If anxEnableSecurity is not set, this
parameter selects slip session logging. If
anxEnableSecurity is set, this parameter
permits slip access only from secure ports.
This MIB object corresponds to the NA/admin
asynchronous, ta and sync port parameter 'slip_ppp_security'.
Parsed from file xylo-wan.mib.txt
Company: avaya
Module: XYLO-WAN-MIB
Child arc 0 is used to translate between SNMPv1 and SNMPv2 notification parameters as explained in IETF RFC 2576, section 3.
gpNetSlipSecure OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "If anxEnableSecurity is not set, this parameter selects slip session logging. If anxEnableSecurity is set, this parameter permits slip access only from secure ports. This MIB object corresponds to the NA/admin asynchronous, ta and sync port parameter 'slip_ppp_security'." ::= { globals 67 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.15.2.12.2.67.0 | gpNetSlipSecure | 0 | 0 | None |
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.15.2.12.2.1 | gpGenericMode | 1 | 1 | This parameter defines the mode for access to the serial line or TA port. The default is cli. This MIB object corresponds to the … |
1.3.6.1.4.1.15.2.12.2.2 | gpGenericLocation | 1 | 1 | A descriptive string for a this port. This string is displayed by the CLI who command. This MIB object corresponds to the NA/ad… |
1.3.6.1.4.1.15.2.12.2.3 | gpGenericTermVar | 1 | 1 | A string defining the type of terminal attached to the serial/ta port. This MIB object corresponds to the NA/admin asynchronous/t… |
1.3.6.1.4.1.15.2.12.2.4 | gpGenericPrompt | 1 | 1 | This parameter defines a port-specific prompt string. The prompt string consists of displayable characters and embedded formatti… |
1.3.6.1.4.1.15.2.12.2.5 | gpGenericCliInterface | 1 | 1 | Specifies either a Unix or VMS command line interface. The default is uci. This MIB object corresponds to the NA/admin asynchrono… |
1.3.6.1.4.1.15.2.12.2.6 | gpGenericAllowBcast | 1 | 1 | Controls whether the serial/ta port can receive administrative broadcast messages. This MIB object corresponds to the NA/admin as… |
1.3.6.1.4.1.15.2.12.2.7 | gpGenericBcastDirection | 1 | 1 | Defines the direction that an administrative broadcast message is sent. This parameter is valid only when the port is defined as… |
1.3.6.1.4.1.15.2.12.2.8 | gpGenericImask7Bits | 1 | 1 | When enabled, instructs the Annex to ignore the eighth bit of all received characters on the port. This MIB object corresponds to… |
1.3.6.1.4.1.15.2.12.2.9 | gpGenericCliImask7 | 1 | 1 | Defines whether input at the CLI is masked to 7 bits. The default is disabled. This MIB object corresponds to the NA/admin async… |
1.3.6.1.4.1.15.2.12.2.10 | gpGenericBanner | 1 | 1 | Specifies whether the Annex banner and message- of-the-day are displayed on the port. The default is enabled. This has four possi… |
1.3.6.1.4.1.15.2.12.2.11 | gpGenericTcpKeepAlive | 1 | 1 | The default keep-alive value for connections to this serial port. If this is zero, use the value specified by anxTcpKeepAlive. T… |
1.3.6.1.4.1.15.2.12.2.12 | gpGenericDedicatedArgs | 1 | 1 | Command line arguments to be passed to process started by a dedicated port with mode set to 'telnet', 'tn3270', 'rlogin', 'connec… |
1.3.6.1.4.1.15.2.12.2.13 | gpGenericModemVar | 1 | 1 | A string defining the type of modem attached to the serial port. This object is not valid for TA ports. This MIB object correspond… |
1.3.6.1.4.1.15.2.12.2.14 | gpGenericDefSessMode | 1 | 1 | The default session mode when the DECServer command interface is configured. The default is interactive. This MIB object corres… |
1.3.6.1.4.1.15.2.12.2.15 | gpGenericResolveProtocol | 1 | 1 | Default host protocol to use when starting a dedicated port and the protocol is not explicitly specified in the command. Is set … |
1.3.6.1.4.1.15.2.12.2.17 | gpSignalInputStartChar | 1 | 1 | The control character sequence that restarts input if the charPortInFlowType parameter (in the char MIB) is set to xonXoff. This … |
1.3.6.1.4.1.15.2.12.2.18 | gpSignalInputStopChar | 1 | 1 | The control character sequence that stops input if the charPortInFlowType parameter (in the char MIB) is set to xonXoff. This val… |
1.3.6.1.4.1.15.2.12.2.19 | gpSignalOutputStartChar | 1 | 1 | The control character sequence that restarts output if the charPortOutFlowType parameter (in the char MIB) is set to xonXoff. Thi… |
1.3.6.1.4.1.15.2.12.2.20 | gpSignalOutputStopChar | 1 | 1 | The control character sequence that stops output if the charPortOutFlowType parameter (in the char MIB) is set to xonXoff. This v… |
1.3.6.1.4.1.15.2.12.2.21 | gpSignalIxanyFlowCtrl | 1 | 1 | This parameter specifies whether any input character will be treated as a start (xon) character when output has been suspended by… |
1.3.6.1.4.1.15.2.12.2.23 | gpSignalForwardKey | 1 | 1 | Defines a control character sequence as an attention character to switch the user to the next session. The Annex-II only allows a… |
1.3.6.1.4.1.15.2.12.2.24 | gpSignalBackwardKey | 1 | 1 | Defines a control character sequence as an attention character to switch the user to the previous session. The Annex-II only all… |
1.3.6.1.4.1.15.2.12.2.30 | gpLoginVciLoginPortPasswd | 1 | 1 | Enables the port password if the port is configured as a DECServer interface port. The default is disabled. This MIB object corre… |
1.3.6.1.4.1.15.2.12.2.31 | gpLoginVciLoginTimeout | 1 | 1 | Enables a login timer if the port is configured as a DECServer interface port. The default is disabled. This MIB object correspo… |
1.3.6.1.4.1.15.2.12.2.32 | gpTimerForwardTimer | 1 | 1 | This parameter defines the inter-character timer that sets the amount of time, in tens of milliseconds, that will elapse before fo… |
1.3.6.1.4.1.15.2.12.2.33 | gpTimerForwardCount | 1 | 1 | Specifies the number of received characters buffered for the port by the Annex before forwarding the characters to the host or net… |
1.3.6.1.4.1.15.2.12.2.34 | gpTimerCliInactivity | 1 | 1 | The amount of time, in minutes, that the Annex waits before hanging up the serial/ta port after it becomes idle. A value of 0 tu… |
1.3.6.1.4.1.15.2.12.2.35 | gpTimerInactivityTimer | 1 | 1 | The amount of time, in minutes, which a port can remain inactive before the Annex terminates all sessions and resets the port. A… |
1.3.6.1.4.1.15.2.12.2.36 | gpTimerInputIsActivity | 1 | 1 | Controls whether received input characters are considered as activity for the port. This MIB object corresponds to the NA/admin a… |
1.3.6.1.4.1.15.2.12.2.37 | gpTimerOutputIsActivity | 1 | 1 | Controls whether transmitted output characters are considered as activity for the port. This MIB object corresponds to the NA/ad… |
1.3.6.1.4.1.15.2.12.2.38 | gpTimerResetIdleTimer | 1 | 1 | Defines whether input or output resets the idle timer for the port. This MIB object corresponds to the NA/admin asynchronous/ta p… |
1.3.6.1.4.1.15.2.12.2.39 | gpTimerLongBreak | 1 | 1 | This parameter controls whether the Annex returns the user to the CLI prompt after receiving a break greater than two seconds. Th… |
1.3.6.1.4.1.15.2.12.2.40 | gpTimerShortBreak | 1 | 1 | This parameter controls whether the Annex returns the user to the CLI prompt after receiving a break shorter than two seconds. Th… |
1.3.6.1.4.1.15.2.12.2.41 | gpSecurityUserName | 1 | 1 | A string defining the default user name for the user of this serial/ta port. This MIB object corresponds to the NA/admin asynchro… |
1.3.6.1.4.1.15.2.12.2.42 | gpSecurityCli | 1 | 1 | This parameter controls whether security is enabled for the port. This MIB object corresponds to the NA/admin asynchronous/ta por… |
