An entry in the SYNC table
Parsed from file sync.mib.txt
Company: None
Module: Wellfleet-SYNC-MIB
An entry in the SYNC table
Parsed from file Wellfleet-SYNC-MIB.mib
Module: Wellfleet-SYNC-MIB
Vendor: Wellfleet
Module: Wellfleet-SYNC-MIB
[Automatically extracted from oidview.com]
wfSyncEntry OBJECT-TYPE SYNTAX WfSyncEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the SYNC table" INDEX { wfSyncSlot, wfSyncConnector } ::= { wfSyncTable 1 }
wfSyncEntry OBJECT-TYPE SYNTAX WfSyncEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the SYNC table" INDEX { wfSyncSlot, wfSyncConnector } ::= { wfSyncTable 1 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.18.3.4.5.1.1 | wfSyncDelete | 0 | 0 | Create/Delete parameter |
| 1.3.6.1.4.1.18.3.4.5.1.2 | wfSyncDisable | 0 | 0 | Enable/Disable parameter |
| 1.3.6.1.4.1.18.3.4.5.1.3 | wfSyncState | 0 | 0 | Line Driver state variable, Reflects the current state of the Line Driver. NOTPRESENT is an obsoleted state. It is replaced wit… |
| 1.3.6.1.4.1.18.3.4.5.1.4 | wfSyncSlot | 0 | 0 | Instance ID Slot, filled in by driver |
| 1.3.6.1.4.1.18.3.4.5.1.5 | wfSyncConnector | 0 | 0 | Instance ID Connector, filled in by driver. For the ASN this attribute is an encoded value and is equal to 'module'*10 + 'connect… |
| 1.3.6.1.4.1.18.3.4.5.1.6 | wfSyncCct | 0 | 0 | CCT number for this line instance |
| 1.3.6.1.4.1.18.3.4.5.1.7 | wfSyncBofl | 0 | 0 | breath of life parameter |
| 1.3.6.1.4.1.18.3.4.5.1.8 | wfSyncBoflTmo | 0 | 0 | breath of life timeout in seconds |
| 1.3.6.1.4.1.18.3.4.5.1.9 | wfSyncMtu | 0 | 0 | MTU parameter, this is buffer size for SYNC media, fixed |
| 1.3.6.1.4.1.18.3.4.5.1.10 | wfSyncMadr | 0 | 0 | Line MAC address, fixed - line driver fills in from the 48 bit address stored in the serial number prom for this connector. |
| 1.3.6.1.4.1.18.3.4.5.1.11 | wfSyncPromiscuous | 0 | 0 | The promiscuous parameter allows address filtering based on the local and remote addresses. When enabled, all frames are receiv… |
| 1.3.6.1.4.1.18.3.4.5.1.12 | wfSyncXid | 0 | 0 | XID enable/disable parameter. This parameter is used to enable or disable transmission/reception of Test XID frames. |
| 1.3.6.1.4.1.18.3.4.5.1.13 | wfSyncClkSource | 0 | 0 | Tx/Rx clock source is either internally or external generated. |
| 1.3.6.1.4.1.18.3.4.5.1.14 | wfSyncClkSpeed | 0 | 0 | Internal Tx/Rx clock speed. This speed selection is valid only when internal clocking is selected. |
| 1.3.6.1.4.1.18.3.4.5.1.15 | wfSyncSignalMode | 0 | 0 | The signal mode parameter indicates the line paramter balanced or unbalanced. |
| 1.3.6.1.4.1.18.3.4.5.1.16 | wfSyncRtsEnable | 0 | 0 | Note: In KG84 support, RTS has a different meaning |
| 1.3.6.1.4.1.18.3.4.5.1.17 | wfSyncBurstCount | 0 | 0 | Allows control over the DMA burst cycle duration on MK5025 based products. This attribute is ignored for AN and ASN products. T… |
| 1.3.6.1.4.1.18.3.4.5.1.18 | wfSyncService | 0 | 0 | Service type for this circuit. Transparent is raw HDLC mode, LLC1 will prefix the HDLC address and control fields to the frame. … |
| 1.3.6.1.4.1.18.3.4.5.1.19 | wfSyncRetryCount | 0 | 0 | The Retry count parameter indicates the number of retransmission attempts which will be tried per frame before a line is determi… |
