lmpModuleFullCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance statement for agents that support the
configuration and monitoring of LMP MIB."
MODULE -- this module
MANDATORY-GROUPS { lmpNodeGroup,
lmpControlChannelGroup,
lmpLinkPropertyCorrelationGroup,
lmpPerfGroup,
lmpTeLinkGroup,
lmpDataLinkGroup }
GROUP lmpCcIsNotInterfaceGroup
DESCRIPTION
"This group is mandatory for devices that support
control channels that are not interfaces, in addition to
lmpControlChannelGroup. The following constraints apply:
lmpCcIsIf must at least be read-only returning false(1)."
GROUP lmpCcIsInterfaceGroup
DESCRIPTION
"This group is mandatory for devices that support
control channels that are interfaces, in addition to
lmpControlChannelGroup. The following constraints apply:
lmpCcIsIf must at least be read-only returning true(2)."
GROUP lmpLinkVerificationGroup
DESCRIPTION
"This group is mandatory for devices that support
the link verification procedure."
GROUP lmpNotificationGroup
DESCRIPTION
"This group is optional."
-- lmpNbrTable
OBJECT lmpNbrRowStatus
SYNTAX RowStatus { active(1), notInService(2) }
WRITE-SYNTAX RowStatus { active(1), notInService(2),
createAndGo(4), destroy(6) }
DESCRIPTION
"Support for notReady(3) and createAndWait(5) is
not required."
-- lmpControlChannelTable
OBJECT lmpCcRemoteAddressType
SYNTAX INTEGER { unknown(0), ipv4(1), ipv6(2) }
DESCRIPTION
"Only ipv4(1) and ipv6(2) address types need to be
supported for non-point-to-point configurations."
OBJECT lmpCcRemoteIpAddr
SYNTAX InetAddress (SIZE(0|4|16))
DESCRIPTION
"The size of the IP address depends on the address type."
OBJECT lmpCcRowStatus
SYNTAX RowStatus { active(1), notInService(2) }
WRITE-SYNTAX RowStatus { active(1), notInService(2),
createAndGo(4), destroy(6) }
DESCRIPTION
"Support for notReady(3) and createAndWait(5) is
not required."
OBJECT lmpCcOperStatus
SYNTAX INTEGER { up(1), down(2) }
DESCRIPTION
"A value of configSnd(3), configRcv(4), active(5),
goingDown(6) need not be supported."
-- lmpTeLinkTable
OBJECT lmpTeLinkOperStatus
SYNTAX INTEGER { up(1), down(2), degraded(5) }
DESCRIPTION
"The testing(3) and init(4) state need not be supported."
OBJECT lmpTeLinkRowStatus
SYNTAX RowStatus { active(1), notInService(2) }
WRITE-SYNTAX RowStatus { active(1), notInService(2),
createAndGo(4), destroy(6) }
DESCRIPTION
"Support for notReady(3) and createAndWait(5) is
not required."
-- lmpDataLinkTable
OBJECT lmpDataLinkActiveOperStatus
SYNTAX INTEGER { upAlloc(1), upFree(2), down(3) }
DESCRIPTION
"A value of testing(4) need not be supported."
OBJECT lmpDataLinkPassiveOperStatus
SYNTAX INTEGER { upAlloc(1), upFree(2), down(3) }
DESCRIPTION
"A value of psvTst(4) need not be supported."
OBJECT lmpDataLinkRowStatus
SYNTAX RowStatus { active(1), notInService(2) }
WRITE-SYNTAX RowStatus { active(1), notInService(2),
createAndGo(4), destroy(6) }
DESCRIPTION
"Support for notReady(3) and createAndWait(5) is
not required."
View at oid-info.com
Compliance statement for agents that support the
LMP MIB.
Parsed from file rfc4631-Link-Management-Protocol-LMP.mib.txt
Company: None
Module: LMP-MIB
Compliance statement for agents that support the
configuration and monitoring of LMP MIB.
