{1 3 6 1 4 1 232 0 13601592}
Severity: Normal -- informational in nature. A Fibre Channel physical disk drive firmware revision has been detected by the physical disk drive firmware load process that has a newer supported revision available.
Severity: Normal -- informational in nature. A Fibre Channel physical disk drive firmware revision has been detected by the physical disk drive firmware load process that has a newer supported revision available. If the location information is 0, it indicates the type of drive, not a specific drive. The identity of the physical disk drive is contained in the device field. The Fibre Channel port used to communicate with the physical disk drive is contained in the cerp_id field. The HSV110 controller internal Fibre Channel port number used to communicate with the physical disk drive is contained in the port field. The arbitrated loop physical address of the physical disk drive is contained in the al_pa field. The bypass_reason field is invalid. The location of the physical disk drive is determined by the content of the dencl_num field as follows: <UL><LI>If dencl_num is less than 99, the location is as indicated by the content of the rack_num, dencl_num, and bay fields. <LI>If dencl_num is equal to 99, the location is unknown. Note that the content of the rack_num, al_pa and bay fields is undefined in this case. <LI>If dencl_num is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rack_num, dencl_num, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. </UL>Note that the content of the rack_num field will not be valid until a future release. The pid field contains the SCSI Inquiry Product Identification obtained from the physical disk drive. The rev field contains the current firmware revision obtained from the physical disk drive. The new_rev field contains the latest firmware version known to the controller, or blanks if the isn't a known version. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerp_id field. The location of an available drive enclosure is determined by the content of the enclosures.dencl_num field as follows: <UL><LI>If enclosures.dencl_num is less than 99, the location is as indicated by the content of the enclosures.rack_num and enclosures.dencl_num fields. <LI>If enclosures.dencl_num is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rack_num field is undefined in this case. <LI>If enclosures.dencl_num is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rack_num and enclosures.dencl_num fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. </UL>Note that the content of the enclosures.rack_num field will not be valid until a future release.
Status in source: unspecified.
Names: sCellEventTrap-06-38
{
"smi_kind": "TRAP-TYPE",
"definition": [
"sCellEventTrap-06-38",
"TRAP-TYPE",
"ENTERPRISE",
"compaq",
"VARIABLES",
"{",
"scellNameDateTime",
",",
"scellSWComponent",
",",
"scellECode",
",",
"scellCAC",
",",
"scellEIP",
"}",
"DESCRIPTION",
"\"Severity: Normal -- informational in nature. A Fibre Channel physical disk drive firmware revision has been detected by the physical disk drive firmware load process that has a newer supported revision available.\"",
"::=",
"13601592"
],
"syntax_tree": [
[
"objectIdentifier",
[
"compaq"
]
],
[
"VarTypes",
[
"scellNameDateTime",
"scellSWComponent",
"scellECode",
"scellCAC",
"scellEIP"
]
],
[
"DESCRIPTION",
"Severity: Normal -- informational in nature. A Fibre Channel physical disk drive firmware revision has been detected by the physical disk drive firmware load process that has a newer supported revision available."
],
null
]
}Module: CPQHSV-MIB
sCellEventTrap-06-38 TRAP-TYPE -- CAC Code: c4
ENTERPRISE compaq
VARIABLES { scellNameDateTime,
scellSWComponent,
scellECode,
scellCAC,
scellEIP}
DESCRIPTION
"Severity: Normal -- informational in nature. A Fibre Channel physical disk drive firmware revision has been detected by the physical disk drive firmware load process that has a newer supported revision available."
--#TYPE "StorageCell Event"
--#SUMMARY "SCellName-TimeDate %s : SWCID %d : ECode: %d : CAC %d : EIP %d."
--#ARGUMENTS {0,1,2,3,4,}
--#SEVERITY INFORMATIONAL
--#TIMEINDEX 136
--#STATE WARNING
::= 13601592{'RFC-1212': ['OBJECT-TYPE'], 'RFC-1215': ['TRAP-TYPE'], 'RFC1155-SMI': ['enterprises'], 'RFC1213-MIB': ['DisplayString']}Archived: 2026-10-19T00:22:16.773182+00:00.