| 1.3.6.1.4.1.18.3.4.5.1.20 | wfSyncLinkIdleTimer | 0 | 0 | The link idle parameter is the number of seconds before a line has been determined to be idle. An idle line is considered disco… |
| 1.3.6.1.4.1.18.3.4.5.1.21 | wfSyncRetryTimer | 0 | 0 | The Retry Timer parameter indicates the timeout in tenths of seconds for a response to be heard form the link. Link control fra… |
| 1.3.6.1.4.1.18.3.4.5.1.22 | wfSyncExtendedAddress | 0 | 0 | This parameter controls length determination of the address field. When this parameter is enabled, the first bit of the address … |
| 1.3.6.1.4.1.18.3.4.5.1.23 | wfSyncExtendedAddressForce | 0 | 0 | When this parameter is enabled, the receiver will assume that all address fields are 2 octets in length regardless of the first … |
| 1.3.6.1.4.1.18.3.4.5.1.24 | wfSyncExtendedControl | 0 | 0 | This parameter allows the control fields of all S and I frames to become 2 octets in length instead of one. Numbering of all I … |
| 1.3.6.1.4.1.18.3.4.5.1.25 | wfSyncExtendedControlForce | 0 | 0 | This parameter when enabled will force all control fields to become two octets in length regardless the first two bits in the co… |
| 1.3.6.1.4.1.18.3.4.5.1.26 | wfSyncConnectAttempts | 0 | 0 | This parameter controls the number of connection attempts which will be made during a LAPB connection request. This parameter is… |
| 1.3.6.1.4.1.18.3.4.5.1.27 | wfSyncWindowSizeTx | 0 | 0 | The window size parameter controls the number of I frames which may be transmitted without acknowledgement. Non EXTC mode. |
| 1.3.6.1.4.1.18.3.4.5.1.28 | wfSyncWindowSizeTxExtc | 0 | 0 | The window size parameter controls the number of I frames which may be transmitted without acknowledgement in EXTC mode. |
| 1.3.6.1.4.1.18.3.4.5.1.29 | wfSyncMinFrameSpace | 0 | 0 | The minimum frame spacing parameter defines the number of flags that are transmitted between adjacent frames. |
| 1.3.6.1.4.1.18.3.4.5.1.30 | wfSyncLocalAddress | 0 | 0 | The local address parameter contains the DTE,DCE or EXPLICIT value expressed as a single octet. It may be extended to 2 octets i… |
| 1.3.6.1.4.1.18.3.4.5.1.31 | wfSyncRemoteAddress | 0 | 0 | The remote address parameter contains the DTE,DCE or EXPLICIT value expressed as a single octet. It may be extended to 2 octets … |
| 1.3.6.1.4.1.18.3.4.5.1.32 | wfSyncPassThruLocalMadr | 0 | 0 | 48 bit MAC address of Local end of Sync Passthru circuit |
| 1.3.6.1.4.1.18.3.4.5.1.33 | wfSyncPassThruRemoteMadr | 0 | 0 | 48 bit MAC address of Remote end of Sync Passthru circuit |
| 1.3.6.1.4.1.18.3.4.5.1.34 | wfSyncWanProtocol | 0 | 0 | WAN protocol selection is provided via this parameter. The supported protocols can be selected per interface. |
| 1.3.6.1.4.1.18.3.4.5.1.35 | wfSyncCrcSize | 0 | 0 | CRC size parameter, 16 bit standard CCITT or extended 32 bit CRC |
| 1.3.6.1.4.1.18.3.4.5.1.36 | wfSyncRxOctets | 0 | 0 | Number of octets received without error |
| 1.3.6.1.4.1.18.3.4.5.1.37 | wfSyncRxFrames | 0 | 0 | Number of frames received without error |
| 1.3.6.1.4.1.18.3.4.5.1.38 | wfSyncTxOctets | 0 | 0 | Number of octets transmitted without error |
| 1.3.6.1.4.1.18.3.4.5.1.39 | wfSyncTxFrames | 0 | 0 | Number of frames transmitted without error |
| 1.3.6.1.4.1.18.3.4.5.1.40 | wfSyncRxErrors | 0 | 0 | Number of receive errors |
