breath of life parameter
Parsed from file sync.mib.txt
Company: None
Module: Wellfleet-SYNC-MIB
breath of life parameter
Parsed from file Wellfleet-SYNC-MIB.mib
Module: Wellfleet-SYNC-MIB
Vendor: Wellfleet
Module: Wellfleet-SYNC-MIB
[Automatically extracted from oidview.com]
wfSyncBofl OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "breath of life parameter" DEFVAL { enabled } ::= { wfSyncEntry 7 }
wfSyncBofl OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "breath of life parameter" DEFVAL { enabled } ::= { wfSyncEntry 7 }
To many brothers! Only 100 nearest brothers are shown.
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| ... | ||||
| 1.3.6.1.4.1.18.3.4.5.1.1 | wfSyncDelete | 0 | 0 | Create/Delete parameter |
| 1.3.6.1.4.1.18.3.4.5.1.2 | wfSyncDisable | 0 | 0 | Enable/Disable parameter |
| 1.3.6.1.4.1.18.3.4.5.1.3 | wfSyncState | 0 | 0 | Line Driver state variable, Reflects the current state of the Line Driver. NOTPRESENT is an obsoleted state. It is replaced wit… |
| 1.3.6.1.4.1.18.3.4.5.1.4 | wfSyncSlot | 0 | 0 | Instance ID Slot, filled in by driver |
| 1.3.6.1.4.1.18.3.4.5.1.5 | wfSyncConnector | 0 | 0 | Instance ID Connector, filled in by driver. For the ASN this attribute is an encoded value and is equal to 'module'*10 + 'connect… |
| 1.3.6.1.4.1.18.3.4.5.1.6 | wfSyncCct | 0 | 0 | CCT number for this line instance |
| 1.3.6.1.4.1.18.3.4.5.1.8 | wfSyncBoflTmo | 0 | 0 | breath of life timeout in seconds |
| 1.3.6.1.4.1.18.3.4.5.1.9 | wfSyncMtu | 0 | 0 | MTU parameter, this is buffer size for SYNC media, fixed |
| 1.3.6.1.4.1.18.3.4.5.1.10 | wfSyncMadr | 0 | 0 | Line MAC address, fixed - line driver fills in from the 48 bit address stored in the serial number prom for this connector. |
| 1.3.6.1.4.1.18.3.4.5.1.11 | wfSyncPromiscuous | 0 | 0 | The promiscuous parameter allows address filtering based on the local and remote addresses. When enabled, all frames are receiv… |
| 1.3.6.1.4.1.18.3.4.5.1.12 | wfSyncXid | 0 | 0 | XID enable/disable parameter. This parameter is used to enable or disable transmission/reception of Test XID frames. |
| 1.3.6.1.4.1.18.3.4.5.1.13 | wfSyncClkSource | 0 | 0 | Tx/Rx clock source is either internally or external generated. |
| 1.3.6.1.4.1.18.3.4.5.1.14 | wfSyncClkSpeed | 0 | 0 | Internal Tx/Rx clock speed. This speed selection is valid only when internal clocking is selected. |
| 1.3.6.1.4.1.18.3.4.5.1.15 | wfSyncSignalMode | 0 | 0 | The signal mode parameter indicates the line paramter balanced or unbalanced. |
| 1.3.6.1.4.1.18.3.4.5.1.16 | wfSyncRtsEnable | 0 | 0 | Note: In KG84 support, RTS has a different meaning |
| 1.3.6.1.4.1.18.3.4.5.1.17 | wfSyncBurstCount | 0 | 0 | Allows control over the DMA burst cycle duration on MK5025 based products. This attribute is ignored for AN and ASN products. T… |
| 1.3.6.1.4.1.18.3.4.5.1.18 | wfSyncService | 0 | 0 | Service type for this circuit. Transparent is raw HDLC mode, LLC1 will prefix the HDLC address and control fields to the frame. … |
