Status in source: current.
Names: aggregatorL2Collisions
Technical details
{
"smi_kind": "OBJECT-TYPE",
"definition": [
"aggregatorL2Collisions",
"OBJECT-TYPE",
"SYNTAX",
"Counter32",
"MAX-ACCESS",
"read-only",
"STATUS",
"current",
"DESCRIPTION",
"\"The best estimate of the total number of collisions on this Ethernet segment. The value returned will depend on the RMON probe's location. Sections 8.2.1.3 (10BASE-5) and 10.3.1.3 (10BASE-2) of IEEE standard 802.3 states that a station must detect a collision in the receive mode if three or more stations are transmitting simultaneously. A repeater port must detect a collision when two or more stations are transmitting simultaneously. Thus a probe placed on a repeater port could record more collisions than a probe connected to a station on the same segment would. Probe location plays a much smaller role when considering 10BASE-T. Section 14.2.1.4 (10BASE-T) of IEEE standard 802.3 defines a collision as the simultaneous presence of signals on the DO and RD circuits (transmitting and receiving at the same time). A 10BASE-T station can only detect collisions when it is transmitting. Thus probes placed on a station and a repeater, should report the same number of collisions. Note also that an RMON probe inside a repeater should ideally report collisions between the repeater and one or more other hosts (transmit collisions as defined by IEEE 802.3k) plus receiver collisions observed on any coaxial segments to which the repeater is connected.\"",
"::=",
"{",
"portsAggregationEntry",
"17",
"}"
],
"syntax_tree": [
[
"ApplicationSyntax",
"Counter32"
],
null,
[
"MaxAccessPart",
"read-only"
],
[
"Status",
"current"
],
[
"DESCRIPTION",
"The best estimate of the total number of collisions on this Ethernet segment. The value returned will depend on the RMON probe's location. Sections 8.2.1.3 (10BASE-5) and 10.3.1.3 (10BASE-2) of IEEE standard 802.3 states that a station must detect a collision in the receive mode if three or more stations are transmitting simultaneously. A repeater port must detect a collision when two or more stations are transmitting simultaneously. Thus a probe placed on a repeater port could record more collisions than a probe connected to a station on the same segment would. Probe location plays a much smaller role when considering 10BASE-T. Section 14.2.1.4 (10BASE-T) of IEEE standard 802.3 defines a collision as the simultaneous presence of signals on the DO and RD circuits (transmitting and receiving at the same time). A 10BASE-T station can only detect collisions when it is transmitting. Thus probes placed on a station and a repeater, should report the same number of collisions. Note also that an RMON probe inside a repeater should ideally report collisions between the repeater and one or more other hosts (transmit collisions as defined by IEEE 802.3k) plus receiver collisions observed on any coaxial segments to which the repeater is connected."
],
null,
null,
null,
null
]
}
- Multiple manufacturers; see the original MIB MIB copies (LibreNMS/Observium Community)
· Publisher's source file: PRVT-PORTS-AGGREGATION-MIB
Vendor MIB copy from the LibreNMS archive.
Module: PRVT-PORTS-AGGREGATION-MIB
See published definition above
Module imports
{'SNMPv2-TC': ['DisplayString', 'TruthValue'], 'SNMPv2-SMI': ['NOTIFICATION-TYPE', 'MODULE-IDENTITY', 'OBJECT-TYPE', 'Counter32', 'Integer32'], 'RFC1213-MIB': ['ifIndex', 'ifAdminStatus', 'ifOperStatus'], 'Q-BRIDGE-MIB': ['PortList'], 'PRVT-SWITCH-MIB': ['switch', 'configL2IfaceUnit', 'configL2IfaceSlot', 'configL2IfacePort']}
· Download PRVT-PORTS-AGGREGATION-MIB
Related source files and packages: