Remove will free bus bandwidth used by
the INL, and disconnect all channels connected
over the INL. It will also set the INL start
mode in the configuration MIB to off.
Insert on a removed INL will get the new MIB
and software, and set the INL start mode in
the configuration MIB to automatic.
Reset is equivalent to a remove and insert,
except it does not change the INL start mode
in the configuration MIB.
Restart will reestablish the INL without
loading in the current INL configuration
MIB. All channels connected over the INL
will be disconnected.
Update will load the non-intrusive parameters
from the INL configuration MIB. If any
intrusive parameters have been changed, then
update will fail. Update will not affected the
channels connected over the INL.
Disable will prevent any new channel
connections from being made over an INL. It
will not affect existing channel connections.
Enable on an disabled INL will allow new
channel connections to be made over the INL.
Parsed from file STMIB.mib.txt
Company: None
Module: STMIB
Remove will free bus bandwidth used by
the INL, and disconnect all channels connected
over the INL. It will also set the INL start
mode in the configuration MIB to off.
Insert on a removed INL will get the new MIB
and software, and set the INL start mode in
the configuration MIB to automatic.
Reset is equivalent to a remove and insert,
except it does not change the INL start mode
in the configuration MIB.
Restart will reestablish the INL without
loading in the current INL configuration
MIB. All channels connected over the INL
will be disconnected.
Update will load the non-intrusive parameters
from the INL configuration MIB. If any
intrusive parameters have been changed, then
update will fail. Update will not affected the
channels connected over the INL.
Disable will prevent any new channel
connections from being made over an INL. It
will not affect existing channel connections.
Enable on an disabled INL will allow new
channel connections to be made over the INL.
Parsed from file STMIB.mib
Module: STMIB
Vendor: Timeplex
Module: STMIB
[Automatically extracted from oidview.com]
restINLDiagnostics OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2), insert(4), remove(5), reset(6), update(7), restart(79), setLoopback(9), clearLoopback(8), clearINLTotalCRCErrors(63), clearINLBERWindowFill(64) } ACCESS write-only STATUS mandatory DESCRIPTION "Remove will free bus bandwidth used by the INL, and disconnect all channels connected over the INL. It will also set the INL start mode in the configuration MIB to off. Insert on a removed INL will get the new MIB and software, and set the INL start mode in the configuration MIB to automatic. Reset is equivalent to a remove and insert, except it does not change the INL start mode in the configuration MIB. Restart will reestablish the INL without loading in the current INL configuration MIB. All channels connected over the INL will be disconnected. Update will load the non-intrusive parameters from the INL configuration MIB. If any intrusive parameters have been changed, then update will fail. Update will not affected the channels connected over the INL. Disable will prevent any new channel connections from being made over an INL. It will not affect existing channel connections. Enable on an disabled INL will allow new channel connections to be made over the INL." ::= { restINLEntry 3 }
restINLDiagnostics OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2), insert(4), remove(5), reset(6), update(7), restart(79), setLoopback(9), clearLoopback(8), clearINLTotalCRCErrors(63), clearINLBERWindowFill(64) } ACCESS write-only STATUS mandatory DESCRIPTION "Remove will free bus bandwidth used by the INL, and disconnect all channels connected over the INL. It will also set the INL start mode in the configuration MIB to off. Insert on a removed INL will get the new MIB and software, and set the INL start mode in the configuration MIB to automatic. Reset is equivalent to a remove and insert, except it does not change the INL start mode in the configuration MIB. Restart will reestablish the INL without loading in the current INL configuration MIB. All channels connected over the INL will be disconnected. Update will load the non-intrusive parameters from the INL configuration MIB. If any intrusive parameters have been changed, then update will fail. Update will not affected the channels connected over the INL. Disable will prevent any new channel connections from being made over an INL. It will not affect existing channel connections. Enable on an disabled INL will allow new channel connections to be made over the INL." ::= { restINLEntry 3 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.16.101.1.2.2.7.1.1 | restINLNumber | 0 | 0 | None |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.2 | restINLAddr | 0 | 0 | None |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.4 | restINLStatus | 0 | 0 | None |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.5 | restINLSubStatus | 0 | 0 | None |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.6 | restINLLocalBERLevel | 0 | 0 | BER level on the local node. If the local BER quality value is notCalculatedYet, then this attribute will return zero. |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.7 | restINLLocalBERQuality | 0 | 0 | None |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.8 | restINLRemoteNodeID | 0 | 0 | Node number that the INL terminates on. If no remote connection has been established, then this attribute will return zero. |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.9 | restINLRemotePortAddr | 0 | 0 | Port or bundle address that the INL terminates on. If no remote connection has been established, then this attribute will return z… |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.10 | restINLRemoteINLID | 0 | 0 | INL ID on the remote node that the INL terminates on. If no remote connection has been established, then this attribute will retur… |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.11 | restINLRemoteBERLevel | 0 | 0 | BER level on the remote node that the INL terminates on. If the remote BER quality value is notCalculatedYet, then this attribute… |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.12 | restINLRemoteBERQuality | 0 | 0 | None |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.13 | restINLAvailableTDMBw | 0 | 0 | None |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.14 | restINLAvailablePacketBw | 0 | 0 | None |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.15 | restINLLoopbackDuration | 0 | 0 | Value 65535 specifies a permanent loopback. |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.16 | restINLLoopbackStatus | 0 | 0 | None |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.17 | restINLTotalCRCErrors | 0 | 0 | None |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.18 | restINLBERWindowFill | 0 | 0 | Format e.g. 10/32, 5/32. |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.19 | restINLNumTdmCh | 0 | 0 | None |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.20 | restINLNumFrCh | 0 | 0 | None |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.21 | restINLSpeed | 0 | 0 | None |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.22 | restINLNumSaf | 0 | 0 | None |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.23 | restINLLOSMode | 0 | 0 | None |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.24 | restINLBusFrameMode | 0 | 0 | None |