Parsed from file LMP-MIB.mib
Module: LMP-MIB
Automatically extracted from RFC4327
lmpModuleCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Compliance statement for agents that support the LMP MIB." MODULE MANDATORY-GROUPS { lmpNodeGroup, lmpControlChannelGroup, lmpLinkPropertyCorrelationGroup, lmpPerfGroup, lmpTeLinkGroup, lmpDataBearingLinkGroup } GROUP lmpControlChannelIsNotInterfaceGroup DESCRIPTION "This group is mandatory for devices which support control channels that are not interfaces, in addition to lmpControlChannelGroup. The following constraints apply: lmpCcIsIf must at least be read-only returning false(1)." GROUP lmpControlChannelIsInterfaceGroup DESCRIPTION "This group is mandatory for devices which support control channels that are interfaces, in addition to lmpControlChannelGroup. The following constraints apply: lmpCcIsIf must at least be read-only returning true(2)." GROUP lmpLinkVerificationGroup DESCRIPTION "This group is mandatory for devices which support the link verification procedure." OBJECT lmpAdminStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpLinkVerificationInterval MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpCcHelloIntervalDefault MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpCcHelloIntervalDefaultMin MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpCcHelloIntervalDefaultMax MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpCcHelloDeadIntervalDefault MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpCcHelloDeadIntervalDefaultMin MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpCcHelloDeadIntervalDefaultMax MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpNbrRetransmitInterval MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpNbrRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } MIN-ACCESS read-only DESCRIPTION "The notReady(3) and createAndWait(5) states need not be supported." OBJECT lmpNbrStorageType SYNTAX INTEGER { other(1) } MIN-ACCESS read-only DESCRIPTION "Only other(1) needs to be supported." OBJECT lmpCcUnderlyingIfIndex MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpCcIsIf MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpCcSetupRole MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpCcAuthentication MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpCcConfigRetransmitInterval MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpCcConfigRetransmitTimeout MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpCcHelloIntervalMin MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpCcHelloIntervalMax MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpCcHelloDeadIntervalMin MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpCcHelloDeadIntervalMax MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpCcRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } MIN-ACCESS read-only DESCRIPTION "The notReady(3) and createAndWait(5) states need not be supported." OBJECT lmpCcOperStatus SYNTAX INTEGER { up(1), down(2) } MIN-ACCESS read-only DESCRIPTION "A value of active(3), configuring(4), goingDown(5) need not be supported." OBJECT lmpCcStorageType SYNTAX INTEGER { other(1) } MIN-ACCESS read-only DESCRIPTION "Only other(1) needs to be supported." OBJECT lmpVerifyInterval MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpVerifyDeadInterval MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpVerifyAllLinks MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpTeLinkNbrNodeId MIN-ACCESS read-only DESCRIPTION "Write access is not required if the link verification procedure is enabled." OBJECT lmpTeLinkVerification MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpTeLinkFaultIsolation MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpTeLinkDwdm MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpTeLinkOperStatus SYNTAX INTEGER { up(1), down(2), degraded(4) } MIN-ACCESS read-only DESCRIPTION "The testing(3) state need not be supported." OBJECT lmpTeLinkRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } MIN-ACCESS read-only DESCRIPTION "The notReady(3) and createAndWait(5) states need not be supported." OBJECT