1.3.6.1.4.1.15.2.12.2.43 | gpSecurityConnect | 1 | 1 | This parameter controls whether the host-based security policy is enabled for access from the port to the network. This MIB objec… |
1.3.6.1.4.1.15.2.12.2.44 | gpSecurityPortServer | 1 | 1 | This parameter controls whether the host-based security policy is enabled for access to the port from the port server. This MIB o… |
1.3.6.1.4.1.15.2.12.2.45 | gpSecurityPortPasswd | 1 | 1 | This parameter defines a password for the port for local password protection. This MIB object corresponds to the NA/admin asynchr… |
1.3.6.1.4.1.15.2.12.2.46 | gpSecurityIpsoClass | 1 | 1 | Defines the IP security classification for packets sent and received on this port. The default value is none. This MIB object co… |
1.3.6.1.4.1.15.2.12.2.47 | gpSecurityIpx | 1 | 1 | Controls whether IPX security is enabled on this port. The default is disabled. This MIB object corresponds to the NA/admin asyn… |
1.3.6.1.4.1.15.2.12.2.48 | gpLineEditAttnChar | 1 | 1 | Defines a control character sequence as an attention character to return the user to the CLI prompt. The Annex-II only allows x … |
1.3.6.1.4.1.15.2.12.2.49 | gpLineEditEcho | 1 | 1 | This parameter controls whether the Annex echoes all characters as they are received from the port. This MIB object corresponds t… |
1.3.6.1.4.1.15.2.12.2.50 | gpLineEditTelnetEscape | 1 | 1 | Defines the control character that returns the user to the 'telnet:' prompt when running the CLI telnet command. This value of th… |
1.3.6.1.4.1.15.2.12.2.51 | gpLineEditTelnetCRLF | 1 | 1 | Defines what characters are transmitted out the port to the network when the End-of-Line character is sensed. 'enabled' means tra… |
1.3.6.1.4.1.15.2.12.2.52 | gpLineEditMapToLower | 1 | 1 | When enabled, the Annex translates all upper case characters to lower case as they are received from the port. This MIB object co… |
1.3.6.1.4.1.15.2.12.2.53 | gpLineEditMapToUpper | 1 | 1 | When enabled, the Annex translates all lower case characters to upper case as they are transmitted to the port. This MIB object c… |
1.3.6.1.4.1.15.2.12.2.54 | gpLineEditCharErase | 1 | 1 | This parameter controls whether the Annex echoes the character erase and word erase characters for a video terminal (enabled) or f… |
1.3.6.1.4.1.15.2.12.2.55 | gpLineEditEraseChar | 1 | 1 | Defines the character erase control character sequence. This value of this object can be either a single displayable character or… |
1.3.6.1.4.1.15.2.12.2.56 | gpLineEditLineErase | 1 | 1 | This parameter controls whether the Annex echoes the line erase character for a video terminal (enabled) or for a hard-copy termi… |
1.3.6.1.4.1.15.2.12.2.57 | gpLineEditEraseLine | 1 | 1 | Defines the line erase control character sequence. This value of this object can be either a single displayable character or two … |
1.3.6.1.4.1.15.2.12.2.58 | gpLineEditEraseWord | 1 | 1 | Defines the word erase control character sequence. This value of this object can be either a single displayable character or two … |
1.3.6.1.4.1.15.2.12.2.59 | gpLineEditHardwareTabs | 1 | 1 | When enabled, this parameter allows the Annex to expand ASCII tab characters. This MIB object corresponds to the NA/admin asynchr… |
1.3.6.1.4.1.15.2.12.2.60 | gpLineEditRedisplayLine | 1 | 1 | Defines the reprint line control character sequence. This value of this object can be either a single displayable character or tw… |
1.3.6.1.4.1.15.2.12.2.61 | gpLineEditToggleOutput | 1 | 1 | Defines the flush control character used to flush the output buffer. This value of this object can be either a single displayable… |
1.3.6.1.4.1.15.2.12.2.62 | gpLineEditNewLineTerm | 1 | 1 | This parameter controls whether a carriage return is echoed as just a carriage return (enabled), or whether the carriage return i… |
