This object determines the line impedance. This
is for the G.703 device only.
Parsed from file hot_msdsl.mib.txt
Company: paradyne
Module: HOTWIRE-MSDSL-INTERFACE-MIB
Child arc 0 is used to translate between SNMPv1 and SNMPv2 notification parameters as explained in IETF RFC 2576, section 3.
msdslConfigSystemLineTermination OBJECT-TYPE SYNTAX INTEGER { ohm120(1), ohm75(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This object determines the line impedance. This is for the G.703 device only." ::= { msdslConfiguration 6 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.6.0 | msdslConfigSystemLineTermination | 0 | 0 | None |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.1 | msdslNetworkTable | 1 | 11 | The MSDSL Network Interface Options table. |
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.2 | msdsldsx1Table | 1 | 4 | The MSDSL DSX-1 Interface Options table. |
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.3 | msdslG703Table | 1 | 4 | The MSDSL G.703 Interface Options table. |
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.4 | msdslSyncTable | 1 | 11 | The MSDSL Synchronous Data Port Interface Options table. |
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.5 | msdslConfigSystemDSLMode | 1 | 1 | This object is used to specify if the unit is configured as a network terminating unit (NTU), or as a line terminating (LTU) unit… |
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.7 | msdslConfigSystemTelcoLB | 1 | 1 | This object determines if the device will respond to Telco loopback signals on the DSX-1 interface. |
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.8 | msdslConfigSystemRemoteTelcoLB | 1 | 1 | This object determines if the unit will perform a Telco initiated line loopback on just the local unit (the one that detected the… |
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.9 | msdslConfigComPortType | 1 | 1 | This object is used when the communication port is configured as a network communication link and specifies whether the port will… |
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.10 | msdslConfigComIgnoreCntlLeads | 1 | 1 | This object is used to specify whether DTR is used. |
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.11 | msdslConfigComInactivityTO | 1 | 1 | This object is used to specify whether a user session should be disconnected (logged off) after a specified period of inactivity. |
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.12 | msdslConfigComDiscTime | 1 | 1 | This object is used to specify how long to wait before disconnecting. Inactivity is defined as no keyboard activity within a given… |
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.13 | msdslConfigTelnetSession | 1 | 1 | This object is used when the communication port is configured as a network communication link and specifies whether the port will… |
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.14 | msdslConfigTelnetLogin | 1 | 1 | This object is used to specify whether a user session should require a username and password. |
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.15 | msdslConfigTelnetAccessLevel | 1 | 1 | This object is used to specify the level of access privilages. |
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.16 | msdslConfigNodeIPaddr | 1 | 1 | This object is used to specify the IP address needed to access the node. Since this IP address is not bound to a particular port… |
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.17 | msdslConfigNodeSubnetMask | 1 | 1 | This object is used to specify the Subnet Mask needed to access the node. Since this Subnet Mask is not bound to a particular por… |
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.18 | msdslConfigDefaultNetDest | 1 | 1 | This object is used to specify the default network destination. This option allows the user to specify where the default network … |
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.19 | msdslConfigComIPaddr | 1 | 1 | This object is used to specify the IP address needed to access the unit when the communication port is configured as a network co… |
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.20 | msdslConfigComSubnetMask | 1 | 1 | This object is used to specify the Subnet Mask needed to access the unit when the communication port is configured as a network c… |
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.21 | msdslConfigLinkProtocol | 1 | 1 | This object is used to specify the link layer protocol to use when the communication port is configured as a network communicatio… |
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.22 | msdslConfigTrapDestination | 1 | 1 | This object is used to choose the destination of traps. NOTE: This is used by endpoints only |
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.23 | msdslConfigTrapLinkTrapInterface | 1 | 1 | This object is used to specify which interfaces will generate linkUp, linkDown, and enterpriseSpecific trap messages. These traps… |
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.24 | msdslDSLSWrevision | 1 | 1 | The Software revision for the GlobeSpan device in this entity. |
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.25 | msdslDSLHWrevision | 1 | 1 | The Hardware revision for the GlobeSpan device in this entity. |
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.26 | msdslDSLlineCode | 1 | 1 | The DSL line code type for this entity. |
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.27 | msdslLEDsTable | 1 | 3 | A list of the msdsl LED entries. |
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.28 | msdslFracTable | 1 | 6 | The Paradyne MSDSL Cross Connect Table. |
| 1.3.6.1.4.1.1795.2.24.2.6.15.1.15.29 | msdslPortConfigAllocMethodTable | 1 | 3 | The Paradyne MSDSL Cross Connect Allocation Method Table. |