| 1.3.6.1.4.1.18.3.4.5.1.41 | wfSyncTxErrors | 0 | 0 | Number of transmission errors |
| 1.3.6.1.4.1.18.3.4.5.1.42 | wfSyncLackRescRx | 0 | 0 | Number of Rx frames dropped due to lack of buffer resources |
| 1.3.6.1.4.1.18.3.4.5.1.43 | wfSyncLackRescTx | 0 | 0 | Number of frames clipped in driver's transmit routine due to transmit congestion. |
| 1.3.6.1.4.1.18.3.4.5.1.44 | wfSyncUnderFlowTx | 0 | 0 | Number of transmission underflows, device FIFO went empty before next DMA request was granted. |
| 1.3.6.1.4.1.18.3.4.5.1.45 | wfSyncRejectsTx | 0 | 0 | For the mk50 driver: Number of reject frames which were transmitted For the quicsync driver: Not used For the quicsync driver in A… |
| 1.3.6.1.4.1.18.3.4.5.1.46 | wfSyncRejectsRx | 0 | 0 | For the mk50 driver: Number of reject frames which were received For the quicsync driver: Number of HDLC frames received with a no… |
| 1.3.6.1.4.1.18.3.4.5.1.47 | wfSyncOverFlowRx | 0 | 0 | Number of receive overflows, device FIFO overflowed before next DMA cycle granted. No buffer resources available. |
| 1.3.6.1.4.1.18.3.4.5.1.48 | wfSyncFramesIncompRx | 0 | 0 | Number of frames which were incompletely received. These are frames which may have resulted from FRMRR errors. |
| 1.3.6.1.4.1.18.3.4.5.1.49 | wfSyncBadFramesRx | 0 | 0 | Number of bad receive frames, caused by FCS errors or non octet aligned. |
| 1.3.6.1.4.1.18.3.4.5.1.50 | wfSyncFrameRejectsRx | 0 | 0 | Number of Frame Rejects received |
| 1.3.6.1.4.1.18.3.4.5.1.51 | wfSyncRuntsRx | 0 | 0 | Number of runt frames received or number of frames where the Carrier Detect signal was lost during reception. |
| 1.3.6.1.4.1.18.3.4.5.1.52 | wfSyncT1Timeouts | 0 | 0 | Number of T1 timeout's detected. The T1 timer is the link retransmission timer. Link control frames will be retransmitted when T… |
| 1.3.6.1.4.1.18.3.4.5.1.53 | wfSyncMemoryErrors | 0 | 0 | Number of memory access errors detected. A MERR is the expiration of a DMA cycle without the bus being granted within 26us. |
| 1.3.6.1.4.1.18.3.4.5.1.54 | wfSyncMediaType | 0 | 0 | Media type selection is provided via this parameter |
| 1.3.6.1.4.1.18.3.4.5.1.55 | wfSyncCfgTxQueueLength | 0 | 0 | Configured Transmit Queue Length. Values other than zero over-ride the router selected values. A value of zero has a special me… |
| 1.3.6.1.4.1.18.3.4.5.1.56 | wfSyncCfgRxQueueLength | 0 | 0 | Configured Receive Queue Length. Values other than zero over-ride the router selected values. A value of zero has a special mea… |
| 1.3.6.1.4.1.18.3.4.5.1.57 | wfSyncTxQueueLength | 0 | 0 | Current Transmit Queue Length. |
| 1.3.6.1.4.1.18.3.4.5.1.58 | wfSyncRxQueueLength | 0 | 0 | Current Receive Queue Length. |
| 1.3.6.1.4.1.18.3.4.5.1.59 | wfSyncRxReplenMisses | 0 | 0 | Number of packet buffer misses while attempting to replenish driver receive ring. |
| 1.3.6.1.4.1.18.3.4.5.1.60 | wfSyncStartUpMode | 0 | 0 | Initiation of link level for LLC2 running LAPB |
| 1.3.6.1.4.1.18.3.4.5.1.61 | wfSyncIdleRRFrames | 0 | 0 | Transmit Link level RR's (Reciever Readys) during idle time. Every wfSyncLinkIdleTimer expiration an RR will be sent. |
| 1.3.6.1.4.1.18.3.4.5.1.62 | wfSyncMultilineMode | 0 | 0 | This indicates the roll the sync line plays in a Bandwidth on Demand multiline circuit. If this is not BOD, the mode is standard. |