Module: CPQHSV300V9-MIB
sCellEventTrap-06-38 TRAP-TYPE -- CAC Code: c4
ENTERPRISE compaq
VARIABLES { scellNameDateTime,
scellSWComponent,
scellECode,
scellCAC,
scellEIP}
DESCRIPTION
"Severity: Normal -- informational in nature. A Fibre Channel physical disk drive firmware revision has been detected by the physical disk drive firmware load process that has a newer supported revision available."
--#TYPE "StorageCell Event"
--#SUMMARY "SCellName-TimeDate %s : SWCID %d : ECode: %d : CAC %d : EIP %d."
--#ARGUMENTS {0,1,2,3,4,}
--#SEVERITY INFORMATIONAL
--#TIMEINDEX 136
--#STATE WARNING
::= 13601592{'RFC-1212': ['OBJECT-TYPE'], 'RFC-1215': ['TRAP-TYPE'], 'RFC1155-SMI': ['enterprises'], 'RFC1213-MIB': ['DisplayString']}Archived: 2026-10-19T00:22:08.878729+00:00.
Vendor MIB copy from the Observium Community archive. HPE networking support.
Module: CPQHSV-MIB
sCellEventTrap-06-38 TRAP-TYPE -- CAC Code: c4
ENTERPRISE compaq
VARIABLES { scellNameDateTime,
scellSWComponent,
scellECode,
scellCAC,
scellEIP}
DESCRIPTION
"Severity: Normal -- informational in nature. A Fibre Channel physical disk drive firmware revision has been detected by the physical disk drive firmware load process that has a newer supported revision available."
--#TYPE "StorageCell Event"
--#SUMMARY "SCellName-TimeDate %s : SWCID %d : ECode: %d : CAC %d : EIP %d."
--#ARGUMENTS {0,1,2,3,4,}
--#SEVERITY INFORMATIONAL
--#TIMEINDEX 136
--#STATE WARNING
::= 13601592{'RFC-1212': ['OBJECT-TYPE'], 'RFC-1215': ['TRAP-TYPE'], 'RFC1155-SMI': ['enterprises'], 'RFC1213-MIB': ['DisplayString']}Related source files and packages:
Downloaded: 2026-10-23T19:25:41.025282+00:00.
Status in source: unspecified.
Names: sCellEventTrap_6_38
{
"smi_kind": "TRAP-TYPE",
"definition": [
"sCellEventTrap_6_38",
"TRAP-TYPE",
"ENTERPRISE",
"compaq",
"VARIABLES",
"{",
"scellNameDateTime",
",",
"scellSWComponent",
",",
"scellECode",
",",
"scellCAC",
",",
"scellEIP",
"}",
"DESCRIPTION",
"\"Severity: Normal -- informational in nature. A Fibre Channel physical disk drive firmware revision has been detected by the physical disk drive firmware load process that has a newer supported revision available. If the location information is 0, it indicates the type of drive, not a specific drive. The identity of the physical disk drive is contained in the device field. The Fibre Channel port used to communicate with the physical disk drive is contained in the cerp_id field. The HSV110 controller internal Fibre Channel port number used to communicate with the physical disk drive is contained in the port field. The arbitrated loop physical address of the physical disk drive is contained in the al_pa field. The bypass_reason field is invalid. The location of the physical disk drive is determined by the content of the dencl_num field as follows: <UL><LI>If dencl_num is less than 99, the location is as indicated by the content of the rack_num, dencl_num, and bay fields. <LI>If dencl_num is equal to 99, the location is unknown. Note that the content of the rack_num, al_pa and bay fields is undefined in this case. <LI>If dencl_num is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rack_num, dencl_num, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. </UL>Note that the content of the rack_num field will not be valid until a future release. The pid field contains the SCSI Inquiry Product Identification obtained from the physical disk drive. The rev field contains the current firmware revision obtained from the physical disk drive. The new_rev field contains the latest firmware version known to the controller, or blanks if the isn't a known version. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerp_id field. The location of an available drive enclosure is determined by the content of the enclosures.dencl_num field as follows: <UL><LI>If enclosures.dencl_num is less than 99, the location is as indicated by the content of the enclosures.rack_num and enclosures.dencl_num fields. <LI>If enclosures.dencl_num is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rack_num field is undefined in this case. <LI>If enclosures.dencl_num is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rack_num and enclosures.dencl_num fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. </UL>Note that the content of the enclosures.rack_num field will not be valid until a future release.\"",
"::=",
"13601592"
],
"syntax_tree": [
[
"objectIdentifier",
[
"compaq"
]
],
[
"VarTypes",
[
"scellNameDateTime",
"scellSWComponent",
"scellECode",
"scellCAC",
"scellEIP"
]
],
[
"DESCRIPTION",
