This object accepts two values, enabled (1), and disabled (2).
When the value is disabled, the SPVC is not connected. When
enabled, the SPVC is connected when possible.
Use nncCrSpvpcAdminStatus to determine if the connection is
successful.
Parsed from file NncExtSPVC.mib.txt
Company: None
Module: NNCEXTSPVC-MIB
This object accepts two values, enabled (1), and disabled (2).
When the value is disabled, the SPVC is not connected. When
enabled, the SPVC is connected when possible.
Use nncCrSpvpcAdminStatus to determine if the connection is
successful.
Parsed from file NNCEXTSPVC-MIB.mib
Module: NNCEXTSPVC-MIB
Vendor: Newbridge Networks Corporation
Module: NNCEXTSPVC-MIB
[Automatically extracted from oidview.com]
nncCrSpvpcAdminStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object accepts two values, enabled (1), and disabled (2). When the value is disabled, the SPVC is not connected. When enabled, the SPVC is connected when possible. Use nncCrSpvpcAdminStatus to determine if the connection is successful." ::= { nncCrSpvpcTableEntry 4 }
nncCrSpvpcAdminStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object accepts two values, enabled (1), and disabled (2). When the value is disabled, the SPVC is not connected. When enabled, the SPVC is connected when possible. Use nncCrSpvpcAdminStatus to determine if the connection is successful." ::= { nncCrSpvpcTableEntry 4 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.123.3.82.1.1.1.1 | nncCrSpvpcServiceCategory | 0 | 0 | This object is used to set the traffic service category. This object is dependent on the value specified in nncCrSpvpcTrafficDe… |
1.3.6.1.4.1.123.3.82.1.1.1.2 | nncCrSpvpcTargEpAddr | 0 | 0 | This object is used to specify the 20 byte AESA address for the target endpoint. The address map is as the following: Byte\Bit … |
1.3.6.1.4.1.123.3.82.1.1.1.3 | nncCrSpvpcTargVpi | 0 | 0 | This object contains the virtual path identifier (VPI) value for the target endpoint. Range: 0 - 4095 |
1.3.6.1.4.1.123.3.82.1.1.1.5 | nncCrSpvpcPriority | 0 | 0 | This object is used to set the priority for a SPVC connection request. It ranges between 1-16, with the following values: Best Pr… |
1.3.6.1.4.1.123.3.82.1.1.1.6 | nncCrSpvpcMaxAdminWeight | 0 | 0 | This object is used to set a cost threshold for an SPVC connection. If the total cost of all VPCs exceeds this weight value for … |
1.3.6.1.4.1.123.3.82.1.1.1.7 | nncCrSpvpcOperation | 0 | 0 | This object is used to request a reroute operation. Querying this object will not provide any useful information. |
1.3.6.1.4.1.123.3.82.1.1.1.8 | nncCrSpvpcCallStatus | 0 | 0 | This read-only object is used to query the state of a particular SPVC. SPVCs that are connected and operational will return a va… |
1.3.6.1.4.1.123.3.82.1.1.1.9 | nncCrSpvpcLocRerouteConfig | 0 | 0 | This object is used to configure the 'reroute on loss of continuity' feature using OAM-CC cells. It can be configured for eithe… |
1.3.6.1.4.1.123.3.82.1.1.1.10 | nncCrSpvpcFwdAbrDynTrfcIcr | 0 | 0 | ABR dynamic traffic descriptor's Initial Cell (Information) Rate for the forward direction. Range: 0 - 2488320 Kb/s |
1.3.6.1.4.1.123.3.82.1.1.1.11 | nncCrSpvpcFwdAbrDynTrfcRif | 0 | 0 | ABR traffic Rate Increase Factor for the forward direction. Value is expressed as the -power of 2. Range: 0 - 9 |
1.3.6.1.4.1.123.3.82.1.1.1.12 | nncCrSpvpcFwdAbrDynTrfcRdf | 0 | 0 | ABR traffic Rate Decrease Factor descriptor for the forward direction. Value is expressed as the -power of 2 Range: 0 - 9 |
1.3.6.1.4.1.123.3.82.1.1.1.13 | nncCrSpvpcBwdAbrDynTrfcIcr | 0 | 0 | ABR dynamic traffic descriptor's Initial Cell Rate for the destination endpoint. Range: 0 - 2488320 Kb/s |
1.3.6.1.4.1.123.3.82.1.1.1.14 | nncCrSpvpcBwdAbrDynTrfcRif | 0 | 0 | ABR traffic Rate Increase Factor for the backward direction. Value is expressed as the -power of 2. Range: 0 - 9 |
