| 1.3.6.1.4.1.2272.1.4.10.1.1.1 |
rcPortIndex | 0 | 0 |
An index value that uniquely identifies a port. This value is similar to ifIndex in MIB2. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.2 |
rcPortType | 0 | 0 |
Port type |
| 1.3.6.1.4.1.2272.1.4.10.1.1.3 |
rcPortConnectorType | 0 | 0 |
Type of connector installed on this port. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.4 |
rcPortPerformRouting | 0 | 0 |
Indicate whether this port should perform routing |
| 1.3.6.1.4.1.2272.1.4.10.1.1.5 |
rcPortHighPriority | 0 | 0 |
Indicate whether this port should be treated with high priority |
| 1.3.6.1.4.1.2272.1.4.10.1.1.6 |
rcPortAction | 0 | 0 |
Port related actions. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.7 |
rcPortResult | 0 | 0 |
Result from the last Vlan action. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.8 |
rcPortPrimaryConnector | 0 | 0 |
For ports configured with redundant connectors, this value is used to indicate which connector should be used as the 'active' con… |
| 1.3.6.1.4.1.2272.1.4.10.1.1.9 |
rcPortActiveConnector | 0 | 0 |
For ports configured with redundant connectors, this value is used to indicate which connector is currently the active one. Only… |
| 1.3.6.1.4.1.2272.1.4.10.1.1.10 |
rcPortBackupConnectorStatus | 0 | 0 |
Indicate the status of the link attached to the back-up (non-active) connector. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.11 |
rcPortAutoNegotiate | 0 | 0 |
Indicate whether this port enabled for auto negotiations or not. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.13 |
rcPortOperDuplex | 0 | 0 |
Indicate this port's current duplex value. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.14 |
rcPortAdminSpeed | 0 | 0 |
Indicate this port's speed. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.15 |
rcPortOperSpeed | 0 | 0 |
Indicate this port's current speed value. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.16 |
rcPortMltId | 0 | 0 |
Indicate which multi-link trunk (MLT) this port is assigned to. If this port is not associated with any MLT, this value will be … |
| 1.3.6.1.4.1.2272.1.4.10.1.1.17 |
rcPortLocked | 0 | 0 |
Indicate whether this port is locked. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.18 |
rcPortAutoNegotiationSupported | 0 | 0 |
Indicate whether this port can support auto-negotiation. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.19 |
rcPortSingleRoutablePort | 0 | 0 |
Indicate whether this port is a single routable port. If this value is true, the port functions like a traditional router port. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.20 |
rcPortUnknownMacDiscard | 0 | 0 |
If rcUnknownMacDiscard is set to True, then a packet with an unknown source MAC address is dropped on that port, and other ports … |
| 1.3.6.1.4.1.2272.1.4.10.1.1.21 |
rcPortNumStateTransition | 0 | 0 |
# state transitions. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.22 |
rcPortUserPriority | 0 | 0 |
User priority level. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.23 |
rcPortAllowOversizeFrame | 0 | 0 |
Used to specify whether over-size frames should be processed or dropped. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.30 |
rcPortQosLevel | 0 | 0 |
Used to specify the Qos level packets, carried on this port, should be processed with. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.31 |
rcPortDiffServEnable | 0 | 0 |
Used to enable/disable the Differentiated Service feature on this port. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.32 |
rcPortDiffServType | 0 | 0 |
Used to specify the Differentiated Service type for this port. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.33 |
rcPortDiffServIeee8021POverrideEnable | 0 | 0 |
Used to enable/disable the Differentiated Service IEEE 802.1P over-ride feature. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.34 |
rcPortVendorDescr | 0 | 0 |
Used to show the name of the vendor of this port's connector. Only applicable to ports on a GBIC cards. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.35 |
rcPortName | 0 | 0 |
This port's name. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.36 |
rcPortOctapidId | 0 | 0 |
The octapid id of the mirrored port. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.37 |
rcPortWan | 0 | 0 |
Indicatie this port's current WAN/LAN mode. Valid for 10 GE only |
| 1.3.6.1.4.1.2272.1.4.10.1.1.38 |
rcPortTransport | 0 | 0 |
Indicatie this port's current tranport layer. Valid for 10 GE only |
| 1.3.6.1.4.1.2272.1.4.10.1.1.39 |
rcPortMultimediaFilterEnable | 0 | 0 |
Used to enable/disable the Telephony device selected on this port |
| 1.3.6.1.4.1.2272.1.4.10.1.1.40 |
rcPortMultimediaDevSelection | 0 | 0 |
Used to set/get the selected Multimedia & Telephony Devices on this port. The String is the name of the device in the rcIpFilterMe… |
| 1.3.6.1.4.1.2272.1.4.10.1.1.41 |
rcPortServiceType | 0 | 0 |
Indicates the port functionality. 12uni is used to configure the port to be part of Martini service, tls is used to configure the… |
| 1.3.6.1.4.1.2272.1.4.10.1.1.42 |
rcPortMode | 0 | 0 |
The port mode for l2uni service type.If the port is configured for l2uni service type, then the mode can be transparent or switch… |
| 1.3.6.1.4.1.2272.1.4.10.1.1.43 |
rcPortAdminRouting | 0 | 0 |
Indicate whether the port is routable. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.44 |
rcPortOperRouting | 0 | 0 |
The status of the port whether is routable. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.45 |
rcPortPid | 0 | 0 |
The pid of the mirrored port. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.46 |
rcPortIeee8021POverrideEnable | 0 | 0 |
Used to enable/disable IEEE 802.1P override. If it is enabled, 802.1p vlaue from a tagged frame may not honor. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.47 |
rcPortShaperEnable | 0 | 0 |
Used to enable/disable shaper on the port. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.48 |
rcPortShaperMaxRate | 0 | 0 |
Shaping rate in mega bits per second. Note that actual shaping rate might be different from the configured rate due to the rate g… |
| 1.3.6.1.4.1.2272.1.4.10.1.1.49 |
rcPortShaperBurstSize | 0 | 0 |
Burst size in kilo bytes per second. Note that actual burst size might be different from the configured size due to the granular… |
| 1.3.6.1.4.1.2272.1.4.10.1.1.50 |
rcPortCpLimitShutDown | 0 | 0 |
A TRUE value indicates if CP Limit shut down the interface. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.51 |
rcPortHighSecureEnable | 0 | 0 |
Enable/Disable high secure. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.52 |
rcPortTlsPriorityOverride | 0 | 0 |
Enable/Disable tls port priority override feature. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.53 |
rcPortVctAbility | 0 | 0 |
If this object is TRUE, then the specified port is hardware-capable of doing the VCT test, if the rcPortAdminStatus is also true.… |
| 1.3.6.1.4.1.2272.1.4.10.1.1.54 |
rcPortVctAdminStatus | 0 | 0 |
Admin status for port VCT test. If this object is set to TRUE, then the VCT test can be performed. If it is set to FALSE, then th… |
| 1.3.6.1.4.1.2272.1.4.10.1.1.55 |
rcPortMrouteStrLimit | 0 | 0 |
maximum number of multicast streams that are allowed to ingress to CPU through this port. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.56 |
rcPortMrouteStrTimerCheck | 0 | 0 |
sampling period to check number of multicast streams that has ingressed CPU through this port. |
| 1.3.6.1.4.1.2272.1.4.10.1.1.57 |
rcPortMrouteStrLimitEnable | 0 | 0 |
enable or disable mroute stream limit on port. |