| 1.3.6.1.4.1.18.3.4.5.1.63 | wfSyncBODExamPeriod | 0 | 0 | This indicates the interval that the line should be polled for possible congestion. This value is in tenths of a second |
| 1.3.6.1.4.1.18.3.4.5.1.64 | wfSyncBODFullThreshold | 0 | 0 | This is the percentage of the theoretical maximum line throughput that must be reached or exceeded before the line is considered … |
| 1.3.6.1.4.1.18.3.4.5.1.65 | wfSyncBODRecoverThreshold | 0 | 0 | This is the recovery threshold expressed as a percentage of the theoretical maximum line throughput. The actual throughput must… |
| 1.3.6.1.4.1.18.3.4.5.1.66 | wfSyncBODPeriodsToFail | 0 | 0 | This is the number of consecutive periods where the line throughput is above the congestion threshold required to declare the lin… |
| 1.3.6.1.4.1.18.3.4.5.1.67 | wfSyncKG84ACycle | 0 | 0 | Monitor sample time in milliseconds |
| 1.3.6.1.4.1.18.3.4.5.1.68 | wfSyncKG84ASyncLossInterval | 0 | 0 | timer starts when FCS error detected; if no good frame received during this time, declare loss of synchronization |
| 1.3.6.1.4.1.18.3.4.5.1.69 | wfSyncKG84ARemoteResyncWait | 0 | 0 | when loss of synchronization is detected, and CTS is low, start timer; if CTS is not high when timer expires, force sync request |
| 1.3.6.1.4.1.18.3.4.5.1.70 | wfSyncKG84ASyncPulse | 0 | 0 | interval to pulse KG84a SYNC signal, in milliseconds |
| 1.3.6.1.4.1.18.3.4.5.1.71 | wfSyncKG84AResyncs | 0 | 0 | number of KG84 resyncs performed |
| 1.3.6.1.4.1.18.3.4.5.1.72 | wfSyncKG84AResyncsDetected | 0 | 0 | number of KG84 resyncs detected |
| 1.3.6.1.4.1.18.3.4.5.1.73 | wfSyncKG84ABsu | 0 | 0 | value taken from mk5025 sync chip control block |
| 1.3.6.1.4.1.18.3.4.5.1.74 | wfSyncKG84AState | 0 | 0 | state of sync |
| 1.3.6.1.4.1.18.3.4.5.1.75 | wfSyncKG84AOkFrames | 0 | 0 | count of valid frames received. This value taken from normal sync processing, updated by timer routine when FCE error detected |
| 1.3.6.1.4.1.18.3.4.5.1.76 | wfSyncPollingEnable | 0 | 0 | Enable or Disable Sync Polling. When Sync Polling is enabled, the the Sync Driver will be disabled if the DSR lead is dropped. I… |
| 1.3.6.1.4.1.18.3.4.5.1.77 | wfSyncBackupPool | 0 | 0 | Backup pool id containing this line driver |
| 1.3.6.1.4.1.18.3.4.5.1.78 | wfSyncDemandPool | 0 | 0 | Dial on demand pool id containing this line driver |
| 1.3.6.1.4.1.18.3.4.5.1.79 | wfSyncLineNumber | 0 | 0 | line number for this line instance |
| 1.3.6.1.4.1.18.3.4.5.1.80 | wfSyncHoldDownTime | 0 | 0 | Wait this number of seconds before bringing the line up. This prevents line waffling if this is a reactivated primary line in a b… |
| 1.3.6.1.4.1.18.3.4.5.1.81 | wfSyncNetworkType | 0 | 0 | Specific Network Link Level to be executed, LAPB mode only. The types GOSIP and NET2 are used in conjunction with an MK5025 chip … |
| 1.3.6.1.4.1.18.3.4.5.1.82 | wfSyncActiveCct | 0 | 0 | Active CCT number for this line instance |
| 1.3.6.1.4.1.18.3.4.5.1.83 | wfSyncCableType | 0 | 0 | Type of Cable attached to the sync port - this is needed for V.25bis and Raise DTR to properly communicate with the modem |
| 1.3.6.1.4.1.18.3.4.5.1.84 | wfSyncRxDropPackets | 0 | 0 | Number of Rx packets dropped by driver. |
| 1.3.6.1.4.1.18.3.4.5.1.85 | wfSyncTxDropPackets | 0 | 0 | Number of Tx packets dropped by driver. |
