This object allows selection of the transmit path analog signal
amplification on the specified voice port. The valid range depends of
the type of voice port. FXS and FXO ports accept -100 (-10.0 DB) to 50
(+5.0 DB) while E&M ports accept -170 (-17.0 DB) to 160 (+16.0 DB). The
increments must be in steps of 5 (0.5 DB). Specifying out of range
values or bad step sizes will result in BAD VALUE returns.
Parsed from file pdndce.mib.txt
Company: paradyne
Module: PDNDCE-MIB
Vendor: Paradyne
Module: PDNDCE-MIB (pdndce.mib)
Type: TABULAR
Access: read-write
Syntax: INTEGER
(
-170..80 )
Automatically extracted from www.mibdepot.com
devVoiceConfigTxAttenuation OBJECT-TYPE SYNTAX INTEGER (-170..80) ACCESS read-write STATUS mandatory DESCRIPTION "This object allows selection of the transmit path analog signal amplification on the specified voice port. The valid range depends of the type of voice port. FXS and FXO ports accept -100 (-10.0 DB) to 50 (+5.0 DB) while E&M ports accept -170 (-17.0 DB) to 160 (+16.0 DB). The increments must be in steps of 5 (0.5 DB). Specifying out of range values or bad step sizes will result in BAD VALUE returns." ::= { devVoiceConfigEntry 8 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.1795.2.24.2.6.4.1.1.1 | devVoiceConfigIfIndex | 0 | 0 | This object specifies which row, in the devVoiceConfigTable, to use for mib access. It's value is identical to IfIndex. |
| 1.3.6.1.4.1.1795.2.24.2.6.4.1.1.2 | devVoiceConfigPortStatus | 0 | 0 | This object is used to control the voice port state. The states supported are disable(1) and enable(2). Attempts to set any othe… |
| 1.3.6.1.4.1.1795.2.24.2.6.4.1.1.3 | devVoiceConfigOperatingMode | 0 | 0 | This object is used to select the desired operating mode for the specified voice port. The type of input depends of the type of … |
| 1.3.6.1.4.1.1795.2.24.2.6.4.1.1.4 | devVoiceConfigSignalingType | 0 | 0 | This object is used to select the desired signaling type for the specified voice port. The type of input depends of the type of … |
| 1.3.6.1.4.1.1795.2.24.2.6.4.1.1.5 | devVoiceConfigWinkDelay | 0 | 0 | This object provides a method for selecting the amount of delay before a Wink signal is sent to the network when an off-hook sig… |
| 1.3.6.1.4.1.1795.2.24.2.6.4.1.1.6 | devVoiceConfigWinkDuration | 0 | 0 | This object provides a method for selecting the duration of the Wink signal being sent to the network as a result of detecting a… |
| 1.3.6.1.4.1.1795.2.24.2.6.4.1.1.7 | devVoiceConfigRxgain | 0 | 0 | This object allows selection of the receive path analog signal amplification on the specified voice port. The valid range depend… |
| 1.3.6.1.4.1.1795.2.24.2.6.4.1.1.9 | devVoiceConfigRingBackTone | 0 | 0 | This object enables the generation of an audible tone, referred to as ring-back, towards the network in response to an incoming … |
| 1.3.6.1.4.1.1795.2.24.2.6.4.1.1.10 | devVoiceConfigTrunkCondInCGA | 0 | 0 | This object, Trunk Conditioning during Carrier Group Alarm, specifies what state the voice port assumes when the system enters a… |
| 1.3.6.1.4.1.1795.2.24.2.6.4.1.1.11 | devVoiceConfigTermImpedance | 0 | 0 | This object specifies the terminating impedance for the port. The default value is 600 ohms(z600). Attempting to set values othe… |