Describes the control language and formats supported for this scanner.
Parsed from file lj3200_snmp.mib.txt
Company: hp
Module: LJ3200-MIB
Child arc 0 is used to translate between SNMPv1 and SNMPv2 notification parameters as explained in IETF RFC 2576, section 3.
scan-control-descriptor OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS optional DESCRIPTION "Describes the control language and formats supported for this scanner." ::= { settings-scanner 52 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.52.0 | scan-control-descriptor | 0 | 0 | None |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.1 | scan-contrast | 1 | 1 | Behaves as SCL's 'Set Scanner Contrast Level' command which is used for setting the scanner contrast level. Range is 0..100. Addit… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.2 | scan-resolution | 1 | 1 | struct { unsigned_32bit x_res; /* 1st four bytes; big endian */ unsigned_32bit y_res; /* 2nd four bytes; big endian */ } Sets the s… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.3 | scan-pixel-data-type | 1 | 1 | Sets the method used when scanning. eBiLevelThesholded - One bit per pixel, using simple thresholding of greyscale scan data. eBiL… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.4 | scan-compression | 1 | 1 | Indicates the type of data compression applied to the image data in the scanning upload session. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.5 | scan-compression-factor | 1 | 1 | Indicates the level of compression to be applied to the scanned image data for upload. Range is normalized to be between 0..100.… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.6 | scan-upload-error | 1 | 1 | Error status of the image scanning upload session. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.12 | scan-upload | 1 | 1 | Handshake mechanism between host and device to initiate scan operation and coordinate the transfer of scanned image data to the h… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.16 | default-scanner-margin-left | 1 | 1 | Sets the left scanner margin. The unit of measure should be documented in the device POS. Additional information: The margin value… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.17 | default-scanner-margin-right | 1 | 1 | Sets the right scanner margin. The unit of measure should be documented in the device POS. Additional information: The margin valu… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.18 | scanner-accessory-serial-number | 1 | 1 | Identifies the serial number for the scanner accessory. If this is a writable object, the POS should indicate the maximum support… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.19 | scanner-accessory-model-number | 1 | 1 | Model number of the scanner accessory. This string should only use characters from the US-ASCII code set. Additional information… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.20 | scanner-accessory-adf-sheet-count | 1 | 1 | Total number of sheets that have been fed through the Automatic Document Feed (ADF) accessory. Additional information: The Automat… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.21 | scanner-accessory-flatbed-scan-count | 1 | 1 | Total number of scans performed by a flatbed scanner accessory. Additional information: The count is only incremented when a sheet… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.22 | scanner-accessory-cleaning-interval | 1 | 1 | Recommended cleaning interval in units of sheets scanned. Additional information: Recommended cleaning interval is in units of she… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.23 | scanner-accessory-cleaning-count | 1 | 1 | The number of sheets scanned since the last cleaning was performed. Additional information: The number of sheets that have gone th… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.24 | scanner-accessory-maintenance-interval | 1 | 1 | Recommended maintenance interval in units of sheets scanned. Additional information: Recommended maintenance interval is in units … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.25 | scanner-accessory-maintenance-count | 1 | 1 | The number of sheets scanned since the last maintenance was performed. Additional information: The number of sheets that have gone… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.26 | scanner-accessory-rom-revision | 1 | 1 | ROM revision of the scanner accessory firmware. Additional information: ROM revision of the Fujitsu scanner is downloaded from the… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.27 | scanner-accessory-copy-processor-boot-revision | 1 | 1 | Boot ROM revision of scanner copy processor firmware. Boot code to initialize the copy processor, establish communications with t… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.28 | scanner-accessory-copy-processor-runtime-revision | 1 | 1 | Revision of the runtime firmware for the scanner copy processor. Runtime code which retrieves scanned data from the scanner and … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.29 | scanner-accessory-service-agent-revision | 1 | 1 | Revision of scanner service agent firmware. Service agent which accepts scanned data and processes scanner copy processor