| 1.3.6.1.4.1.18.3.4.5.1.19 | wfSyncRetryCount | 0 | 0 | The Retry count parameter indicates the number of retransmission attempts which will be tried per frame before a line is determi… |
| 1.3.6.1.4.1.18.3.4.5.1.20 | wfSyncLinkIdleTimer | 0 | 0 | The link idle parameter is the number of seconds before a line has been determined to be idle. An idle line is considered disco… |
| 1.3.6.1.4.1.18.3.4.5.1.21 | wfSyncRetryTimer | 0 | 0 | The Retry Timer parameter indicates the timeout in tenths of seconds for a response to be heard form the link. Link control fra… |
| 1.3.6.1.4.1.18.3.4.5.1.22 | wfSyncExtendedAddress | 0 | 0 | This parameter controls length determination of the address field. When this parameter is enabled, the first bit of the address … |
| 1.3.6.1.4.1.18.3.4.5.1.23 | wfSyncExtendedAddressForce | 0 | 0 | When this parameter is enabled, the receiver will assume that all address fields are 2 octets in length regardless of the first … |
| 1.3.6.1.4.1.18.3.4.5.1.24 | wfSyncExtendedControl | 0 | 0 | This parameter allows the control fields of all S and I frames to become 2 octets in length instead of one. Numbering of all I … |
| 1.3.6.1.4.1.18.3.4.5.1.25 | wfSyncExtendedControlForce | 0 | 0 | This parameter when enabled will force all control fields to become two octets in length regardless the first two bits in the co… |
| 1.3.6.1.4.1.18.3.4.5.1.26 | wfSyncConnectAttempts | 0 | 0 | This parameter controls the number of connection attempts which will be made during a LAPB connection request. This parameter is… |
| 1.3.6.1.4.1.18.3.4.5.1.27 | wfSyncWindowSizeTx | 0 | 0 | The window size parameter controls the number of I frames which may be transmitted without acknowledgement. Non EXTC mode. |
| 1.3.6.1.4.1.18.3.4.5.1.28 | wfSyncWindowSizeTxExtc | 0 | 0 | The window size parameter controls the number of I frames which may be transmitted without acknowledgement in EXTC mode. |
| 1.3.6.1.4.1.18.3.4.5.1.29 | wfSyncMinFrameSpace | 0 | 0 | The minimum frame spacing parameter defines the number of flags that are transmitted between adjacent frames. |
| 1.3.6.1.4.1.18.3.4.5.1.30 | wfSyncLocalAddress | 0 | 0 | The local address parameter contains the DTE,DCE or EXPLICIT value expressed as a single octet. It may be extended to 2 octets i… |
| 1.3.6.1.4.1.18.3.4.5.1.31 | wfSyncRemoteAddress | 0 | 0 | The remote address parameter contains the DTE,DCE or EXPLICIT value expressed as a single octet. It may be extended to 2 octets … |
| 1.3.6.1.4.1.18.3.4.5.1.32 | wfSyncPassThruLocalMadr | 0 | 0 | 48 bit MAC address of Local end of Sync Passthru circuit |
| 1.3.6.1.4.1.18.3.4.5.1.33 | wfSyncPassThruRemoteMadr | 0 | 0 | 48 bit MAC address of Remote end of Sync Passthru circuit |
| 1.3.6.1.4.1.18.3.4.5.1.34 | wfSyncWanProtocol | 0 | 0 | WAN protocol selection is provided via this parameter. The supported protocols can be selected per interface. |
| 1.3.6.1.4.1.18.3.4.5.1.35 | wfSyncCrcSize | 0 | 0 | CRC size parameter, 16 bit standard CCITT or extended 32 bit CRC |
| 1.3.6.1.4.1.18.3.4.5.1.36 | wfSyncRxOctets | 0 | 0 | Number of octets received without error |
