ABR dynamic traffic descriptor's Initial Cell Rate for the
forward direction.
Range: 0 - 2488320 Kb/s
Parsed from file NncExtSPVC.mib.txt
Company: None
Module: NNCEXTSPVC-MIB
ABR dynamic traffic descriptor's Initial Cell Rate for the
forward direction.
Range: 0 - 2488320 Kb/s
Parsed from file NNCEXTSPVC-MIB.mib
Module: NNCEXTSPVC-MIB
Vendor: Newbridge Networks Corporation
Module: NNCEXTSPVC-MIB
[Automatically extracted from oidview.com]
nncCrSpvccFwdAbrDynTrfcIcr OBJECT-TYPE SYNTAX INTEGER (0..2488320) MAX-ACCESS read-create STATUS current DESCRIPTION "ABR dynamic traffic descriptor's Initial Cell Rate for the forward direction. Range: 0 - 2488320 Kb/s" DEFVAL { 1000 } ::= { nncCrSpvccTableEntry 14 }
nncCrSpvccFwdAbrDynTrfcIcr OBJECT-TYPE SYNTAX INTEGER (0..2488320) MAX-ACCESS read-create STATUS current DESCRIPTION "ABR dynamic traffic descriptor's Initial Cell Rate for the forward direction. Range: 0 - 2488320 Kb/s" DEFVAL { 1000 } ::= { nncCrSpvccTableEntry 14 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.123.3.82.1.3.1.1 | nncCrSpvccServiceCategory | 0 | 0 | This object is used to set the traffic service category. This object is dependent on the value specified in nncCrSpvccTrafficDe… |
| 1.3.6.1.4.1.123.3.82.1.3.1.2 | nncCrSpvccTargEpAddr | 0 | 0 | This object is used to specify the AESA address for the target endpoint. The mapping scheme is as follows: Byte\Bit 8 … |
| 1.3.6.1.4.1.123.3.82.1.3.1.3 | nncCrSpvccTargVpi | 0 | 0 | This object contains the virtual path identifier (VPI) value for the target endpoint. Range: 0 - 4095 |
| 1.3.6.1.4.1.123.3.82.1.3.1.4 | nncCrSpvccTargVci | 0 | 0 | This object contains the virtual channel identifier (VCI) value for the target endpoint. Range: 1 - 65535 |
| 1.3.6.1.4.1.123.3.82.1.3.1.5 | nncCrSpvccTargDlci | 0 | 0 | This object contains the data link connection identifier for a frame relay endpoint. This number is used to identify the target… |
| 1.3.6.1.4.1.123.3.82.1.3.1.6 | nncCrSpvccTargCeNumber | 0 | 0 | This object contains circuit number, channel group number or both for the Circuit Emulation endpoint. Used in CR to CE connectio… |
| 1.3.6.1.4.1.123.3.82.1.3.1.7 | nncCrSpvccTargEpType | 0 | 0 | This object specifies a target endpoint as one of the following types: cellRelay (1) frameRelay (2) circuitEmulation … |
| 1.3.6.1.4.1.123.3.82.1.3.1.8 | nncCrSpvccAdminStatus | 0 | 0 | This object accepts two values, enabled (1), and disabled (2). When the value is disabled, the SPVC is not connected. When enabl… |
| 1.3.6.1.4.1.123.3.82.1.3.1.9 | nncCrSpvccPriority | 0 | 0 | This object is used to set the priority for a SPVC connection request. It ranges between 1-16, with the following values: Best Pr… |
| 1.3.6.1.4.1.123.3.82.1.3.1.10 | nncCrSpvccMaxAdminWeight | 0 | 0 | This object is used to set a cost threshold for an SPVC connection. If the total cost of all VPCs exceeds this weight value for … |
| 1.3.6.1.4.1.123.3.82.1.3.1.11 | nncCrSpvccOperation | 0 | 0 | This object is used to request a reroute operation. Querying this object will not provide any useful information. |
| 1.3.6.1.4.1.123.3.82.1.3.1.12 | nncCrSpvccCallStatus | 0 | 0 | This read-only object is used to query the state of a particular SPVC. SPVCs that are connected and operational will return a va… |
| 1.3.6.1.4.1.123.3.82.1.3.1.13 | nncCrSpvccLocRerouteConfig | 0 | 0 | This object is used to configure the 'reroute on loss of continuity' feature using OAM-CC cells. It can be configured for eithe… |