"Severity: Normal -- informational in nature. A Fibre Channel physical disk drive firmware revision has been detected by the physical disk drive firmware load process that has a newer supported revision available. If the location information is 0, it indicates the type of drive, not a specific drive. The identity of the physical disk drive is contained in the device field. The Fibre Channel port used to communicate with the physical disk drive is contained in the cerp_id field. The HSV110 controller internal Fibre Channel port number used to communicate with the physical disk drive is contained in the port field. The arbitrated loop physical address of the physical disk drive is contained in the al_pa field. The bypass_reason field is invalid. The location of the physical disk drive is determined by the content of the dencl_num field as follows: <UL><LI>If dencl_num is less than 99, the location is as indicated by the content of the rack_num, dencl_num, and bay fields. <LI>If dencl_num is equal to 99, the location is unknown. Note that the content of the rack_num, al_pa and bay fields is undefined in this case. <LI>If dencl_num is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rack_num, dencl_num, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. </UL>Note that the content of the rack_num field will not be valid until a future release. The pid field contains the SCSI Inquiry Product Identification obtained from the physical disk drive. The rev field contains the current firmware revision obtained from the physical disk drive. The new_rev field contains the latest firmware version known to the controller, or blanks if the isn't a known version. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerp_id field. The location of an available drive enclosure is determined by the content of the enclosures.dencl_num field as follows: <UL><LI>If enclosures.dencl_num is less than 99, the location is as indicated by the content of the enclosures.rack_num and enclosures.dencl_num fields. <LI>If enclosures.dencl_num is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rack_num field is undefined in this case. <LI>If enclosures.dencl_num is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rack_num and enclosures.dencl_num fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. </UL>Note that the content of the enclosures.rack_num field will not be valid until a future release."
],
null
]
}Module: CPQHSV110V3-MIB
sCellEventTrap_6_38 TRAP-TYPE -- CAC Code: c4
ENTERPRISE compaq
VARIABLES { scellNameDateTime,
scellSWComponent,
scellECode,
scellCAC,
scellEIP}
DESCRIPTION
"Severity: Normal -- informational in nature. A Fibre Channel physical disk drive firmware revision has been detected by the physical disk drive firmware load process that has a newer supported revision available. If the location information is 0, it indicates the type of drive, not a specific drive. The identity of the physical disk drive is contained in the device field. The Fibre Channel port used to communicate with the physical disk drive is contained in the cerp_id field. The HSV110 controller internal Fibre Channel port number used to communicate with the physical disk drive is contained in the port field. The arbitrated loop physical address of the physical disk drive is contained in the al_pa field. The bypass_reason field is invalid. The location of the physical disk drive is determined by the content of the dencl_num field as follows: <UL><LI>If dencl_num is less than 99, the location is as indicated by the content of the rack_num, dencl_num, and bay fields. <LI>If dencl_num is equal to 99, the location is unknown. Note that the content of the rack_num, al_pa and bay fields is undefined in this case. <LI>If dencl_num is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rack_num, dencl_num, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. </UL>Note that the content of the rack_num field will not be valid until a future release. The pid field contains the SCSI Inquiry Product Identification obtained from the physical disk drive. The rev field contains the current firmware revision obtained from the physical disk drive. The new_rev field contains the latest firmware version known to the controller, or blanks if the isn't a known version. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerp_id field. The location of an available drive enclosure is determined by the content of the enclosures.dencl_num field as follows: <UL><LI>If enclosures.dencl_num is less than 99, the location is as indicated by the content of the enclosures.rack_num and enclosures.dencl_num fields. <LI>If enclosures.dencl_num is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rack_num field is undefined in this case. <LI>If enclosures.dencl_num is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rack_num and enclosures.dencl_num fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. </UL>Note that the content of the enclosures.rack_num field will not be valid until a future release."
