDL after a transmission and there has been no collision during the transmission then loopback will be detected. The value of this attribute will only change during non-collided transmissions for AUI, coax, and 10BASE-FP MAUs. For 100Mbps and 1000Mbps MAUs, the enumerations match the states within the respective link integrity state diagrams, fig 32-16, 23-12 and 24-15 of sections 32, 23 and 24 of [2]. Any MAU which implements management of auto-negotiation will map remote fault indication to remote fault. The value available(3) indicates that the link, light, or loopback is normal. The value notAvailable(4) indicates link loss, low light, or no loopback. The value remoteFault(5) indicates that a fault has been detected at the remote end of the link. This value applies to 10BASE-FB, 100BASE-T4 Far End Fault Indication and non-specified remote faults from a system running auto-negotiation. The values remoteJabber(7), remoteLinkLoss(8), and remoteTest(9) SHOULD be used instead of remoteFault(5) where the reason for remote fault is identified in the remote signaling protocol. The value invalidSignal(6) indicates that an invalid signal has been received from the other end of the link. InvalidSignal(6) applies only to MAUs of type 10BASE-FB. Where an IEEE Std 802.3u-1995 clause 22 MII is present, a logic one in the remote fault bit (reference section 22.2.4.2.8 of that document) maps to the value remoteFault(5), and a logic zero in the link status bit (reference section 22.2.4.2.10 of that document) maps to the value notAvailable(4). The value notAvailable(4) takes precedence over the value remoteFault(5). Any MAU that implements management of clause 37 Auto-Negotiation will map the received RF1 and RF2 bit values for Offline to offline(10), Link Failure to remoteFault(5) and Auto-Negotiation Error to autoNegError(11).

Sources for this description

Multiple manufacturers; see the original MIB MIB copies (LibreNMS/Observium Community)FS.COM MIB copies (LibreNMS/Observium Community)

See 1 matching source record

Evidence

Source records

1 records

Matching descriptions are grouped; open a group to compare definitions and supporting files.

Records for description 1Multiple manufacturers; see the original MIB MIB copies (LibreNMS/Observium Community), FS.COM MIB copies (LibreNMS/Observium Community)1 record · 3 sources

Description 1

sIfMauMediaAvailable · currentMultiple manufacturers; see the original MIB MIB copies (LibreNMS/Observium Community), FS.COM MIB copies (LibreNMS/Observium Community)3 sources

Status in source: current.