1.3.6.1.4.1.15.2.12.2.63 | gpNetLocalAddr | 1 | 1 | The Internet address for the Annex's side of the point-to-point (SLIP or PPP) link. This MIB object corresponds to the NA/admin a… |
1.3.6.1.4.1.15.2.12.2.64 | gpNetRemoteAddr | 1 | 1 | The Internet address for the host at the remote end of the point-to-point (SLIP or PPP) link. This MIB object corresponds to the … |
1.3.6.1.4.1.15.2.12.2.65 | gpNetPppDialupAddr | 1 | 1 | local(1) - The annex will get the PPP dialup addresses from the port parameters local_address and remote_address. acp(2) - The An… |
1.3.6.1.4.1.15.2.12.2.66 | gpNetMetric | 1 | 1 | This parameter defines the hop count to the remote end of the SLIP or PPP interface. Setting this object to 0 defaults to a value … |
1.3.6.1.4.1.15.2.12.2.68 | gpNetInactivity | 1 | 1 | The number of units allowed for serial protocol inactivity on the port. The type of unit, minutes or seconds, is defined by the … |
1.3.6.1.4.1.15.2.12.2.69 | gpNetDoCompression | 1 | 1 | When enabled, the Annex will attempt to negotiate TCP/IP header compression on this serial link. This MIB object corresponds to … |
1.3.6.1.4.1.15.2.12.2.70 | gpNetAllowCompression | 1 | 1 | When enabled, the Annex will allow TCP/IP header compression on this serial link only if the other end of the serial link initiat… |
1.3.6.1.4.1.15.2.12.2.71 | gpNetInactivityUnits | 1 | 1 | The type of units that are used for the port's net inactivity timer. See also the anxpNetInactivity object. The default value is… |
1.3.6.1.4.1.15.2.12.2.72 | gpSlipSubnetMask | 1 | 1 | The subnet mask for this SLIP interface. This MIB object corresponds to the NA/admin asynchronous/ta/sync port parameter 'subnet… |
1.3.6.1.4.1.15.2.12.2.73 | gpSlipMtuSize | 1 | 1 | Force the compressed SLIP interface to use a Maximum Transmission Unit (MTU) of either 1024 bytes (large) or 256 bytes (small). … |
1.3.6.1.4.1.15.2.12.2.74 | gpSlipNoIcmp | 1 | 1 | When enabled, the Annex will discard any ICMP packets directed to this SLIP link. This MIB object corresponds to the NA/admin asy… |
1.3.6.1.4.1.15.2.12.2.75 | gpSlipTos | 1 | 1 | When enabled, the Annex sends interactive traffic over this SLIP link before any other traffic. This MIB object corresponds to th… |
1.3.6.1.4.1.15.2.12.2.76 | gpPPPMru | 1 | 1 | This parameter defines the maximum receive unit in bytes. The default value is 1500. This MIB object corresponds to the NA/admin a… |
1.3.6.1.4.1.15.2.12.2.77 | gpPPPAcm | 1 | 1 | This parameter specifies which of the first 32 bytes (0x00, ... 0x1F) can be sent as clear text and which need to be escaped. A b… |
1.3.6.1.4.1.15.2.12.2.78 | gpPPPSecurityProto | 1 | 1 | Defines which security protocol will be used to authenticate the remote user. This parameter must be set and the Annex enable_sec… |
1.3.6.1.4.1.15.2.12.2.79 | gpPPPRemoteUser | 1 | 1 | The username used by the Annex to identify itself if the remote PPP peer asks for authentication. This MIB object corresponds to … |
1.3.6.1.4.1.15.2.12.2.80 | gpPPPRemotePasswd | 1 | 1 | The password used by the Annex to identify itself if the remote PPP peer asks for authentication. Reading this parameter will ret… |
1.3.6.1.4.1.15.2.12.2.81 | gpPPPNcp | 1 | 1 | A bitmask to set the PPP NCP Options: 0x0001 NCP_ALL 0x0002 NCP_IPCP 0x0004 NCP_ATCP 0x0008 NCP_IPXCP 0x0010 NCP_MP 0x0020 NCP_CCP 0x0… |
1.3.6.1.4.1.15.2.12.2.82 | gpPPPIpxNetwork | 1 | 1 | The IPX network number for an IPX PPP connection using this port. When the IPX PPP connection is established the network number w… |
1.3.6.1.4.1.15.2.12.2.83 | gpPPPIpxNode | 1 | 1 | The IPX node number for an IPX PPP connection using this port. The value of this object is a 12 digit hexadecimal number string re… |