| 1.3.6.1.4.1.18.3.4.5.1.86 | wfSyncModule | 0 | 0 | Module number for ASN platform, filled in by driver. For non-ASN platforms this attribute will not be used. |
| 1.3.6.1.4.1.18.3.4.5.1.87 | wfSyncActualConnector | 0 | 0 | Actual connector number for ASN platform, filled in by driver. For non-ASN platforms, this attribute will not be used. |
| 1.3.6.1.4.1.18.3.4.5.1.88 | wfSyncLineCoding | 0 | 0 | Line Coding for sync interface. Can be either NRZ or NRZI. |
| 1.3.6.1.4.1.18.3.4.5.1.89 | wfSyncLastChange | 0 | 0 | The value of SysUpTime at the time the interface entered it's current operational state (UP state). SysUpTime is defined as the… |
| 1.3.6.1.4.1.18.3.4.5.1.90 | wfSyncOutQLen | 0 | 0 | The instantaneous current length of the output packet queue (in packets). |
| 1.3.6.1.4.1.18.3.4.5.1.91 | wfSyncRemoteLpbkDetection | 0 | 0 | This attribute enables Remote Loopback Detection. When enabled along with wfSyncBofl, the device driver will detect when it is … |
| 1.3.6.1.4.1.18.3.4.5.1.92 | wfSyncLastState | 0 | 0 | The state which the driver was in prior to the most recent re-initialization. |
| 1.3.6.1.4.1.18.3.4.5.1.93 | wfSyncExternalClkSpeed | 0 | 0 | External Clock Speed. If external clocking is configured, this attribute should be set to the clock speed of the externally supp… |
| 1.3.6.1.4.1.18.3.4.5.1.94 | wfSyncBChannelOverride | 0 | 0 | For ISDN, indicates which B Channel we're using. By default, we'd like the B Channel tied to the connector defined in the instan… |
| 1.3.6.1.4.1.18.3.4.5.1.95 | wfSyncBChannel | 0 | 0 | Indicates which B Channel is running |
| 1.3.6.1.4.1.18.3.4.5.1.96 | wfSyncForceIFTF | 0 | 0 | Specifies the Inter Frame Time Fill (IFTF) pattern which gets transmitted when no data is being transmitted on a particular chan… |
| 1.3.6.1.4.1.18.3.4.5.1.97 | wfSyncPriority | 0 | 0 | Used by dial/switched services to assign priority of lines within the same demand or backup pool |
| 1.3.6.1.4.1.18.3.4.5.1.98 | wfSyncTurboBofl | 0 | 0 | DEBUG parameter - Turbo bofl enabled or disabled |
| 1.3.6.1.4.1.18.3.4.5.1.99 | wfSyncBoflNum | 0 | 0 | DEBUG parameter - Number of breath of life packets per breath of life |
| 1.3.6.1.4.1.18.3.4.5.1.100 | wfSyncBoflLen | 0 | 0 | DEBUG parameter - breath of life packet length |
| 1.3.6.1.4.1.18.3.4.5.1.101 | wfSyncTurboBoflMisses | 0 | 0 | DEBUG parameter - breath of life allocation failures |
| 1.3.6.1.4.1.18.3.4.5.1.102 | wfSyncTurboBoflInvocations | 0 | 0 | DEBUG parameter - breath of life invocations |
| 1.3.6.1.4.1.18.3.4.5.1.103 | wfSyncBandwidthOnDemandPool | 0 | 0 | Bandwidth pool id containing this line driver |
| 1.3.6.1.4.1.18.3.4.5.1.104 | wfSyncBODRecoverPeriodsToPass | 0 | 0 | This is the number of consecutive periods where the queue depth is below the congestion threshold required to declare the line co… |
| 1.3.6.1.4.1.18.3.4.5.1.105 | wfSyncBODHistory | 0 | 0 | DEBUG parameter - This is the SBOD history buffer. |
| 1.3.6.1.4.1.18.3.4.5.1.106 | wfSyncBODDebugFlag | 0 | 0 | DEBUG parameter - This is the SBOD Debug flag, used to control debug code for SBOD. |
| 1.3.6.1.4.1.18.3.4.5.1.107 | wfSyncBChRateAdaption | 0 | 0 | This attribute is only relevant when this Synchronous device driver is performing as an ISDN B channel over a BRI interface in l… |