| 1.3.6.1.4.1.18.3.4.5.1.37 | wfSyncRxFrames | 0 | 0 | Number of frames received without error |
| 1.3.6.1.4.1.18.3.4.5.1.38 | wfSyncTxOctets | 0 | 0 | Number of octets transmitted without error |
| 1.3.6.1.4.1.18.3.4.5.1.39 | wfSyncTxFrames | 0 | 0 | Number of frames transmitted without error |
| 1.3.6.1.4.1.18.3.4.5.1.40 | wfSyncRxErrors | 0 | 0 | Number of receive errors |
| 1.3.6.1.4.1.18.3.4.5.1.41 | wfSyncTxErrors | 0 | 0 | Number of transmission errors |
| 1.3.6.1.4.1.18.3.4.5.1.42 | wfSyncLackRescRx | 0 | 0 | Number of Rx frames dropped due to lack of buffer resources |
| 1.3.6.1.4.1.18.3.4.5.1.43 | wfSyncLackRescTx | 0 | 0 | Number of frames clipped in driver's transmit routine due to transmit congestion. |
| 1.3.6.1.4.1.18.3.4.5.1.44 | wfSyncUnderFlowTx | 0 | 0 | Number of transmission underflows, device FIFO went empty before next DMA request was granted. |
| 1.3.6.1.4.1.18.3.4.5.1.45 | wfSyncRejectsTx | 0 | 0 | For the mk50 driver: Number of reject frames which were transmitted For the quicsync driver: Not used For the quicsync driver in A… |
| 1.3.6.1.4.1.18.3.4.5.1.46 | wfSyncRejectsRx | 0 | 0 | For the mk50 driver: Number of reject frames which were received For the quicsync driver: Number of HDLC frames received with a no… |
| 1.3.6.1.4.1.18.3.4.5.1.47 | wfSyncOverFlowRx | 0 | 0 | Number of receive overflows, device FIFO overflowed before next DMA cycle granted. No buffer resources available. |
| 1.3.6.1.4.1.18.3.4.5.1.48 | wfSyncFramesIncompRx | 0 | 0 | Number of frames which were incompletely received. These are frames which may have resulted from FRMRR errors. |
| 1.3.6.1.4.1.18.3.4.5.1.49 | wfSyncBadFramesRx | 0 | 0 | Number of bad receive frames, caused by FCS errors or non octet aligned. |
| 1.3.6.1.4.1.18.3.4.5.1.50 | wfSyncFrameRejectsRx | 0 | 0 | Number of Frame Rejects received |
| 1.3.6.1.4.1.18.3.4.5.1.51 | wfSyncRuntsRx | 0 | 0 | Number of runt frames received or number of frames where the Carrier Detect signal was lost during reception. |
| 1.3.6.1.4.1.18.3.4.5.1.52 | wfSyncT1Timeouts | 0 | 0 | Number of T1 timeout's detected. The T1 timer is the link retransmission timer. Link control frames will be retransmitted when T… |
| 1.3.6.1.4.1.18.3.4.5.1.53 | wfSyncMemoryErrors | 0 | 0 | Number of memory access errors detected. A MERR is the expiration of a DMA cycle without the bus being granted within 26us. |
| 1.3.6.1.4.1.18.3.4.5.1.54 | wfSyncMediaType | 0 | 0 | Media type selection is provided via this parameter |
| 1.3.6.1.4.1.18.3.4.5.1.55 | wfSyncCfgTxQueueLength | 0 | 0 | Configured Transmit Queue Length. Values other than zero over-ride the router selected values. A value of zero has a special me… |
| 1.3.6.1.4.1.18.3.4.5.1.56 | wfSyncCfgRxQueueLength | 0 | 0 | Configured Receive Queue Length. Values other than zero over-ride the router selected values. A value of zero has a special mea… |
| 1.3.6.1.4.1.18.3.4.5.1.57 | wfSyncTxQueueLength | 0 | 0 | Current Transmit Queue Length. |
| ... | ||||