The Super Tandem feature provides end to end compression over multiple hops,
solving the double compression problem detected in Voice compressing systems.
The Super Tandem allows transmission of compressed voice between a few
Vmux 2100 hubs, and eliminates the need to decompress an recompress it over
each voice card and PBX, thus improving voice quality and reducing delay.
Parsed from file OPTIMUX-MIB.mib
Module: OPTIMUX-MIB
ip2IfSuperTandem OBJECT-TYPE SYNTAX INTEGER { notApplicable (1), disable (2), enable (3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The Super Tandem feature provides end to end compression over multiple hops, solving the double compression problem detected in Voice compressing systems. The Super Tandem allows transmission of compressed voice between a few Vmux 2100 hubs, and eliminates the need to decompress an recompress it over each voice card and PBX, thus improving voice quality and reducing delay." ::= { ip2IfEntry 36 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.164.3.1.6.7.1.1.1 | ip2IfChannelIndex | 0 | 0 | The channel index, which is actualy the bundle ID. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.2 | ip2IfRowStatus | 0 | 0 | This parameter allows NMS to create/delete entries of this table. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.3 | ip2IfOperStatus | 0 | 0 | The actual link status. remoteFail - No Rx. localFail - No Tx. unavailable - No echo replay or replay with invalid code or when c… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.4 | ip2IfAdminStatus | 0 | 0 | The desired state of the link. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.5 | ip2IfDestAddr | 0 | 0 | The destination IP address. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.6 | ip2IfNextHop | 0 | 0 | The next hop to which the frame should be sent. Default value - 0.0.0.0. Upon setting the default value the frame is sent to the d… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.7 | ip2IfDestPort | 0 | 0 | The destination Bundle at the far-end device. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.8 | ip2IfMacAddr | 0 | 0 | The Destination MAC address of the next hop or destination station. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.9 | ip2IfJitterBuffer | 0 | 0 | The maximum cell arrival jitter in 10 usec that the reassembly process will tolerate in the cell stream, without producing errors… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.10 | ip2IfTos | 0 | 0 | The TOS (Type of Service) value: 0..255. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.11 | ip2IfTDMBytesInFrame | 0 | 0 | The number of TDM bytes to be placed in a single IP frame payload. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.12 | ip2IfVlanSupport | 0 | 0 | VLAN support (Tagging). no - No support to VLAN. yes - 4 VLAN bytes will be added to the frame. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.13 | ip2IfVlanIdentifier | 0 | 0 | VLAN ID. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.14 | ip2IfVlanFramePriority | 0 | 0 | VLAN Frame priority. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.15 | ip2IfExitPort | 0 | 0 | This object determines to which external port the traffic will be sent. auto - the device will decide automatically the exit port. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.16 | ip2IfVoiceOos | 0 | 0 | Voice Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.17 | ip2IfDataOos | 0 | 0 | Data Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.18 | ip2IfBundleUsage | 0 | 0 | The Bundle Resource usage in Kbps. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.19 | ip2IfOAM | 0 | 0 | This parameter determine the OAM configuration. The LSB (Bit 0 the most right one) is used for OAM connectivity. Values: 0 = disa… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.20 | ip2IfTDMoIpMode | 0 | 0 | The TDMoIP Mode configuration. Static- means TS can Tx any time. dynamicLES - means TS can Tx only when line is enabled accordin… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.21 | ip2IfTimeElapsed | 0 | 0 | The number of seconds that have elapsed since the beginning of the current error-measurement period. If, for some reason, such a… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.22 | ip2IfValidIntervals | 0 | 0 | The number of previous intervals for which data was collected. The value will be 96 unless the interface was brought online with… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.23 | ip2IfFarEndType | 0 | 0 | This object defines the type of the Far-End device. This data is important for signaling. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.24 | ip2IfRdnState | 0 | 0 | This object defines the role this bundle plays in the redundancy scheme: none(2) - means this bundle is not part of redundancy p… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.25 | ip2IfSourceAddr | 0 | 0 | Source IP Address of the bundle. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.26 | ip2IfBandWidth | 0 | 0 | Number of Time Slots in The Bundle. For T1 the value will be: 1..24 For E1 the value will be: 1..31 For T3 the value will be: 1..… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.27 | ip2IfMeasuredSilence | 0 | 0 | This object shows the percentage of Silence that was measured by the device for the current bundle. Relevant values: 0..100, 255.… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.28 | ip2IfPayloadType | 0 | 0 | This object defines the TDMoIP payload type. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.29 | ip2IfProtocolVersion | 0 | 0 | This object defines the TDMoIP protocol Version. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.30 | ip2IfTdmBackUpNextHop | 0 | 0 | Defines the TDM bundle default router in case there was a switch from the Primary Link (for example an ETH port) to a TDM backup… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.31 | ip2IfOosTxEnable | 0 | 0 | This object defines whether OOS will be Transmitted. Note that for IPmux1000 the Lbit is always sent, but the OOS will be sent ac… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.32 | ip2IfConnCheckPktFrequency | 0 | 0 | Time in sec. between 2 Bundle Connectivity Check packets. Valid values: 0..60. 0 = Not Applicable. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.33 | ip2IfConnPktTimeOutCycles | 0 | 0 | No. of cycles the agent will send Bundle Connectivity packets without receiving a response from the remote device before declari… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.34 | ip2IfMfRelay | 0 | 0 | Multi Frequency Signaling Detection. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.35 | ip2IfTxGain | 0 | 0 | Transmit gain in dBm. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.37 | ip2IfSrcPort | 0 | 0 | The source Bundle at the local device, this parameter used for cases where there is no match between ip2IfChannelIndex and the So… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.38 | ip2IfModemCalls | 0 | 0 | This MIB object shows whether Modem Calls are enabled via the bundle. relay option (3) means that the bundle will send to the ne… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.39 | ip2IfMinPulseWidth | 0 | 0 | Indicates the minimum width in milliseconds of the MF (Multi Frequency) tone transmitted by the switch. Valid values: 45-300 msec… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.40 | ip2IfMinPowerLevel | 0 | 0 | Indicates the minimum power level in dBm of the MF (Multi Frequency) tone transmitted by the switch. Valid values: -1...-35 dBm. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.41 | ip2IfEchoCanceler | 0 | 0 | Echo canceler activation. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.42 | ip2IfCodingLaw | 0 | 0 | This attribute indicates the Method/Law for decoding/encoding the voice information. aLaw(1) is the standard Law for E1 links. uLa… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.43 | ip2IfCustomToneDetect | 0 | 0 | Custom Tone Detection (COT) is a Control operation of a 2Khz tone detector. This tone is sent between PBX devices in order to ch… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.44 | ip2IfCallerIdDelay | 0 | 0 | Time in msec between CLID (Caller ID) signal detection on the line and CLID signal transmission. The CLID must be sent between r… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.45 | ip2IfConnectivityMode | 0 | 0 | This MIB object shows whether to send Pings or OAM frames over the bundle. |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.53 | ip2IfMfcSpoofing | 0 | 0 | This MIB object defines whether the MFC (Multi Frequency Compelled) protocol spoofing will exist in the bundle. When the MFC Spo… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.54 | ip2IfToneAckInterval | 0 | 0 | Time Interval in milli seconds from the time a Vmux sends tone/s to a local PBX until it receives an acknowledgement from this P… |
| 1.3.6.1.4.1.164.3.1.6.7.1.1.56 | ip2IfNoiseLevelForVAD | 0 | 0 | This object defines the Level of Noise on the line, the Voice Activation Detector (VAD) will have to handle. |