Specifies a blue or yellow alarm to be transmitted
while in BERT mode.
Parsed from file WFMIB.asn.txt
Company: None
Module: Wellfleet-Series7-MIB
Specifies a blue or yellow alarm to be transmitted
while in BERT mode.
Parsed from file Wellfleet-MCT1-MIB.mib
Module: Wellfleet-MCT1-MIB
Vendor: Wellfleet
Module: Wellfleet-MCT1-MIB
[Automatically extracted from oidview.com]
wfMcT1BertSendAlarm OBJECT-TYPE SYNTAX INTEGER { blue(1), yellow(2), disabled(3) } ACCESS read-write STATUS mandatory DESCRIPTION " Specifies a blue or yellow alarm to be transmitted while in BERT mode. " DEFVAL { disabled } ::= { wfMcT1Entry 22 }
wfMcT1BertSendAlarm OBJECT-TYPE SYNTAX INTEGER { blue(1), yellow(2), disabled(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies a blue or yellow alarm to be transmitted while in BERT mode." DEFVAL { disabled } ::= { wfMcT1Entry 22 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.18.3.4.8.2.1.1 | wfMcT1Delete | 0 | 0 | Create/Delete parameter |
1.3.6.1.4.1.18.3.4.8.2.1.2 | wfMcT1Disable | 0 | 0 | Enable/Disable parameter |
1.3.6.1.4.1.18.3.4.8.2.1.3 | wfMcT1State | 0 | 0 | Line Driver state variable |
1.3.6.1.4.1.18.3.4.8.2.1.4 | wfMcT1Slot | 0 | 0 | Instance ID Slot, filled in by driver |
1.3.6.1.4.1.18.3.4.8.2.1.5 | wfMcT1Connector | 0 | 0 | Instance ID Connector, filled in by driver |
1.3.6.1.4.1.18.3.4.8.2.1.6 | wfMcT1OperationMode | 0 | 0 | An option to generate and analyze specific test patterns is provided in BERT mode of operation. Only one T1 port can be in BERT m… |
1.3.6.1.4.1.18.3.4.8.2.1.7 | wfMcT1Mtu | 0 | 0 | MTU parameter. Specifies the largest frame size that can be received by the MCT1 link module. Any received frame which is larger … |
1.3.6.1.4.1.18.3.4.8.2.1.8 | wfMcT1MunichVersion | 0 | 0 | Specifies version number of the MUNICH chip used |
1.3.6.1.4.1.18.3.4.8.2.1.9 | wfMcT1Dsx1LineType | 0 | 0 | Selects between the two framing formats supported - D4 and ESF. The sailent differences between the two formats are the number of… |
1.3.6.1.4.1.18.3.4.8.2.1.10 | wfMcT1Dsx1ZeroCoding | 0 | 0 | Selects between the two Zero Code Suppression formats used on the link. In B8ZS coding, any outgoing stream of eight consecutive … |
1.3.6.1.4.1.18.3.4.8.2.1.11 | wfMcT1Dsx1LoopbackConfig | 0 | 0 | Indicates the loopback configuration of the T1 interface. The interface can be in the following loopback states: Payload loopback… |
1.3.6.1.4.1.18.3.4.8.2.1.12 | wfMcT1Dsx1LineStatus | 0 | 0 | Indicates the line status of the T1 interface. It contains loopback state and alarm state information. The Dsx1LineStatus is a bi… |
1.3.6.1.4.1.18.3.4.8.2.1.13 | wfMcT1Dsx1SetupAlarmThreshold | 0 | 0 | Specifies setup time for performance failure conditions, in seconds. When a performance defect is present for greater than the ti… |
1.3.6.1.4.1.18.3.4.8.2.1.14 | wfMcT1Dsx1ClearAlarmThreshold | 0 | 0 | Specifies clear time for performance failure conditions, in seconds. When a performance failure condition has been cleared for gr… |
1.3.6.1.4.1.18.3.4.8.2.1.15 | wfMcT1Dsx1SignalLevel | 0 | 0 | Specifies T1 transmit power level, in terms of DB. They translate into cable length as follows: 0.0dB -> 0-133 ft 0.5dB -> 133-2… |
1.3.6.1.4.1.18.3.4.8.2.1.16 | wfMcT1LoopbackDisable | 0 | 0 | The MCT1 link module is capable of detecting loop up and loop down codes received from the far end. This parameter enables or dis… |
1.3.6.1.4.1.18.3.4.8.2.1.17 | wfMcT1Dsx1FDLOperationMode | 0 | 0 | Select between the two FDL modes of operation. The AT&T mode, 54016 is based on AT&T publication 54015-1989. The ANSI mode, T1403… |
1.3.6.1.4.1.18.3.4.8.2.1.18 | wfMcT1BertTxOutputLevel | 0 | 0 | Specifies T1 transmit power level, in terms of DB while the T1 port is in BERT mode. The power levels translate into cable length… |
1.3.6.1.4.1.18.3.4.8.2.1.19 | wfMcT1BertTestMode | 0 | 0 | Selects between the framing formats while in bert mode of operation. |
1.3.6.1.4.1.18.3.4.8.2.1.20 | wfMcT1BertLineCode | 0 | 0 | Selects between the two Zero Code Suppression formats used on the link while in BERT mode. In B8ZS coding, any outgoing stream of… |
1.3.6.1.4.1.18.3.4.8.2.1.21 | wfMcT1BertTestPattern | 0 | 0 | When a T1 port is in BERT mode, it is capable of generating a set of known patterns. This paramater selects between those patterns |
1.3.6.1.4.1.18.3.4.8.2.1.23 | wfMcT1DS2282Version | 0 | 0 | Specifies version number of DS2282 chip |
1.3.6.1.4.1.18.3.4.8.2.1.24 | wfMcT1Restart | 0 | 0 | Indicates Port gate should be restarted to read new configuration |
1.3.6.1.4.1.18.3.4.8.2.1.25 | wfMcT1Loopback | 0 | 0 | Selects line or payload loopback to be activated locally |
1.3.6.1.4.1.18.3.4.8.2.1.26 | wfMcT1FDLTargetAddress | 0 | 0 | Selects between the two FDL target address modes |