| 1.3.6.1.4.1.123.3.82.1.3.1.15 | nncCrSpvccFwdAbrDynTrfcRif | 0 | 0 | ABR traffic Rate Increase Factor for the forward direction. Value is expressed as the -power of 2. Range: 0 - 9 |
| 1.3.6.1.4.1.123.3.82.1.3.1.16 | nncCrSpvccFwdAbrDynTrfcRdf | 0 | 0 | ABR traffic Rate Decrease Factor descriptor for the forward direction. Value is expressed as the -power of 2 Range: 0 - 9 |
| 1.3.6.1.4.1.123.3.82.1.3.1.17 | nncCrSpvccBwdAbrDynTrfcIcr | 0 | 0 | ABR dynamic traffic descriptor's Initial Cell Rate for the destination endpoint. Range: 0 - 2488320 Kb/s |
| 1.3.6.1.4.1.123.3.82.1.3.1.18 | nncCrSpvccBwdAbrDynTrfcRif | 0 | 0 | ABR traffic Rate Increase Factor for the backward direction. Value is expressed as the -power of 2. Range: 0 - 9 |
| 1.3.6.1.4.1.123.3.82.1.3.1.19 | nncCrSpvccBwdAbrDynTrfcRdf | 0 | 0 | ABR traffic Rate Decrease Factor descriptor for the backward direction. Value is expressed as the -power of 2 Range: 0 - 9 |
| 1.3.6.1.4.1.123.3.82.1.3.1.20 | nncCrSpvccSrcBillingFlag | 0 | 0 | Billing Configuration for the source endpoint |
| 1.3.6.1.4.1.123.3.82.1.3.1.21 | nncCrSpvccFwdTmTrafficDescriptor | 0 | 0 | This object contains the traffic descriptor for the SPVC. Tag All (1) (UBR using 2k/12k fabric only) P_0+1 (2) (C… |
| 1.3.6.1.4.1.123.3.82.1.3.1.22 | nncCrSpvccFwdTmPolicingOption | 0 | 0 | Policing Option for an SPVCC. tag is supported only on rt-VBR/nrt-VBR connections that use the P_0+1/S_0 traffic descriptor |
| 1.3.6.1.4.1.123.3.82.1.3.1.23 | nncCrSpvccFwdTmBucketOneRate | 0 | 0 | This object is for peak cell rate (PCR), the cell rate which the source may never exceed. It is used to determine which cells ar… |
| 1.3.6.1.4.1.123.3.82.1.3.1.24 | nncCrSpvccFwdTmBucketOneCdvt | 0 | 0 | This object is used to set cell delay variation tolerance (CDVT) for one endpoint, measured in microseconds. Range: 1 - 190,000 m… |
| 1.3.6.1.4.1.123.3.82.1.3.1.25 | nncCrSpvccFwdTmBucketTwoRate | 0 | 0 | SIR_0p, SIR_0+1p or MIR_0+1p. This parameter holds the sustained information rate for VBR traffic, and the minimum information r… |
| 1.3.6.1.4.1.123.3.82.1.3.1.26 | nncCrSpvccFwdTmBucketTwoMbs | 0 | 0 | This object is for the maximum burst size, in cells, for SIR_0p or SIR_0+1p (nrtVbr and rtVbr only). Range: 1 - 10000 cells |
| 1.3.6.1.4.1.123.3.82.1.3.1.27 | nncCrSpvccFwdTmCdv | 0 | 0 | This value is to set the cell delay variation (CDV) between two endpoints to support the rt-VBR service category. Range: 250-1000… |
| 1.3.6.1.4.1.123.3.82.1.3.1.28 | nncCrSpvccFwdTmClr | 0 | 0 | The object is to set the cell loss ratio (CLR) between two SPVC endpoints when using the nrt-VBR service category. Value set as 1… |
| 1.3.6.1.4.1.123.3.82.1.3.1.29 | nncCrSpvccFwdTmFrameDiscard | 0 | 0 | The Frame (AAL protocol data unit) Discard option. When enabled, cells are discarded at the frame level by examining the SDU-ty… |
| 1.3.6.1.4.1.123.3.82.1.3.1.30 | nncCrSpvccBwdTmTrafficDescriptor | 0 | 0 | This object contains the traffic descriptor for the SPVC. Tag All (1) (UBR using 2k/12k fabric only) P_0+1 (2) (C… |
| 1.3.6.1.4.1.123.3.82.1.3.1.31 | nncCrSpvccBwdTmPolicingOption | 0 | 0 | Policing Option for an SPVCC. tag is supported only on rt-VBR/nrt-VBR connections that use the P_0+1/S_0 traffic descriptor |
| 1.3.6.1.4.1.123.3.82.1.3.1.32 | nncCrSpvccBwdTmBucketOneRate | 0 | 0 | This object is for peak cell rate (PCR), the cell rate which the source may never exceed. It is used to determine which cells ar… |
