An entry in the T1/E1 port configuration table.
Parsed from file Rad0485.MIB.txt
Company: None
Module: RAD-MIB
An entry in the T1/E1 port configuration table.
Parsed from file RAD-MIB.mib
Module: RAD-MIB
Vendor: Rad Data Communications Ltd.
Module: DACS-MIB
[Automatically extracted from oidview.com]
prtT1E1CnfgEntry OBJECT-TYPE SYNTAX PrtT1E1CnfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " An entry in the T1/E1 port configuration table." INDEX { prtT1E1CnfgIdx, prtT1E1PrtIdx } ::= { prtT1E1CnfgTable 1}
prtT1E1CnfgEntry OBJECT-TYPE SYNTAX PrtT1E1CnfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " An entry in the T1/E1 port configuration table." INDEX { prtT1E1CnfgIdx, prtT1E1PrtIdx } ::= { prtT1E1CnfgTable 1}
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.164.3.3.3.2.2.1.1 | prtT1E1CnfgIdx | 0 | 0 | This attribute indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.2 | prtT1E1PrtIdx | 0 | 0 | This attribute indicates a unique port number. The same numbering as for prtGenPrtIdx. The valid port number depends on the IO s… |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.3 | prtT1E1Slt | 0 | 0 | This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this o… |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.4 | prtT1E1LineType | 0 | 0 | This variable indicates the variety of T1/E1 Line implementing this circuit. The type of circuit affects the number of bit… |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.5 | prtT1E1LineCode | 0 | 0 | This variable describes the variety of Zero Code Suppression used on the link, which in turn affects a number of its chara… |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.6 | prtT1E1SignalMode | 0 | 0 | 'none' indicates that no bits are reserved for signaling on this channel. 'robbedBit' indicates that T1 Robbed Bit Signaling is i… |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.7 | prtT1E1Fdl | 0 | 0 | This bitmap describes the use of the facili- ties data link, and is the sum of the capabili- ties: 'other' indicates that a prot… |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.8 | prtT1E1FdlMode | 0 | 0 | Fdl Mode of the T1 selected port. notApplicable - will be used for an E1 port. |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.9 | prtT1E1Sync | 0 | 0 | This object enables returning to normal operation, after the end of a main/sub link red alarm event, in reduced time. 'tr62411' -… |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.10 | prtT1E1CGA | 0 | 0 | This object selects the method used to signal the CGA state to the other end, through the main/sub link. 'none' - non-transparen… |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.11 | prtT1E1IdleCode | 0 | 0 | This object selects the code transmitted to fill idle (unused) time slots in the main link frame. Valid range: (0 - FF HEX) . |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.12 | prtT1E1OosSignal | 0 | 0 | 'idle' = '0' = on-hook, idle state 'busy' = '1' = off-hook, busy state 'forcedIdle' = SP = both A and B signaling bits are forced… |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.13 | prtT1E1VoiceOos | 0 | 0 | Voice Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0. |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.14 | prtT1E1DataOos | 0 | 0 | Data Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0. |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.15 | prtT1E1LineLengthMask | 0 | 0 | This attribute is the line length mask parameter used only for T1/DSU interfaces. len400p533ft=length range: 400ft to 533ft 'fcc68… |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.16 | prtT1E1TxGainMask | 0 | 0 | This attribute is the tx gain mask parameter (dB), used only for T1/CSU interfaces. |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.17 | prtT1E1InbandMng | 0 | 0 | A unique number to identify an Inband management over the link. internal - supported by KM-2100 only. It means that the managemen… |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.18 | prtT1E1InbandMngRate | 0 | 0 | A unique number to identify the rate of the Inband management. It is required only for E1 links and is applicable only when prtEx… |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.19 | prtT1E1DedicatedTs | 0 | 0 | The value is differently determined for different products. There are two methods: 1) A unique number to identify Dedicated TS of… |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.20 | prtT1E1InbandMngRoutProt | 0 | 0 | Inband Mng Routing Protocol of the port. When prtT1E1InbandMng is 'dedicatedPpp'-'proprietary' and 'rip2' are applicable. For othe… |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.21 | prtT1E1LinkMode | 0 | 0 | regular - TSs are connected by user via TS Assignment only transparent - when a port with this Link Mode is connected to an inter… |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.22 | prtT1E1Multiplier | 0 | 0 | The data rate of each TS. The multiplier values can be 56 kbps or 64 kbps. For T1 only. |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.23 | prtT1E1RxGain | 0 | 0 | This attribute is the rx volume (dB). |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.24 | prtT1E1RAI | 0 | 0 | Remote Alarm Signal |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.25 | prtT1E1LineMode | 0 | 0 | Interface type of the port. For T1 - csu, dsu are the valid values For E1 - dsu, ltu are the valid values |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.26 | prtT1E1TS0SaBits | 0 | 0 | This object is applicable only for E1 ports. For T1, string size will be 0. For E1, it enables user to select the use of TS0 Sa … |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.27 | prtT1E1ConnectedTS | 0 | 0 | This parameter indicates if there is any connected TS for this interface. |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.28 | prtT1E1Ts0SaBit | 0 | 0 | This parameter indicates whether to send TS 0, or not. noMng= TS 0 is looped, therefore not sent. mng= TS 0 isn't looped, therefo… |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.29 | prtT1E1SameFeCnfg | 0 | 0 | This parameter indicates whether the same E1 configuration parameters and TS assignment are set both to the local and remote devi… |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.30 | prtT1E1RemCrc4 | 0 | 0 | This object indicates whether the E1 of the Remote device connected to this E1 port, will have CRC-4 or not. |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.31 | prtT1E1MaxTSs | 0 | 0 | This object is applicable only for DXC D4T1, D4E1, D8T1, D8E1 external ports and D8GSL internal E1 ports. It is relevant only whe… |
| 1.3.6.1.4.1.164.3.3.3.2.2.1.32 | prtT1E1EocTsConfig | 0 | 0 | This object indicates whether the use of EOC for TS Configuration is enabled or not. |