Indicates a count of the total pages scanned through the ADF on the
device. This may include scan to host jobs, copyjobs, and fax jobs. If
only the total pages scanned to the host are wanted, use
SCAN-ADF-PAGE-COUNT.
Parsed from file lj3200_snmp.mib.txt
Company: hp
Module: LJ3200-MIB
Child arc 0 is used to translate between SNMPv1 and SNMPv2 notification parameters as explained in IETF RFC 2576, section 3.
scanner-adf-page-count OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS optional DESCRIPTION "Indicates a count of the total pages scanned through the ADF on the device. This may include scan to host jobs, copyjobs, and fax jobs. If only the total pages scanned to the host are wanted, use SCAN-ADF-PAGE-COUNT." ::= { settings-scanner 44 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.44.0 | scanner-adf-page-count | 0 | 0 | None |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.1 | scan-contrast | 1 | 1 | Behaves as SCL's 'Set Scanner Contrast Level' command which is used for setting the scanner contrast level. Range is 0..100. Addit… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.2 | scan-resolution | 1 | 1 | struct { unsigned_32bit x_res; /* 1st four bytes; big endian */ unsigned_32bit y_res; /* 2nd four bytes; big endian */ } Sets the s… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.3 | scan-pixel-data-type | 1 | 1 | Sets the method used when scanning. eBiLevelThesholded - One bit per pixel, using simple thresholding of greyscale scan data. eBiL… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.4 | scan-compression | 1 | 1 | Indicates the type of data compression applied to the image data in the scanning upload session. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.5 | scan-compression-factor | 1 | 1 | Indicates the level of compression to be applied to the scanned image data for upload. Range is normalized to be between 0..100.… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.6 | scan-upload-error | 1 | 1 | Error status of the image scanning upload session. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.12 | scan-upload | 1 | 1 | Handshake mechanism between host and device to initiate scan operation and coordinate the transfer of scanned image data to the h… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.16 | default-scanner-margin-left | 1 | 1 | Sets the left scanner margin. The unit of measure should be documented in the device POS. Additional information: The margin value… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.17 | default-scanner-margin-right | 1 | 1 | Sets the right scanner margin. The unit of measure should be documented in the device POS. Additional information: The margin valu… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.18 | scanner-accessory-serial-number | 1 | 1 | Identifies the serial number for the scanner accessory. If this is a writable object, the POS should indicate the maximum support… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.19 | scanner-accessory-model-number | 1 | 1 | Model number of the scanner accessory. This string should only use characters from the US-ASCII code set. Additional information… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.20 | scanner-accessory-adf-sheet-count | 1 | 1 | Total number of sheets that have been fed through the Automatic Document Feed (ADF) accessory. Additional information: The Automat… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.21 | scanner-accessory-flatbed-scan-count | 1 | 1 | Total number of scans performed by a flatbed scanner accessory. Additional information: The count is only incremented when a sheet… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.22 | scanner-accessory-cleaning-interval | 1 | 1 | Recommended cleaning interval in units of sheets scanned. Additional information: Recommended cleaning interval is in units of she… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.23 | scanner-accessory-cleaning-count | 1 | 1 | The number of sheets scanned since the last cleaning was performed. Additional information: The number of sheets that have gone th… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.24 | scanner-accessory-maintenance-interval | 1 | 1 | Recommended maintenance interval in units of sheets scanned. Additional information: Recommended maintenance interval is in units … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.25 | scanner-accessory-maintenance-count | 1 | 1 | The number of sheets scanned since the last maintenance was performed. Additional information: The number of sheets that have gone… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.26 | scanner-accessory-rom-revision | 1 | 1 | ROM revision of the scanner accessory firmware. Additional information: ROM revision of the Fujitsu scanner is downloaded from the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.27 | scanner-accessory-copy-processor-boot-revision | 1 | 1 | Boot ROM revision of scanner copy processor firmware. Boot code to initialize the copy processor, establish communications with t… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.28 | scanner-accessory-copy-processor-runtime-revision | 1 | 1 | Revision of the runtime firmware for the scanner copy processor. Runtime code which retrieves scanned data from the scanner and … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.29 | scanner-accessory-service-agent-revision | 1 | 1 | Revision of scanner service agent firmware. Service agent which accepts scanned data and processes scanner copy processor reques… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.30 | scanner-accessory-control-panel-user-interface-revision | 1 | 1 | Revision of the control panel user interface firmware. Additional information: Revision of the copy processor user interface firmw… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.32 | scan-calibration | 1 | 2 | None |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.33 | scanner-accessory-nvram | 1 | 1 | Returns the contents of the NVRAM (Non-Volatile RAM) located in the scanner accessory. Additional information: Read bytes 0..39 of… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.34 | scanner-accessory-nvram2 | 1 | 1 | Returns the second part of the contents of the NVRAM (Non-Volatile RAM) located in the scanner accessory. Additional information:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.35 | scanner-accessory-nvram3 | 1 | 1 | Returns the third part of the contents of the NVRAM (Non-Volatile RAM) located in the scanner accessory. Additional information: R… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.36 | scanner-accessory-nvram4 | 1 | 1 | Returns the fourth part of the contents of the NVRAM (Non-Volatile RAM) located in the scanner accessory. Additional information:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.37 | ui-add-option | 1 | 1 | Lets the host application set up target (eg.scan) destinations. The destinations can be a host network address and/or an applicat… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.38 | ui-select-option | 1 | 1 | Triggers a job from the device based on the option selected. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.42 | ui-delete-option | 1 | 1 | Lets the host application delete target eg. scan destinations that were setup with UI-ADD-OPTION. The host sends down the entire … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.43 | scanner-jam-page-count | 1 | 1 | Indicates a count of the total pages jammed in the scanner'slifetime. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.45 | scan-adf-page-count | 1 | 1 | Indicates the total pages scanned through the ADF to the host from the device. If the total pages scanned through the scanner ar… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.46 | scan-image-type | 1 | 1 | Indicates the image type of the scan data. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.47 | scan-subsample | 1 | 1 | Indicates the subsampling used for Scan Data. 4:1:1, 4:2:2, and 4:3:3 subsampling are used to modify the scan image quality and … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.48 | scanner-retrieve-scanline | 1 | 1 | This object facilitates the sending of a scan line of data from the scanner to a host. It grabs either raw or corrected data. SE… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.49 | scanner-motor-control | 1 | 1 | This objects is set to the number of steps that the scan motor should move. SERVICE-PASSWORD must be setcorrectly to use this ob… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.50 | scan-height | 1 | 1 | Used to set the height of a scan image in Decapoints. The use of Decapoints as units of measure eliminates the need for the use… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.51 | scanner-scanline-statistics | 1 | 1 | This object is used to obtain statistics about the scan line that was previously obtained using the SCANNER-RETRIEVE-SCANLINE obj… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.52 | scan-control-descriptor | 1 | 1 | Describes the control language and formats supported for this scanner. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.53 | scan-gamma-correction | 1 | 1 | A 32-bit quantity that indicates the gamma correction to use on the scan image. The first 16 bits indicate the integral portion o… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.54 | scan-pad-image | 1 | 1 | Indicates if the scan image should be padded with white data or not. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.63 | scanner-accessory-total-copy-pages-printed | 1 | 1 | This relates to the number of copy pages printed on a device. The output sheet that is duplexed (made 2-sided) should be counted… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.73 | scan-flatbed-page-count | 1 | 1 | This object tracks the page count for the pages scanned from the flatbed. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.74 | scanner-flatbed-page-count | 1 | 1 | This object tracks the page count for the pages scanned for all jobs from the flatbed. This includes scan to host jobs, fax jobs… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.75 | scanner-modular-hardware | 1 | 1 | Used to specify whether optional hardware is installed or not Additional information: HP LaserJet 3300 Series uses this object to … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.76 | default-scanner-margin-top | 1 | 1 | Sets the top scanner margin. The unit of measure should be documented in the device POS. Additional information: This object is a… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.77 | scan-max-line-width | 1 | 1 | Returns the maximum scan line width in pixels for the currently selected resolution. Additional information: Returns the maximum s… |