--#TYPE "StorageCell Event"
--#SUMMARY "SCellName-TimeDate %s : SWCID %d : ECode: %d : CAC %d : EIP %d."
--#ARGUMENTS {0,1,2,3,4,}
--#SEVERITY INFORMATIONAL
--#TIMEINDEX 136
--#STATE WARNING
::= 13601592{'RFC-1212': ['OBJECT-TYPE'], 'RFC-1215': ['TRAP-TYPE'], 'RFC1155-SMI': ['enterprises'], 'RFC1213-MIB': ['DisplayString']}Archived: 2026-10-19T00:22:08.860954+00:00.
Vendor MIB copy from the Observium Community archive. HPE networking support.
Module: CPQHSV110V3-MIB
sCellEventTrap_6_38 TRAP-TYPE -- CAC Code: c4
ENTERPRISE compaq
VARIABLES { scellNameDateTime,
scellSWComponent,
scellECode,
scellCAC,
scellEIP}
DESCRIPTION
"Severity: Normal -- informational in nature. A Fibre Channel physical disk drive firmware revision has been detected by the physical disk drive firmware load process that has a newer supported revision available. If the location information is 0, it indicates the type of drive, not a specific drive. The identity of the physical disk drive is contained in the device field. The Fibre Channel port used to communicate with the physical disk drive is contained in the cerp_id field. The HSV110 controller internal Fibre Channel port number used to communicate with the physical disk drive is contained in the port field. The arbitrated loop physical address of the physical disk drive is contained in the al_pa field. The bypass_reason field is invalid. The location of the physical disk drive is determined by the content of the dencl_num field as follows: <UL><LI>If dencl_num is less than 99, the location is as indicated by the content of the rack_num, dencl_num, and bay fields. <LI>If dencl_num is equal to 99, the location is unknown. Note that the content of the rack_num, al_pa and bay fields is undefined in this case. <LI>If dencl_num is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the rack_num, dencl_num, and bay fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. The identity contained in the device field should be used to confirm the last known location values. </UL>Note that the content of the rack_num field will not be valid until a future release. The pid field contains the SCSI Inquiry Product Identification obtained from the physical disk drive. The rev field contains the current firmware revision obtained from the physical disk drive. The new_rev field contains the latest firmware version known to the controller, or blanks if the isn't a known version. The enclosures array shows the drive enclosures available on the Fibre Channel port identified in the cerp_id field. The location of an available drive enclosure is determined by the content of the enclosures.dencl_num field as follows: <UL><LI>If enclosures.dencl_num is less than 99, the location is as indicated by the content of the enclosures.rack_num and enclosures.dencl_num fields. <LI>If enclosures.dencl_num is equal to 99, the enclosures array entry is not used. Note that the content of the enclosures.rack_num field is undefined in this case. <LI>If enclosures.dencl_num is greater than 99, the HSV110 controller does not have proof of the current location but the last known location is indicated by the content of the enclosures.rack_num and enclosures.dencl_num fields. Subtract 100 from the content of those fields to determine the actual last known location. If there have been no configuration changes, the last known location values will be accurate. </UL>Note that the content of the enclosures.rack_num field will not be valid until a future release."