| 1.3.6.1.4.1.18.3.4.5.1.108 | wfSyncBChActualRateAdaption | 0 | 0 | Indicates the current B Channel Rate Adaption in use. This attribute is only relevant when this Synchronous device driver is per… |
| 1.3.6.1.4.1.18.3.4.5.1.109 | wfSyncWanType | 0 | 0 | This attribute indicates whether this port should be configured as a SYNCHRONOUS or UART/ASYNCHRONOUS interface. |
| 1.3.6.1.4.1.18.3.4.5.1.110 | wfSyncAsyncBaudRate | 0 | 0 | Indicates the baud rate of the Tx/Rx character stream. This value should always be >= than speed at which the modems connect, but… |
| 1.3.6.1.4.1.18.3.4.5.1.111 | wfSyncCfgAsyncCmndMaxIdles | 0 | 0 | Maximum number of idles we'll receive (in Command Mode) between ASYNC frames. Values other than zero over-ride the router selecte… |
| 1.3.6.1.4.1.18.3.4.5.1.112 | wfSyncAsyncCmndMaxIdles | 0 | 0 | Maximum number of idles we'll receive (in Command Mode) (i.e. when the modems have not yet connected & entered data state), befor… |
| 1.3.6.1.4.1.18.3.4.5.1.113 | wfSyncCfgAsyncDataMaxIdles | 0 | 0 | Maximum number of idles we'll receive (in Data Mode) between ASYNC frames. Values other than zero over-ride the router selected v… |
| 1.3.6.1.4.1.18.3.4.5.1.114 | wfSyncAsyncDataMaxIdles | 0 | 0 | Maximum number of idles we'll receive (in Command Mode) (i.e. when the modems have connected & entered data state), before closin… |
| 1.3.6.1.4.1.18.3.4.5.1.115 | wfSyncFramesAbortTx | 0 | 0 | Number of frames where CTS was lost during transmission. |
| 1.3.6.1.4.1.18.3.4.5.1.116 | wfSyncPasyncParityType | 0 | 0 | Type of parity chosen for Polled Async |
| 1.3.6.1.4.1.18.3.4.5.1.117 | wfSyncPasyncCharacterLength | 0 | 0 | Number of data bits chosen for Polled Async |
| 1.3.6.1.4.1.18.3.4.5.1.118 | wfSyncPasyncStopLength | 0 | 0 | Number of stop bits chosen for Polled Async |
| 1.3.6.1.4.1.18.3.4.5.1.119 | wfSyncPasyncBaudRate | 0 | 0 | Indicates the baud rate of the Tx/Rx character stream. This value should always be >= than speed at which the modems connect, but… |
| 1.3.6.1.4.1.18.3.4.5.1.120 | wfSyncLocalConnectionState | 0 | 0 | The state of the cable at the router end. |
| 1.3.6.1.4.1.18.3.4.5.1.121 | wfSyncRemoteConnectionState | 0 | 0 | The state of the cable at the device end. |
| 1.3.6.1.4.1.18.3.4.5.1.122 | wfSyncTimeSlotAssignment | 0 | 0 | Lists the time-slots which constitute this channel. Read only attribute that contains a list of time-slots from 1 to 24 used by t… |
| 1.3.6.1.4.1.18.3.4.5.1.123 | wfSyncEiaStatus | 0 | 0 | The state of the EIA signals at the router interface. The signals are designated as bits in this entry. If the signal is asserted… |
| 1.3.6.1.4.1.18.3.4.5.1.124 | wfSyncEiaStatusReset | 0 | 0 | Reset The EIA status for the EIA signals in wfSyncEiaStatus. This is particularly useful for clearing the toggle status. |
| 1.3.6.1.4.1.18.3.4.5.1.125 | wfSyncUcastMap | 0 | 0 | Used to map ifEntry.ifInUcastPkts to wfSyncRxFrames and ifEntry.ifOutUcastPkts to wfSyncTxFrames. |
| 1.3.6.1.4.1.18.3.4.5.1.126 | wfSyncAsyncCfgMaxIdleTimer | 0 | 0 | Determines if Async Max Idle Timer should be based on the baudrate or on the time needed to receive three characters. |
| 1.3.6.1.4.1.18.3.4.5.1.127 | wfSyncPasyncMaxIdles | 0 | 0 | Maximum number of idles we'll receive between ASYNC frames. Values other than zero over-ride wfSyncAsyncCfgMaxIdleTimer. This att… |