| 1.3.6.1.4.1.123.3.82.1.3.1.33 | nncCrSpvccBwdTmBucketOneCdvt | 0 | 0 | This object is used to set cell delay variation tolerance (CDVT) for one endpoint, measured in microseconds. Range: 1 - 190,000 m… |
| 1.3.6.1.4.1.123.3.82.1.3.1.34 | nncCrSpvccBwdTmBucketTwoRate | 0 | 0 | SIR_0p, SIR_0+1p or MIR_0+1p. This parameter holds the sustained information rate for VBR traffic, and the minimum information r… |
| 1.3.6.1.4.1.123.3.82.1.3.1.35 | nncCrSpvccBwdTmBucketTwoMbs | 0 | 0 | This object is for the maximum burst size, in cells, for SIR_0p or SIR_0+1p (nrt-VBR and rt-VBR only). Range: 1 - 10000 cells |
| 1.3.6.1.4.1.123.3.82.1.3.1.36 | nncCrSpvccBwdTmCdv | 0 | 0 | This value is to set the cell delay variation (CDV) between two endpoints to support the rt-VBR service category. Range: 250-1000… |
| 1.3.6.1.4.1.123.3.82.1.3.1.37 | nncCrSpvccBwdTmClr | 0 | 0 | The object is to set the cell loss ratio (CLR) between two SPVC endpoints when using the nrt-VBR service category. Value set as 1… |
| 1.3.6.1.4.1.123.3.82.1.3.1.38 | nncCrSpvccBwdTmFrameDiscard | 0 | 0 | The Frame (AAL protocol data unit) Discard option. When enabled, cells are discarded at the frame level by examining the SDU-ty… |
| 1.3.6.1.4.1.123.3.82.1.3.1.39 | nncCrSpvccFrBwdTmAr | 0 | 0 | This object is used to specify the Access Rate, in Kb/s. |
| 1.3.6.1.4.1.123.3.82.1.3.1.40 | nncCrSpvccFrBwdTmCir | 0 | 0 | The committed Information Rate, in Kb/s. |
| 1.3.6.1.4.1.123.3.82.1.3.1.41 | nncCrSpvccFrBwdTmBc | 0 | 0 | The Committed Burst Size, in Kb. |
| 1.3.6.1.4.1.123.3.82.1.3.1.42 | nncCrSpvccFrBwdTmBe | 0 | 0 | The Excess Burst Size, in Kb. |
| 1.3.6.1.4.1.123.3.82.1.3.1.43 | nncCrSpvccFrBwdTmIwf | 0 | 0 | Interworking Function. Values: none (None (FR Switching) = 0) networkInterworking (Network Interworking = 2)… |
| 1.3.6.1.4.1.123.3.82.1.3.1.44 | nncCrSpvccFrBwdTmPo | 0 | 0 | Policing |
| 1.3.6.1.4.1.123.3.82.1.3.1.45 | nncCrSpvccFrBwdTmPacing | 0 | 0 | Pacing |
| 1.3.6.1.4.1.123.3.82.1.3.1.46 | nncCrSpvccFrBwdTmPtclMapping | 0 | 0 | Protocol Mapping for Service Interworking SPVCs. If Translated Service Interworking is selected, the a profile must be set using … |
| 1.3.6.1.4.1.123.3.82.1.3.1.47 | nncCrSpvccFrBwdTmClpMapping | 0 | 0 | Cell Loss Priority Mapping. Values: cLPEqualsDE (CLP = DE, 0) cLPEquals0 (CLP = 0, 1 ) cLPEquals1 (CLP = 1, 2 ) |
| 1.3.6.1.4.1.123.3.82.1.3.1.48 | nncCrSpvccFrBwdTmDeMapping | 0 | 0 | Discard Eligibility Mapping Values: dEEqualsCLP (DE = CLP, 0) dESSCSor0 (Network Interworking: DE=FR_SSCS Service Interworking… |
| 1.3.6.1.4.1.123.3.82.1.3.1.49 | nncCrSpvccFrBwdTmEfciMapping | 0 | 0 | Explicit Forward Congestion Indication Mapping (Applies only to Service Interworking (IWF3), FR to ATM) Values: eFCIEqualsFECN (EF… |
| 1.3.6.1.4.1.123.3.82.1.3.1.50 | nncCrSpvccFrBwdTmPvcMgntProfile | 0 | 0 | Enables or disables the PVC Management Profile. When enabled, LMI is enabled on the network-side of the connection. Used only with… |
| 1.3.6.1.4.1.123.3.82.1.3.1.51 | nncCrSpvccFrBwdTmSIWProfile | 0 | 0 | The FR-CR profile index for service interworking connections. This attribute is used to define the translation profile to use whe… |
| 1.3.6.1.4.1.123.3.82.1.3.1.52 | nncCrSpvccCreator | 0 | 0 | The object retrieves the creator of a SPVC connection. |
| 1.3.6.1.4.1.123.3.82.1.3.1.53 | nncCrSpvccRowStatus | 0 | 0 | This object is used to control the status of a PDU and to query the status of an SPVC. When the RowStatus value is 'createAndWa… |