Indicates whether the External clock is operational
Parsed from file ds3e3.mib.txt
Company: None
Module: Wellfleet-DS3E3-MIB
Indicates whether the External clock is operational
Parsed from file Wellfleet-DS3E3-MIB.mib
Module: Wellfleet-DS3E3-MIB
Vendor: Wellfleet
Module: Wellfleet-DS3E3-MIB
[Automatically extracted from oidview.com]
wfDs3E3ConfigExtClockOperational OBJECT-TYPE SYNTAX INTEGER { present(1), notpresent(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether the External clock is operational" DEFVAL { notpresent } ::= { wfDs3E3ConfigEntry 16 }
wfDs3E3ConfigExtClockOperational OBJECT-TYPE SYNTAX INTEGER { present(1), notpresent(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether the External clock is operational" DEFVAL { notpresent } ::= { wfDs3E3ConfigEntry 16 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.18.3.4.26.10.1.1 | wfDs3E3ConfigDelete | 0 | 0 | Create/Delete parameter |
1.3.6.1.4.1.18.3.4.26.10.1.2 | wfDs3E3ConfigDisable | 0 | 0 | Enable/Disable parameter |
1.3.6.1.4.1.18.3.4.26.10.1.3 | wfDs3E3ConfigState | 0 | 0 | State of the DS3 Port. |
1.3.6.1.4.1.18.3.4.26.10.1.4 | wfDs3E3ConfigLastChange | 0 | 0 | The value of sysUpTime at the time the interface entered its current operational state. |
1.3.6.1.4.1.18.3.4.26.10.1.5 | wfDs3E3ConfigLineIndex | 0 | 0 | this corresponds to the Wellfleet circuit number |
1.3.6.1.4.1.18.3.4.26.10.1.6 | wfDs3E3ConfigIfIndex | 0 | 0 | this is value of ifIndex from the Interfaces table of MIB II (RFC 1213). |
1.3.6.1.4.1.18.3.4.26.10.1.7 | wfDs3E3ConfigLineType | 0 | 0 | the variety of DS3/E3 application implementing this circuit |
1.3.6.1.4.1.18.3.4.26.10.1.8 | wfDs3E3ConfigLineCoding | 0 | 0 | the variety of Zero Code Suppression used on the link |
1.3.6.1.4.1.18.3.4.26.10.1.9 | wfDs3E3ConfigLoopbackConfig | 0 | 0 | the loopback configuration of the DS3/E3 interface |
1.3.6.1.4.1.18.3.4.26.10.1.10 | wfDs3E3ConfigLineStatus | 0 | 0 | the status of the DS3/E3 line |
1.3.6.1.4.1.18.3.4.26.10.1.11 | wfDs3E3ConfigPrimaryClockSource | 0 | 0 | Selects the Primary source of the Tx Clock for the DS3/E3 interface |
1.3.6.1.4.1.18.3.4.26.10.1.12 | wfDs3E3ConfigSecondaryClockSource | 0 | 0 | Selects the Secondary source of the Tx Clock for the DS3/E3 interface |
1.3.6.1.4.1.18.3.4.26.10.1.13 | wfDs3E3ConfigMtu | 0 | 0 | MTU parameter for all channels on DS3 . |
1.3.6.1.4.1.18.3.4.26.10.1.14 | wfDs3E3ConfigLineBuildOut | 0 | 0 | Set according to cable length, short (less than 225 feet) or long (greater than 225 feet). |
1.3.6.1.4.1.18.3.4.26.10.1.15 | wfDs3E3ConfigCurrentClock | 0 | 0 | Indicates the clock source currently in use by the DS1 |
1.3.6.1.4.1.18.3.4.26.10.1.17 | wfDs3E3ConfigSetupAlarmThreshold | 0 | 0 | Specifies setup time for performance failure conditions, in seconds. When a performance defect is present for greater than the ti… |
1.3.6.1.4.1.18.3.4.26.10.1.18 | wfDs3E3ConfigClearAlarmThreshold | 0 | 0 | Specifies clear time for performance failure conditions, in seconds. When a performance failure condition has been cleared for gr… |
1.3.6.1.4.1.18.3.4.26.10.1.19 | wfDs3E3ConfigLoopbackState | 0 | 0 | Indicates the current loopback state of this interface. The interface can be in one the following states: Line Loopback Payload Lo… |
1.3.6.1.4.1.18.3.4.26.10.1.20 | wfDs3E3ConfigSendCode | 0 | 0 | This variable is currently read-only and it indicates what type of code has been sent across the DS3 interface by the device. T… |