reques… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.30 | scanner-accessory-control-panel-user-interface-revision | 1 | 1 | Revision of the control panel user interface firmware. Additional information: Revision of the copy processor user interface firmw… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.32 | scan-calibration | 1 | 2 | None |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.33 | scanner-accessory-nvram | 1 | 1 | Returns the contents of the NVRAM (Non-Volatile RAM) located in the scanner accessory. Additional information: Read bytes 0..39 of… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.34 | scanner-accessory-nvram2 | 1 | 1 | Returns the second part of the contents of the NVRAM (Non-Volatile RAM) located in the scanner accessory. Additional information:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.35 | scanner-accessory-nvram3 | 1 | 1 | Returns the third part of the contents of the NVRAM (Non-Volatile RAM) located in the scanner accessory. Additional information: R… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.36 | scanner-accessory-nvram4 | 1 | 1 | Returns the fourth part of the contents of the NVRAM (Non-Volatile RAM) located in the scanner accessory. Additional information:… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.37 | ui-add-option | 1 | 1 | Lets the host application set up target (eg.scan) destinations. The destinations can be a host network address and/or an applicat… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.38 | ui-select-option | 1 | 1 | Triggers a job from the device based on the option selected. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.42 | ui-delete-option | 1 | 1 | Lets the host application delete target eg. scan destinations that were setup with UI-ADD-OPTION. The host sends down the entire … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.43 | scanner-jam-page-count | 1 | 1 | Indicates a count of the total pages jammed in the scanner'slifetime. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.44 | scanner-adf-page-count | 1 | 1 | Indicates a count of the total pages scanned through the ADF on the device. This may include scan to host jobs, copyjobs, and fa… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.45 | scan-adf-page-count | 1 | 1 | Indicates the total pages scanned through the ADF to the host from the device. If the total pages scanned through the scanner ar… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.46 | scan-image-type | 1 | 1 | Indicates the image type of the scan data. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.47 | scan-subsample | 1 | 1 | Indicates the subsampling used for Scan Data. 4:1:1, 4:2:2, and 4:3:3 subsampling are used to modify the scan image quality and … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.48 | scanner-retrieve-scanline | 1 | 1 | This object facilitates the sending of a scan line of data from the scanner to a host. It grabs either raw or corrected data. SE… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.49 | scanner-motor-control | 1 | 1 | This objects is set to the number of steps that the scan motor should move. SERVICE-PASSWORD must be setcorrectly to use this ob… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.50 | scan-height | 1 | 1 | Used to set the height of a scan image in Decapoints. The use of Decapoints as units of measure eliminates the need for the use… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.51 | scanner-scanline-statistics | 1 | 1 | This object is used to obtain statistics about the scan line that was previously obtained using the SCANNER-RETRIEVE-SCANLINE obj… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.53 | scan-gamma-correction | 1 | 1 | A 32-bit quantity that indicates the gamma correction to use on the scan image. The first 16 bits indicate the integral portion o… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.54 | scan-pad-image | 1 | 1 | Indicates if the scan image should be padded with white data or not. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.63 | scanner-accessory-total-copy-pages-printed | 1 | 1 | This relates to the number of copy pages printed on a device. The output sheet that is duplexed (made 2-sided) should be counted… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.73 | scan-flatbed-page-count | 1 | 1 | This object tracks the page count for the pages scanned from the flatbed. |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.74 | scanner-flatbed-page-count | 1 | 1 | This object tracks the page count for the pages scanned for all jobs from the flatbed. This includes scan to host jobs, fax jobs… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.75 | scanner-modular-hardware | 1 | 1 | Used to specify whether optional hardware is installed or not Additional information: HP LaserJet 3300 Series uses this object to … |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.76 | default-scanner-margin-top | 1 | 1 | Sets the top scanner margin. The unit of measure should be documented in the device POS. Additional information: This object is a… |
| 1.3.6.1.4.1.11.2.3.9.4.2.1.2.2.1.77 | scan-max-line-width | 1 | 1 | Returns the maximum scan line width in pixels for the currently selected resolution. Additional information: Returns the maximum s… |