Names: sIfMauMediaAvailable

Technical details
{
  "smi_kind": "OBJECT-TYPE",
  "definition": [
    "sIfMauMediaAvailable",
    "OBJECT-TYPE",
    "SYNTAX",
    "INTEGER",
    "{",
    "other",
    "(",
    "1",
    ")",
    ",",
    "unknown",
    "(",
    "2",
    ")",
    ",",
    "available",
    "(",
    "3",
    ")",
    ",",
    "notAvailable",
    "(",
    "4",
    ")",
    ",",
    "remoteFault",
    "(",
    "5",
    ")",
    ",",
    "invalidSignal",
    "(",
    "6",
    ")",
    ",",
    "remoteJabber",
    "(",
    "7",
    ")",
    ",",
    "remoteLinkLoss",
    "(",
    "8",
    ")",
    ",",
    "remoteTest",
    "(",
    "9",
    ")",
    ",",
    "offline",
    "(",
    "10",
    ")",
    ",",
    "autoNegError",
    "(",
    "11",
    ")",
    "}",
    "MAX-ACCESS",
    "read-only",
    "STATUS",
    "current",
    "DESCRIPTION",
    "\"If the MAU is a link or fiber type (FOIRL, 10BASE-T, 10BASE-F) then this is equivalent to the link test fail state/low light function. For an AUI or a coax (including broadband) MAU this indicates whether or not loopback is detected on the DI circuit. The value of this attribute persists between packets for MAU types AUI, 10BASE5, 10BASE2, 10BROAD36, and 10BASE-FP. The value other(1) is returned if the mediaAvailable state is not one of 2 through 11. The value unknown(2) is returned when the MAU's true state is unknown; for example, when it is being initialized. At power-up or following a reset, the value of this attribute will be unknown for AUI, coax, and 10BASE-FP MAUs. For these MAUs loopback will be tested on each transmission during which no collision is detected. If DI is receiving input when DO returns to IDL after a transmission and there has been no collision during the transmission then loopback will be detected. The value of this attribute will only change during non-collided transmissions for AUI, coax, and 10BASE-FP MAUs. For 100Mbps and 1000Mbps MAUs, the enumerations match the states within the respective link integrity state diagrams, fig 32-16, 23-12 and 24-15 of sections 32, 23 and 24 of [2]. Any MAU which implements management of auto-negotiation will map remote fault indication to remote fault. The value available(3) indicates that the link, light, or loopback is normal. The value notAvailable(4) indicates link loss, low light, or no loopback. The value remoteFault(5) indicates that a fault has been detected at the remote end of the link. This value applies to 10BASE-FB, 100BASE-T4 Far End Fault Indication and non-specified remote faults from a system running auto-negotiation. The values remoteJabber(7), remoteLinkLoss(8), and remoteTest(9) SHOULD be used instead of remoteFault(5) where the reason for remote fault is identified in the remote signaling protocol. The value invalidSignal(6) indicates that an invalid signal has been received from the other end of the link. InvalidSignal(6) applies only to MAUs of type 10BASE-FB. Where an IEEE Std 802.3u-1995 clause 22 MII is present, a logic one in the remote fault bit (reference section 22.2.4.2.8 of that document) maps to the value remoteFault(5), and a logic zero in the link status bit (reference section 22.2.4.2.10 of that document) maps to the value notAvailable(4). The value notAvailable(4) takes precedence over the value remoteFault(5). Any MAU that implements management of clause 37 Auto-Negotiation will map the received RF1 and RF2 bit values for Offline to offline(10), Link Failure to remoteFault(5) and Auto-Negotiation Error to autoNegError(11).\"",
    "REFERENCE",
    "\"[IEEE 802.3 Mgt], 30.5.1.1.4, aMediaAvailable.\"",
    "::=",
    "{",
    "sIfMauEntry",
    "5",
    "}"
  ],
  "syntax_tree": [
    [
      "SimpleSyntax",
      "INTEGER",
      [
        "enumSpec",
        [
          [
            "other",
            1
          ],
          [
            "unknown",
            2
          ],
          [
            "available",
            3
          ],
          [
            "notAvailable",
            4
          ],
          [
            "remoteFault",
            5
          ],
          [
            "invalidSignal",
            6
          ],
          [
            "remoteJabber",
            7
          ],
          [
            "remoteLinkLoss",
            8
          ],
          [
            "remoteTest",
            9
          ],
          [
            "offline",
            10
          ],
          [
            "autoNegError",
            11
          ]
        ]
      ]
    ],
    null,
    [
      "MaxAccessPart",
      "read-only"
    ],
    [
      "Status",
      "current"
    ],
    [
      "DESCRIPTION",
      "If the MAU is a link or fiber type (FOIRL, 10BASE-T, 10BASE-F) then this is equivalent to the link test fail state/low light function. For an AUI or a coax (including broadband) MAU this indicates whether or not loopback is detected on the DI circuit. The value of this attribute persists between packets for MAU types AUI, 10BASE5, 10BASE2, 10BROAD36, and 10BASE-FP. The value other(1) is returned if the mediaAvailable state is not one of 2 through 11. The value unknown(2) is returned when the MAU's true state is unknown; for example, when it is being initialized. At power-up or following a reset, the value of this attribute will be unknown for AUI, coax, and 10BASE-FP MAUs. For these MAUs loopback will be tested on each transmission during which no collision is detected. If DI is receiving input when DO returns to IDL after a transmission and there has been no collision during the transmission then loopback will be detected. The value of this attribute will only change during non-collided transmissions for AUI, coax, and 10BASE-FP MAUs. For 100Mbps and 1000Mbps MAUs, the enumerations match the states within the respective link integrity state diagrams, fig 32-16, 23-12 and 24-15 of sections 32, 23 and 24 of [2]. Any MAU which implements management of auto-negotiation will map remote fault indication to remote fault. The value available(3) indicates that the link, light, or loopback is normal. The value notAvailable(4) indicates link loss, low light, or no loopback. The value remoteFault(5) indicates that a fault has been detected at the remote end of the link. This value applies to 10BASE-FB, 100BASE-T4 Far End Fault Indication and non-specified remote faults from a system running auto-negotiation. The values remoteJabber(7), remoteLinkLoss(8), and remoteTest(9) SHOULD be used instead of remoteFault(5) where the reason for remote fault is identified in the remote signaling protocol. The value invalidSignal(6) indicates that an invalid signal has been received from the other end of the link. InvalidSignal(6) applies only to MAUs of type 10BASE-FB. Where an IEEE Std 802.3u-1995 clause 22 MII is present, a logic one in the remote fault bit (reference section 22.2.4.2.8 of that document) maps to the value remoteFault(5), and a logic zero in the link status bit (reference section 22.2.4.2.10 of that document) maps to the value notAvailable(4). The value notAvailable(4) takes precedence over the value remoteFault(5). Any MAU that implements management of clause 37 Auto-Negotiation will map the received RF1 and RF2 bit values for Offline to offline(10), Link Failure to remoteFault(5) and Auto-Negotiation Error to autoNegError(11)."
    ],
    [
      "REFERENCE",
      "[IEEE 802.3 Mgt], 30.5.1.1.4, aMediaAvailable."
    ],
    null,
    null,
    null
  ]
}

Registration

Registration authorities

First Registration Authority (inferred from ancestor 1.3.6.1.4.1.13464)

Ke Qin

Siblings (4)

OIDNameDirect childrenDescendantsDescription
1.3.6.1.4.1.13464.1.2.2.2.6.2.1.1.2 sIfMauIndex00
1.3.6.1.4.1.13464.1.2.2.2.6.2.1.1.3 sIfMauType00
1.3.6.1.4.1.13464.1.2.2.2.6.2.1.1.7 sIfMauJabberState00
1.3.6.1.4.1.13464.1.2.2.2.6.2.1.1.11 sIfMauDefaultType00