1.3.6.1.4.1.15.2.12.2.84 | gpARAPGuest | 1 | 1 | If enabled, allows ARAP guest login service. This MIB object corresponds to the NA/admin asynchronous/ta port parameter 'at_gues… |
1.3.6.1.4.1.15.2.12.2.85 | gpARAPNodeid | 1 | 1 | The default AppleTalk node ID hint that is used by the Annex on this port. The address consists of two parts separated by a dot.… |
1.3.6.1.4.1.15.2.12.2.86 | gpARAPSecurity | 1 | 1 | Controls whether ACP service is enabled for this port when establishing an AppleTalk connection. This MIB object corresponds to t… |
1.3.6.1.4.1.15.2.12.2.87 | gpARAPV42BIS | 1 | 1 | Controls whether V.42bis compression is done during an ARAP session. This MIB object corresponds to the NA/admin asynchronous/ta … |
1.3.6.1.4.1.15.2.12.2.88 | gpTN3270PrinterHost | 1 | 1 | The IP address of the machine running a Berkeley-style lpd server. This MIB object corresponds to the NA/admin asynchronous/ta po… |
1.3.6.1.4.1.15.2.12.2.89 | gpTN3270PrinterName | 1 | 1 | A valid printer name contained in the /etc/printcap file on the remote host. This MIB object corresponds to the NA/admin asynchro… |
1.3.6.1.4.1.15.2.12.2.90 | gpLATAuthMap | 1 | 1 | This port parameter is functionally identical to anxpLatAuthGroupVal and corresponds to the NA/admin Annex parameter 'group_value… |
1.3.6.1.4.1.15.2.12.2.91 | gpLATbEnable | 1 | 1 | Controls interpretation of LAT Data-B packets received from host. This MIB object corresponds to the NA/admin asynchronous/ta por… |
1.3.6.1.4.1.15.2.12.2.92 | gpLATMultiSession | 1 | 1 | This parameter allows multisession operation to be managed on a per port basis. If multisessions for the server has not been enab… |
1.3.6.1.4.1.15.2.12.2.94 | gpcharPortInFlowType | 1 | 1 | The port's type of input flow control. 'none' indicates no flow control at this level or below. 'xonXoff' indicates software flo… |
1.3.6.1.4.1.15.2.12.2.95 | gpcharPortOutFlowType | 1 | 1 | The port's type of output flow control. 'none' indicates no flow control at this level or below. 'xonXoff' indicates software fl… |
1.3.6.1.4.1.15.2.12.2.96 | gpcharPortSessionMaximum | 1 | 1 | The maximum number of concurrent sessions allowed on the port. A value of -1 indicates no maximum. Setting the maximum to less t… |
1.3.6.1.4.1.15.2.12.2.97 | gprs232AsyncPortBits | 1 | 1 | The port's number of bits in a character. This object corresponds to the admin parameter data_bits |
1.3.6.1.4.1.15.2.12.2.98 | gprs232AsyncPortStopBits | 1 | 1 | The port's number of stop bits. This object corresponds to the admin parameter stop_bits |
1.3.6.1.4.1.15.2.12.2.99 | gprs232AsyncPortParity | 1 | 1 | The port's sense of a character parity bit. |
1.3.6.1.4.1.15.2.12.2.101 | gpV120Mru | 1 | 1 | This parameter defines the maximum receive unit in bytes. The default value is 256. This MIB object corresponds to the NA/admin as… |
1.3.6.1.4.1.15.2.12.2.102 | gpMpMrru | 1 | 1 | This parameter sets the upper limit of the MRRU LCP negotiation. All LCP negotiations will start with this value; negotiation down… |
1.3.6.1.4.1.15.2.12.2.103 | gpMpEndPointClass | 1 | 1 | This parameter sets the preference for the Endpoint Discriminator. PPP Magic Number Block(5) isexcluded; it doesn't guarantee uniq… |
1.3.6.1.4.1.15.2.12.2.104 | gpMpEndPointValue | 1 | 1 | This parameter sets the value of the Endpoint Discriminator for options that require user-configured information. This parameter i… |
1.3.6.1.4.1.15.2.12.2.105 | gpProxyArpEnable | 1 | 1 | Specifies whether the Annex will proxy ARP all remote IP connections. A value of enabled(1) will allow the Annex to proxy all rem… |
1.3.6.1.4.1.15.2.12.2.106 | gpPPPTraceLevel | 1 | 1 | Controls whether PPP trace messages are sent to the syslog facility or not. The default value is none(0). This MIB object corres… |