--#TYPE "StorageCell Event"
--#SUMMARY "SCellName-TimeDate %s : SWCID %d : ECode: %d : CAC %d : EIP %d."
--#ARGUMENTS {0,1,2,3,4,}
--#SEVERITY INFORMATIONAL
--#TIMEINDEX 136
--#STATE WARNING
::= 13601592{'RFC-1212': ['OBJECT-TYPE'], 'RFC-1215': ['TRAP-TYPE'], 'RFC1155-SMI': ['enterprises'], 'RFC1213-MIB': ['DisplayString']}Downloaded: 2026-10-23T19:25:41.221277+00:00.
| OID | Name | Direct children | Descendants | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.232.0.136000108 | mngmtAgentTrap_108, mngmtAgentTrap-108 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000109 | mngmtAgentTrap_109, mngmtAgentTrap-109 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000110 | mngmtAgentTrap_110, mngmtAgentTrap-110 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000111 | mngmtAgentTrap_111, mngmtAgentTrap-111 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000112 | mngmtAgentTrap_112, mngmtAgentTrap-112 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000113 | mngmtAgentTrap_113, mngmtAgentTrap-113 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000114 | mngmtAgentTrap_114, mngmtAgentTrap-114 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000115 | mngmtAgentTrap_115, mngmtAgentTrap-115 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000116 | mngmtAgentTrap_116, mngmtAgentTrap-116 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000117 | mngmtAgentTrap_117, mngmtAgentTrap-117 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000118 | mngmtAgentTrap_118, mngmtAgentTrap-118 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000119 | mngmtAgentTrap_119, mngmtAgentTrap-119 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000120 | mngmtAgentTrap_120, mngmtAgentTrap-120 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000121 | mngmtAgentTrap_121, mngmtAgentTrap-121 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000122 | mngmtAgentTrap_122, mngmtAgentTrap-122 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000123 | mngmtAgentTrap_123, mngmtAgentTrap-123 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000124 | mngmtAgentTrap_124, mngmtAgentTrap-124 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000125 | mngmtAgentTrap_125, mngmtAgentTrap-125 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000126 | mngmtAgentTrap_126, mngmtAgentTrap-126 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000127 | mngmtAgentTrap_127, mngmtAgentTrap-127 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000128 | mngmtAgentTrap_128, mngmtAgentTrap-128 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000129 | mngmtAgentTrap_129, mngmtAgentTrap-129 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000130 | mngmtAgentTrap_130, mngmtAgentTrap-130 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000131 | mngmtAgentTrap_131, mngmtAgentTrap-131 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000132 | mngmtAgentTrap_132, mngmtAgentTrap-132 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000133 | mngmtAgentTrap_133, mngmtAgentTrap-133 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000134 | mngmtAgentTrap-134 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000141 | mngmtAgentTrap-141 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000142 | mngmtAgentTrap-142 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000148 | mngmtAgentTrap-148 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000180 | mngmtAgentTrap-180 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000181 | mngmtAgentTrap-181 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000182 | mngmtAgentTrap-182 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000183 | mngmtAgentTrap-183 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000184 | mngmtAgentTrap-184 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000195 | mngmtAgentTrap-195 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000196 | mngmtAgentTrap-196 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000197 | mngmtAgentTrap-197 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000198 | mngmtAgentTrap-198 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000199 | mngmtAgentTrap-199 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000200 | mngmtAgentTrap-200 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000201 | mngmtAgentTrap-201 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000202 | mngmtAgentTrap-202 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000203 | mngmtAgentTrap-203 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000204 | mngmtAgentTrap-204 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000205 | mngmtAgentTrap-205 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000206 | mngmtAgentTrap-206 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000207 | mngmtAgentTrap-207 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000208 | mngmtAgentTrap-208 | 0 | 0 | |
| 1.3.6.1.4.1.232.0.136000209 | mngmtAgentTrap-209 | 0 | 0 |