1.3.6.1.4.1.123.3.82.1.1.1.15 | nncCrSpvpcBwdAbrDynTrfcRdf | 0 | 0 | ABR traffic Rate Decrease Factor descriptor for the backward direction. Value is expressed as the -power of 2 Range: 0 - 9 |
1.3.6.1.4.1.123.3.82.1.1.1.16 | nncCrSpvpcSrcBillingFlag | 0 | 0 | Billing Configuration for the source endpoint |
1.3.6.1.4.1.123.3.82.1.1.1.17 | nncCrSpvpcFwdTmTrafficDescriptor | 0 | 0 | This object contains the traffic descriptor for the SPVC. Tag All (1) (UBR using 2k/12k fabric only) P_0+1 (2) (C… |
1.3.6.1.4.1.123.3.82.1.1.1.18 | nncCrSpvpcFwdTmPolicingOption | 0 | 0 | Policing Option for an SPVPC. tag is supported only on rt-VBR/nrt-VBR connections that use the P_0+1/S_0 traffic descriptor |
1.3.6.1.4.1.123.3.82.1.1.1.19 | nncCrSpvpcFwdTmBucketOneRate | 0 | 0 | This object is for peak cell rate (PCR), the cell rate which the source may never exceed. It is used to determine which cells ar… |
1.3.6.1.4.1.123.3.82.1.1.1.20 | nncCrSpvpcFwdTmBucketOneCdvt | 0 | 0 | This object is used to set cell delay variation tolerance (CDVT) for one endpoint, measured in microseconds. Range: 1 - 190,000 m… |
1.3.6.1.4.1.123.3.82.1.1.1.21 | nncCrSpvpcFwdTmBucketTwoRate | 0 | 0 | SIR_0p, SIR_0+1p or MIR_0+1p. This parameter holds the sustained information rate for VBR traffic, and the minimum information r… |
1.3.6.1.4.1.123.3.82.1.1.1.22 | nncCrSpvpcFwdTmBucketTwoMbs | 0 | 0 | This object is for the maximum burst size, in cells, for SIR_0p or SIR_0+1p (nrtVbr and rtVbr only). Range: 1 - 10000 cells |
1.3.6.1.4.1.123.3.82.1.1.1.23 | nncCrSpvpcFwdTmCdv | 0 | 0 | This value is to set the cell delay variation (CDV) between two endpoints to support the rt-VBR service category. Range: 250-1000… |
1.3.6.1.4.1.123.3.82.1.1.1.24 | nncCrSpvpcFwdTmClr | 0 | 0 | The object is to set the cell loss ratio (CLR) between two SPVC endpoints when using the nrt-VBR service category. Value set as 1… |
1.3.6.1.4.1.123.3.82.1.1.1.25 | nncCrSpvpcBwdTmTrafficDescriptor | 0 | 0 | This object contains the traffic descriptor for the SPVC. Tag All (1) (UBR using 2k/12k fabric only) P_0+1 (2) (C… |
1.3.6.1.4.1.123.3.82.1.1.1.26 | nncCrSpvpcBwdTmPolicingOption | 0 | 0 | Policing Option for an SPVPC. tag is supported only on rt-VBR/nrt-VBR connections that use the P_0+1/S_0 traffic descriptor |
1.3.6.1.4.1.123.3.82.1.1.1.27 | nncCrSpvpcBwdTmBucketOneRate | 0 | 0 | This object is for peak information rate (PIR), the cell rate which the source may never exceed. It is used to determine which c… |
1.3.6.1.4.1.123.3.82.1.1.1.28 | nncCrSpvpcBwdTmBucketOneCdvt | 0 | 0 | This object is used to set cell delay variation tolerance (CDVT) for one endpoint, measured in microseconds. Range: 1 - 190,000 m… |
1.3.6.1.4.1.123.3.82.1.1.1.29 | nncCrSpvpcBwdTmBucketTwoRate | 0 | 0 | SIR_0p, SIR_0+1p or MIR_0+1p. This parameter holds the sustained information rate for VBR traffic, and the minimum information r… |
1.3.6.1.4.1.123.3.82.1.1.1.30 | nncCrSpvpcBwdTmBucketTwoMbs | 0 | 0 | This object is for the maximum burst size, in cells, for SIR_0p or SIR_0+1p (nrtVbr and rtVbr only). Range: 1 - 10000 cells |
1.3.6.1.4.1.123.3.82.1.1.1.31 | nncCrSpvpcBwdTmCdv | 0 | 0 | This value is to set the cell delay variation (CDV) between two endpoints to support the rt-VBR service category. Range: 250-1000… |
1.3.6.1.4.1.123.3.82.1.1.1.32 | nncCrSpvpcBwdTmClr | 0 | 0 | The object is to set the cell loss ratio (CLR) between two SPVC endpoints when using the nrt-VBR service category. Value set as 1… |
1.3.6.1.4.1.123.3.82.1.1.1.33 | nncCrSpvpcCreator | 0 | 0 | The object retrieves the creator of a SPVC connection. |
1.3.6.1.4.1.123.3.82.1.1.1.34 | nncCrSpvpcRowStatus | 0 | 0 | This object is used to control the status of a PDU and to query the status of an SPVC. When the RowStatus value is 'createAndWa… |