the status of the DS3/E3 line
Parsed from file ds3e3.mib.txt
Company: None
Module: Wellfleet-DS3E3-MIB
the status of the DS3/E3 line
Parsed from file Wellfleet-DS3E3-MIB.mib
Module: Wellfleet-DS3E3-MIB
Vendor: Wellfleet
Module: Wellfleet-DS3E3-MIB
[Automatically extracted from oidview.com]
wfDs3E3ConfigLineStatus OBJECT-TYPE SYNTAX INTEGER { noalarm(1), rcrai(2), txrai(4), rcais(8), txais(16), lof(32), los(64), loopback(128), rctestcode(256), otherfailure(512) } ACCESS read-only STATUS mandatory DESCRIPTION "the status of the DS3/E3 line" DEFVAL { noalarm } ::= { wfDs3E3ConfigEntry 10 }
wfDs3E3ConfigLineStatus OBJECT-TYPE SYNTAX INTEGER { noalarm(1), rcrai(2), txrai(4), rcais(8), txais(16), lof(32), los(64), loopback(128), rctestcode(256), otherfailure(512) } ACCESS read-only STATUS mandatory DESCRIPTION "the status of the DS3/E3 line" DEFVAL { noalarm } ::= { wfDs3E3ConfigEntry 10 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.18.3.4.26.10.1.1 | wfDs3E3ConfigDelete | 0 | 0 | Create/Delete parameter |
| 1.3.6.1.4.1.18.3.4.26.10.1.2 | wfDs3E3ConfigDisable | 0 | 0 | Enable/Disable parameter |
| 1.3.6.1.4.1.18.3.4.26.10.1.3 | wfDs3E3ConfigState | 0 | 0 | State of the DS3 Port. |
| 1.3.6.1.4.1.18.3.4.26.10.1.4 | wfDs3E3ConfigLastChange | 0 | 0 | The value of sysUpTime at the time the interface entered its current operational state. |
| 1.3.6.1.4.1.18.3.4.26.10.1.5 | wfDs3E3ConfigLineIndex | 0 | 0 | this corresponds to the Wellfleet circuit number |
| 1.3.6.1.4.1.18.3.4.26.10.1.6 | wfDs3E3ConfigIfIndex | 0 | 0 | this is value of ifIndex from the Interfaces table of MIB II (RFC 1213). |
| 1.3.6.1.4.1.18.3.4.26.10.1.7 | wfDs3E3ConfigLineType | 0 | 0 | the variety of DS3/E3 application implementing this circuit |
| 1.3.6.1.4.1.18.3.4.26.10.1.8 | wfDs3E3ConfigLineCoding | 0 | 0 | the variety of Zero Code Suppression used on the link |
| 1.3.6.1.4.1.18.3.4.26.10.1.9 | wfDs3E3ConfigLoopbackConfig | 0 | 0 | the loopback configuration of the DS3/E3 interface |
| 1.3.6.1.4.1.18.3.4.26.10.1.11 | wfDs3E3ConfigPrimaryClockSource | 0 | 0 | Selects the Primary source of the Tx Clock for the DS3/E3 interface |
| 1.3.6.1.4.1.18.3.4.26.10.1.12 | wfDs3E3ConfigSecondaryClockSource | 0 | 0 | Selects the Secondary source of the Tx Clock for the DS3/E3 interface |
| 1.3.6.1.4.1.18.3.4.26.10.1.13 | wfDs3E3ConfigMtu | 0 | 0 | MTU parameter for all channels on DS3 . |
| 1.3.6.1.4.1.18.3.4.26.10.1.14 | wfDs3E3ConfigLineBuildOut | 0 | 0 | Set according to cable length, short (less than 225 feet) or long (greater than 225 feet). |
| 1.3.6.1.4.1.18.3.4.26.10.1.15 | wfDs3E3ConfigCurrentClock | 0 | 0 | Indicates the clock source currently in use by the DS1 |
| 1.3.6.1.4.1.18.3.4.26.10.1.16 | wfDs3E3ConfigExtClockOperational | 0 | 0 | Indicates whether the External clock is operational |
| 1.3.6.1.4.1.18.3.4.26.10.1.17 | wfDs3E3ConfigSetupAlarmThreshold | 0 | 0 | Specifies setup time for performance failure conditions, in seconds. When a performance defect is present for greater than the ti… |
| 1.3.6.1.4.1.18.3.4.26.10.1.18 | wfDs3E3ConfigClearAlarmThreshold | 0 | 0 | Specifies clear time for performance failure conditions, in seconds. When a performance failure condition has been cleared for gr… |
| 1.3.6.1.4.1.18.3.4.26.10.1.19 | wfDs3E3ConfigLoopbackState | 0 | 0 | Indicates the current loopback state of this interface. The interface can be in one the following states: Line Loopback Payload Lo… |
| 1.3.6.1.4.1.18.3.4.26.10.1.20 | wfDs3E3ConfigSendCode | 0 | 0 | This variable is currently read-only and it indicates what type of code has been sent across the DS3 interface by the device. T… |