Indicates current state of the ATUC line. This is a
bit-map of possible conditions. The various bit
positions are:
0 noDefect There no defects on the line
1 lossOfFraming ATUC failure due to not
receiving valid frame.
2 lossOfSignal ATUC failure due to not
receiving signal.
3 lossOfPower ATUC failure due to loss of
power.
Note: the Agent may still
function.
4 lossOfSignalQuality Loss of Signal Quality is
declared when the Noise Margin
falls below the Minimum Noise
Margin, or the bit-error-rate
exceeds 10^-7.
5 lossOfLink ATUC failure due to inability
to link with ATUR.
6 dataInitFailure ATUC failure during
initialization due to bit
errors corrupting startup
exchange data.
7 configInitFailure ATUC failure during
initialization due to peer
ATU not able to support
requested configuration
8 protocolInitFailure ATUC failure during
initialization due to
incompatible protocol used by
the peer ATU.
9 noPeerAtuPresent ATUC failure during
initialization due to no
activation sequence detected
from peer ATU.
This is intended to supplement ifOperStatus.
Parsed from file ADSL-LINE-MIB.mib
Module: ADSL-LINE-MIB
Indicates current state of the ATUC line. This is a
bit-map of possible conditions. The various bit
positions are:
0 noDefect There no defects on the line
1 lossOfFraming ATUC failure due to not
receiving valid frame.
2 lossOfSignal ATUC failure due to not
receiving signal.
3 lossOfPower ATUC failure due to loss of
power.
Note: the Agent may still
function.
4 lossOfSignalQuality Loss of Signal Quality is
declared when the Noise Margin
falls below the Minimum Noise
Margin, or the bit-error-rate
exceeds 10^-7.
5 lossOfLink ATUC failure due to inability
to link with ATUR.
6 dataInitFailure ATUC failure during
initialization due to bit
errors corrupting startup
exchange data.
7 configInitFailure ATUC failure during
initialization due to peer
ATU not able to support
requested configuration
8 protocolInitFailure ATUC failure during
initialization due to
incompatible protocol used by
the peer ATU.
9 noPeerAtuPresent ATUC failure during
initialization due to no
activation sequence detected
from peer ATU.
This is intended to supplement ifOperStatus.
SYNTAX BITS {
noDefect(0),
lossOfFraming(1),
lossOfSignal(2),
lossOfPower(3),
lossOfSignalQuality(4),
lossOfLink(5),
dataInitFailure(6),
configInitFailure(7),
protocolInitFailure(8),
noPeerAtuPresent(9)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates current state of the ATUC line. This is a
bit-map of possible conditions. The various bit
positions are:
0 noDefect There no defects on the line
1 lossOfFraming ATUC failure due to not
receiving valid frame.
2 lossOfSignal ATUC failure due to not
receiving signal.
3 lossOfPower ATUC failure due to loss of
power.
Note: the Agent may still
function.
4 lossOfSignalQuality Loss of Signal Quality is
declared when the Noise Margin
falls below the Minimum Noise
Margin, or the bit-error-rate
exceeds 10^-7.
5 lossOfLink ATUC failure due to inability
to link with ATUR.
6 dataInitFailure ATUC failure during
initialization due to bit
errors corrupting startup
exchange data.
7 configInitFailure ATUC failure during
initialization due to peer
ATU not able to support
requested configuration
8 protocolInitFailure ATUC failure during
initialization due to
incompatible protocol used by
the peer ATU.
9 noPeerAtuPresent ATUC failure during
initialization due to no
activation sequence detected
from peer ATU.
This is intended to supplement ifOperStatus."
View at oid-info.com
Indicates current state of the ATUC line. This is a
bit-map of possible conditions. The various bit
positions are:
0 noDefect There no defects on the line
1 lossOfFraming ATUC failure due to not
receiving valid frame.
2 lossOfSignal ATUC failure due to not
receiving signal.
3 lossOfPower ATUC failure due to loss of
power.
Note: the Agent may still
function.
4 lossOfSignalQuality Loss of Signal Quality is
declared when the Noise Margin
falls below the Minimum Noise
Margin, or the bit-error-rate
exceeds 10^-7.
5 lossOfLink ATUC failure due to inability
to link with ATUR.
6 dataInitFailure ATUC failure during
initialization due to bit
errors corrupting startup
exchange data.
7 configInitFailure ATUC failure during
initialization due to peer
ATU not able to support
requested configuration
8 protocolInitFailure ATUC failure during
initialization due to
incompatible protocol used by
the peer ATU.
9 noPeerAtuPresent ATUC failure during
initialization due to no
activation sequence detected
from peer ATU.
This is intended to supplement ifOperStatus.
Parsed from file adsl-line.mib.txt
Company: None
Module: ADSL-LINE-MIB
Indicates current state of the ATUC line. This is a
bit-map of possible conditions. The various bit
positions are:
0 noDefect There no defects on the line
1 lossOfFraming ATUC failure due to not
receiving valid frame.
2 lossOfSignal ATUC failure due to not
receiving signal.
3 lossOfPower ATUC failure due to loss of
power.
Note: the Agent may still
function.
4 lossOfSignalQuality Loss of Signal Quality is
declared when the Noise Margin
falls below the Minimum Noise
Margin, or the bit-error-rate
exceeds 10^-7.
5 lossOfLink ATUC failure due to inability
to link with ATUR.
6 dataInitFailure ATUC failure during
initialization due to bit
errors corrupting startup
exchange data.
7 configInitFailure ATUC failure during
initialization due to peer
ATU not able to support
requested configuration
8 protocolInitFailure ATUC failure during
initialization due to
incompatible protocol used by
the peer ATU.
9 noPeerAtuPresent ATUC failure during
initialization due to no
activation sequence detected
from peer ATU.
