docsQosParamSetMinReservedRate OBJECT-TYPE
SYNTAX BitRate
MAX-ACCESS read-only
STATUS current
DESCRIPTION "Specifies the guaranteed minimum rate in
bits/sec for this parameter set. The value is
calculated from the byte following the MAC
header HCS to the end of the CRC. The default
value of 0 has the meaning that no bandwidth
is reserved.
If the referenced parameter is not present in the
corresponding DOCSIS QOS Parameter Set, the default
value of this object is 0. If the parameter
is not applicable, it is reported as 0.
"
REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.5.5"
View at oid-info.com
Specifies the guaranteed minimum rate in
bits/sec for this parameter set. The value is
calculated from the byte following the MAC
header HCS to the end of the CRC. The default
value of 0 has the meaning that no bandwidth
is reserved.
If the referenced parameter is not present in the
corresponding DOCSIS QOS Parameter Set, the default
value of this object is 0. If the parameter
is not applicable, it is reported as 0.
Parsed from file DOCS-QOS-MIB-ipcdn-05.txt
Company: None
Module: DOCS-QOS-MIB
Specifies the guaranteed minimum rate in
bits/sec for this parameter set. The value is
calculated from the byte following the MAC
header HCS to the end of the CRC. The default
value of 0 has the meaning that no bandwidth
is reserved.
If the referenced parameter is not present in the
corresponding DOCSIS QOS Parameter Set, the default
value of this object is 0. If the parameter
is not applicable, it is reported as 0.
Parsed from file DOCS-QOS-MIB.mib
Module: DOCS-QOS-MIB
Automatically extracted from Cisco "SNMP v2 MIBs".
docsQosParamSetMinReservedRate OBJECT-TYPE SYNTAX BitRate MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the guaranteed minimum rate in bits/sec for this parameter set. The value is calculated from the byte following the MAC header HCS to the end of the CRC. The default value of 0 has the meaning that no bandwidth is reserved. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, the default value of this object is 0. If the parameter is not applicable, it is reported as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.5.5" ::= { docsQosParamSetEntry 8 }
docsQosParamSetMinReservedRate OBJECT-TYPE SYNTAX BitRate MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the guaranteed minimum rate in bits/sec for this parameter set. The value is calculated from the byte following the MAC header HCS to the end of the CRC. The default value of 0 has the meaning that no bandwidth is reserved. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, the default value of this object is 0. If the parameter is not applicable, it is reported as 0. " REFERENCE "SP-RFIv1.1-I05-000714, Appendix C.2.2.5.5" ::= { docsQosParamSetEntry 8 }
Internet Assigned Numbers Authority
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.10.127.7.1.2.2.4 | docsQosParamSetServiceClassName | 0 | 0 | Refers to the Service Class Name that the parameter set values were derived. If the referenced parameter is not present in the cor… |
| 1.3.6.1.2.1.10.127.7.1.2.2.5 | docsQosParamSetPriority | 0 | 0 | The relative priority of a service flow. Higher numbers indicate higher priority. This priority should only be used to differenti… |
| 1.3.6.1.2.1.10.127.7.1.2.2.6 | docsQosParamSetMaxTrafficRate | 0 | 0 | Maximum sustained traffic rate allowed for this service flow in bits/sec. Must count all MAC frame data PDU from the bytes follow… |
| 1.3.6.1.2.1.10.127.7.1.2.2.7 | docsQosParamSetMaxTrafficBurst | 0 | 0 | Specifies the token bucket size in bytes for this parameter set. The value is calculated from the byte following the MAC header H… |
| 1.3.6.1.2.1.10.127.7.1.2.2.9 | docsQosParamSetMinReservedPkt | 0 | 0 | Specifies an assumed minimum packet size in bytes for which the docsQosParamSetMinReservedRate will be provided. The value is cal… |
| 1.3.6.1.2.1.10.127.7.1.2.2.10 | docsQosParamSetActiveTimeout | 0 | 0 | Specifies the maximum duration in seconds that resources remain unused on an active service flow before CMTS signals that both ac… |
| 1.3.6.1.2.1.10.127.7.1.2.2.11 | docsQosParamSetAdmittedTimeout | 0 | 0 | Specifies the maximum duration in seconds that resources remain in admitted state before resources must be released. The value of … |
| 1.3.6.1.2.1.10.127.7.1.2.2.12 | docsQosParamSetMaxConcatBurst | 0 | 0 | Specifies the maximum concatenated burst in bytes which an upstream service flow is allowed. The value is calculated from the FC… |
| 1.3.6.1.2.1.10.127.7.1.2.2.13 | docsQosParamSetSchedulingType | 0 | 0 | Specifies the upstream scheduling service used for upstream service flow. If the referenced parameter is not present in the corres… |
| 1.3.6.1.2.1.10.127.7.1.2.2.15 | docsQosParamSetNomPollInterval | 0 | 0 | Specifies the nominal interval in microseconds between successive unicast request opportunities on an upstream service flow. This … |
| 1.3.6.1.2.1.10.127.7.1.2.2.16 | docsQosParamSetTolPollJitter | 0 | 0 | Specifies the maximum amount of time in microseconds that the unicast request interval may be delayed from the nominal periodic sc… |
| 1.3.6.1.2.1.10.127.7.1.2.2.17 | docsQosParamSetUnsolicitGrantSize | 0 | 0 | Specifies the unsolicited grant size in bytes. The grant size includes the entired MAC frame data PDU from the Frame Control byte… |
| 1.3.6.1.2.1.10.127.7.1.2.2.18 | docsQosParamSetNomGrantInterval | 0 | 0 | Specifies the nominal interval in microseconds between successive data grant opportunities on an upstream service flow. The refere… |
| 1.3.6.1.2.1.10.127.7.1.2.2.19 | docsQosParamSetTolGrantJitter | 0 | 0 | Specifies the maximum amount of time in microseconds that the transmission opportunities may be delayed from the nominal periodic… |
| 1.3.6.1.2.1.10.127.7.1.2.2.20 | docsQosParamSetGrantsPerInterval | 0 | 0 | Specifies the number of data grants per Nominal Grant Interval (docsQosParamSetNomGrantInterval). The referenced parameter is appl… |
| 1.3.6.1.2.1.10.127.7.1.2.2.21 | docsQosParamSetTosAndMask | 0 | 0 | docsQosParamSetTosAndMask OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1)) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies … |
| 1.3.6.1.2.1.10.127.7.1.2.2.22 | docsQosParamSetTosOrMask | 0 | 0 | Specifies the OR mask for IP TOS byte. See the description of docsQosParamSetTosAndMask for further details. |
| 1.3.6.1.2.1.10.127.7.1.2.2.23 | docsQosParamSetMaxLatency | 0 | 0 | Specifies the maximum latency between the reception of a packet by the CMTS on its NSI and the forwarding of the packet to the RF… |
| 1.3.6.1.2.1.10.127.7.1.2.2.24 | docsQosParamSetType | 0 | 0 | Defines the type of the QOS parameter set defined by this row. active(1) indicates the Active QOS parameter set, describing the s… |
| 1.3.6.1.2.1.10.127.7.1.2.2.25 | docsQosParamSetRequestPolicyOct | 0 | 0 | Specifies which transmit interval opportunities the CM omits for upstream transmission requests and packet transmissions. This ob… |
| 1.3.6.1.2.1.10.127.7.1.2.2.26 | docsQosParamSetBitMap | 0 | 0 | This object indicates the set of QOS Parameter Set parameters actually signaled in the DOCSIS registration or dynamic service req… |