lmpTeLinkStorageType SYNTAX INTEGER { other(1) } MIN-ACCESS read-only DESCRIPTION "Only other(1) needs to be supported." OBJECT lmpTeLinkBitRate MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpTeLinkWavelength MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpDataBearingLinkRemoteIfId MIN-ACCESS read-only DESCRIPTION "Write access is not required if the link verification procedure is enabled." OBJECT lmpDataBearingLinkEncodingType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT lmpDataBearingLinkOperStatus SYNTAX INTEGER { up(1), down(2), degraded(4) } MIN-ACCESS read-only DESCRIPTION "A value of testing(3) need not be supported." OBJECT lmpDataBearingLinkRowStatus SYNTAX INTEGER { active(1), notInService(2), createAndGo(4), destroy(6) } MIN-ACCESS read-only DESCRIPTION "The notReady(3) and createAndWait(5) states need not be supported." OBJECT lmpDataBearingLinkStorageType SYNTAX INTEGER { other(1) } MIN-ACCESS read-only DESCRIPTION "Only other(1) needs to be supported." ::= { lmpCompliances 1 }
lmpModuleFullCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Compliance statement for agents that support the configuration and monitoring of LMP MIB." MODULE MANDATORY-GROUPS { lmpNodeGroup, lmpControlChannelGroup, lmpLinkPropertyCorrelationGroup, lmpPerfGroup, lmpTeLinkGroup, lmpDataLinkGroup } GROUP lmpCcIsNotInterfaceGroup DESCRIPTION "This group is mandatory for devices that support control channels that are not interfaces, in addition to lmpControlChannelGroup. The following constraint applies: lmpCcIsIf must at least be read-only, returning false(2)." GROUP lmpCcIsInterfaceGroup DESCRIPTION "This group is mandatory for devices that support control channels that are interfaces, in addition to lmpControlChannelGroup. The following constraint applies: lmpCcIsIf must at least be read-only, returning true(1)." GROUP lmpLinkVerificationGroup DESCRIPTION "This group is mandatory for devices that support the link verification procedure." GROUP lmpNotificationGroup DESCRIPTION "This group is optional." OBJECT lmpNbrRowStatus SYNTAX RowStatus { active(1), notInService(2) } WRITE-SYNTAX RowStatus { active(1), notInService(2), createAndGo(4), destroy(6) } DESCRIPTION "Support for notReady(3) and createAndWait(5) is not required." OBJECT lmpCcRemoteAddressType SYNTAX INTEGER { unknown(0), ipv4(1), ipv6(2) } DESCRIPTION "Only ipv4(1) and ipv6(2) address types need to be supported for non-point-to-point configurations." OBJECT lmpCcRemoteIpAddr SYNTAX InetAddress (SIZE(0|4|16)) DESCRIPTION "The size of the IP address depends on the address type." OBJECT lmpCcRowStatus SYNTAX RowStatus { active(1), notInService(2) } WRITE-SYNTAX RowStatus { active(1), notInService(2), createAndGo(4), destroy(6) } DESCRIPTION "Support for notReady(3) and createAndWait(5) is not required." OBJECT lmpCcOperStatus SYNTAX INTEGER { up(1), down(2) } DESCRIPTION "A value of configSnd(3), configRcv(4), active(5), or goingDown(6) need not be supported." OBJECT lmpTeLinkOperStatus SYNTAX INTEGER { up(1), down(2), degraded(5) } DESCRIPTION "The testing(3) and init(4) state need not be supported." OBJECT lmpTeLinkRowStatus SYNTAX RowStatus { active(1), notInService(2) } WRITE-SYNTAX RowStatus { active(1), notInService(2), createAndGo(4), destroy(6) } DESCRIPTION "Support for notReady(3) and createAndWait(5) is not required." OBJECT lmpDataLinkActiveOperStatus SYNTAX INTEGER { upAlloc(1), upFree(2), down(3) } DESCRIPTION "A value of testing(4) need not be supported." OBJECT lmpDataLinkPassiveOperStatus SYNTAX INTEGER { upAlloc(1), upFree(2), down(3) } DESCRIPTION "A value of psvTst(4) need not be supported." OBJECT lmpDataLinkRowStatus SYNTAX RowStatus { active(1), notInService(2) } WRITE-SYNTAX RowStatus { active(1), notInService(2), createAndGo(4), destroy(6) } DESCRIPTION "Support for notReady(3) and createAndWait(5) is not required." ::= { lmpCompliances 1 }
Internet Assigned Numbers Authority
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.10.227.2.1.2 | lmpModuleReadOnlyCompliance | 0 | 0 | Compliance statement for agents that support the monitoring of the LMP MIB. |