This is intended to supplement ifOperStatus.
adslAtucCurrStatus OBJECT-TYPE SYNTAX BITS { noDefect(0), lossOfFraming(1), lossOfSignal(2), lossOfPower(3), lossOfSignalQuality(4), lossOfLink(5), dataInitFailure(6), configInitFailure(7), protocolInitFailure(8), noPeerAtuPresent(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates current state of the ATUC line. This is a bit-map of possible conditions. The various bit positions are: 0 noDefect There no defects on the line 1 lossOfFraming ATUC failure due to not receiving valid frame. 2 lossOfSignal ATUC failure due to not receiving signal. 3 lossOfPower ATUC failure due to loss of power. Note: the Agent may still function. 4 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. 5 lossOfLink ATUC failure due to inability to link with ATUR. 6 dataInitFailure ATUC failure during initialization due to bit errors corrupting startup exchange data. 7 configInitFailure ATUC failure during initialization due to peer ATU not able to support requested configuration 8 protocolInitFailure ATUC failure during initialization due to incompatible protocol used by the peer ATU. 9 noPeerAtuPresent ATUC failure during initialization due to no activation sequence detected from peer ATU. This is intended to supplement ifOperStatus." ::= { adslAtucPhysEntry 6 }
adslAtucCurrStatus OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "Indicates current state of the ATUC line. This is a bit-map of possible conditions. The various bit positions are: 0 noDefect There no defects on the line 1 lossOfFraming ATUC failure due to not receiving valid frame. 2 lossOfSignal ATUC failure due to not receiving signal. 3 lossOfPower ATUC failure due to loss of power. Note: the Agent may still function. 4 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. 5 lossOfLink ATUC failure due to inability to link with ATUR. 6 dataInitFailure ATUC failure during initialization due to bit errors corrupting startup exchange data. 7 configInitFailure ATUC failure during initialization due to peer ATU not able to support requested configuration 8 protocolInitFailure ATUC failure during initialization due to incompatible protocol used by the peer ATU. 9 noPeerAtuPresent ATUC failure during initialization due to no activation sequence detected from peer ATU. This is intended to supplement ifOperStatus." ::= { adslAtucPhysEntry 6 }
Defined in RFC2662
adslAtucCurrStatus OBJECT-TYPE SYNTAX BITS { noDefect(0), lossOfFraming(1), lossOfSignal(2), lossOfPower(3), lossOfSignalQuality(4), lossOfLink(5), dataInitFailure(6), configInitFailure(7), protocolInitFailure(8), noPeerAtuPresent(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates current state of the ATUC line. This is a bit-map of possible conditions. The various bit positions are: 0 noDefect There no defects on the line 1 lossOfFraming ATUC failure due to not receiving valid frame. 2 lossOfSignal ATUC failure due to not receiving signal. 3 lossOfPower ATUC failure due to loss of power. Note: the Agent may still function. 4 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. 5 lossOfLink ATUC failure due to inability to link with ATUR. 6 dataInitFailure ATUC failure during initialization due to bit errors corrupting startup exchange data. 7 configInitFailure ATUC failure during initialization due to peer ATU not able to support requested configuration 8 protocolInitFailure ATUC failure during initialization due to incompatible protocol used by the peer ATU. 9 noPeerAtuPresent ATUC failure during initialization due to no activation sequence detected from peer ATU. This is intended to supplement ifOperStatus." ::= { adslAtucPhysEntry 6 }
adslAtucCurrStatus OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates current state of the ATUC line. This is a bit-map of possible conditions. The various bit positions are: 0 noDefect There no defects on the line 1 lossOfFraming ATUC failure due to not receiving valid frame. 2 lossOfSignal ATUC failure due to not receiving signal. 3 lossOfPower ATUC failure due to loss of power. Note: the Agent may still function. 4 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. 5 lossOfLink ATUC failure due to inability to link with ATUR. 6 dataInitFailure ATUC failure during initialization due to bit errors corrupting startup exchange data. 7 configInitFailure ATUC failure during initialization due to peer ATU not able to support requested configuration 8 protocolInitFailure ATUC failure during initialization due to incompatible protocol used by the peer ATU. 9 noPeerAtuPresent ATUC failure during initialization due to no activation sequence detected from peer ATU. This is intended to supplement ifOperStatus." ::= { adslAtucPhysEntry 6 }
Internet Assigned Numbers Authority
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.10.94.1.1.2.1.1 | adslAtucInvSerialNumber | 0 | 0 | Vendor specific string that identifies the vendor equipment. |
| 1.3.6.1.2.1.10.94.1.1.2.1.2 | adslAtucInvVendorID | 0 | 0 | The vendor ID assigned by T1E1.413 according to its Annex D.[10] |
| 1.3.6.1.2.1.10.94.1.1.2.1.3 | adslAtucInvVersionNumber | 0 | 0 | Vendor specific version number sent by this ATU as part of the initialization messages. |
| 1.3.6.1.2.1.10.94.1.1.2.1.4 | adslAtucCurrSnrMgn | 0 | 0 | Noise Margin as seen by this ATU with respect to its received signal in tenth dB. |
| 1.3.6.1.2.1.10.94.1.1.2.1.5 | adslAtucCurrAtn | 0 | 0 | Measured difference in the total power transmitted by the peer ATU and the total power received by this ATU. |
| 1.3.6.1.2.1.10.94.1.1.2.1.7 | adslAtucCurrOutputPwr | 0 | 0 | Measured total output power transmitted by this ATU. This is the measurement that was reported during the last activation sequenc… |
| 1.3.6.1.2.1.10.94.1.1.2.1.8 | adslAtucCurrAttainableRate | 0 | 0 | Indicates the maximum currently attainable data rate by the ATU. This value will be equal or greater than the current line rate. |