wfIpv6IftunnelProtocol
View at oid-info.com
If wfIpv6IfCircuit is zero, this
parameter specifies the tunnel protocol type:
ip4st - IPv6-in-IPv4 static tunnel,
ip6st - IPv6-in-Ipv6 static tunnel,
ip4au - IPv6-in-IPv4 automatic tunnel,
ip6au - IPv6-in-Ipv6 automatic tunnel,
ip4sa - IPv6-in-Ipv4 semiautomatic tunnel,
ip6sa - IPv6-in-Ipv6 semiautomatic tunnel.
Static tunnels are tunnels where both local and remote
endpoints must be defined. They are also called
configured tunnels.
Automatic tunnels are tunnels that don't have predefined
remote address, i.e. the destination address of
encapsulating header is derived from the destination
address of encapsulated packet. They also called
opened-end tunnels.
A semiautomatic tunnel acts as a static tunnel for outgoing
traffic and as an automatic (multipoint-to-point) tunnel
for incoming traffic. Both local and remote endpoints must
be configured.
Parsed from file ipv6.mib.txt
Company: None
Module: Wellfleet-IPV6-MIB
If wfIpv6IfCircuit is zero, this
parameter specifies the tunnel protocol type:
ip4st - IPv6-in-IPv4 static tunnel,
ip6st - IPv6-in-Ipv6 static tunnel,
ip4au - IPv6-in-IPv4 automatic tunnel,
ip6au - IPv6-in-Ipv6 automatic tunnel,
ip4sa - IPv6-in-Ipv4 semiautomatic tunnel,
ip6sa - IPv6-in-Ipv6 semiautomatic tunnel.
Static tunnels are tunnels where both local and remote
endpoints must be defined. They are also called
configured tunnels.
Automatic tunnels are tunnels that don't have predefined
remote address, i.e. the destination address of
encapsulating header is derived from the destination
address of encapsulated packet. They also called
opened-end tunnels.
A semiautomatic tunnel acts as a static tunnel for outgoing
traffic and as an automatic (multipoint-to-point) tunnel
for incoming traffic. Both local and remote endpoints must
be configured.
Parsed from file Wellfleet-IPV6-MIB.mib
Module: Wellfleet-IPV6-MIB
Vendor: Wellfleet
Module: Wellfleet-IPV6-MIB
[Automatically extracted from oidview.com]
wfIpv6IfTunnelProtocol OBJECT-TYPE SYNTAX INTEGER { ip4st(1), ip6st(2), ip4sa(3), ip6sa(4), ip4au(5), ip6au(6) } ACCESS read-write STATUS mandatory DESCRIPTION "If wfIpv6IfCircuit is zero, this parameter specifies the tunnel protocol type: ip4st - IPv6-in-IPv4 static tunnel, ip6st - IPv6-in-Ipv6 static tunnel, ip4au - IPv6-in-IPv4 automatic tunnel, ip6au - IPv6-in-Ipv6 automatic tunnel, ip4sa - IPv6-in-Ipv4 semiautomatic tunnel, ip6sa - IPv6-in-Ipv6 semiautomatic tunnel. Static tunnels are tunnels where both local and remote endpoints must be defined. They are also called configured tunnels. Automatic tunnels are tunnels that don't have predefined remote address, i.e. the destination address of encapsulating header is derived from the destination address of encapsulated packet. They also called opened-end tunnels. A semiautomatic tunnel acts as a static tunnel for outgoing traffic and as an automatic (multipoint-to-point) tunnel for incoming traffic. Both local and remote endpoints must be configured." DEFVAL { ip4st } ::= { wfIpv6IfEntry 26 }
wfIpv6IfTunnelProtocol OBJECT-TYPE SYNTAX INTEGER { ip4st(1), ip6st(2), ip4sa(3), ip6sa(4), ip4au(5), ip6au(6) } ACCESS read-write STATUS mandatory DESCRIPTION "If wfIpv6IfCircuit is zero, this parameter specifies the tunnel protocol type: ip4st - IPv6-in-IPv4 static tunnel, ip6st - IPv6-in-Ipv6 static tunnel, ip4au - IPv6-in-IPv4 automatic tunnel, ip6au - IPv6-in-Ipv6 automatic tunnel, ip4sa - IPv6-in-Ipv4 semiautomatic tunnel, ip6sa - IPv6-in-Ipv6 semiautomatic tunnel. Static tunnels are tunnels where both local and remote endpoints must be defined. They are also called configured tunnels. Automatic tunnels are tunnels that don't have predefined remote address, i.e. the destination address of encapsulating header is derived from the destination address of encapsulated packet. They also called opened-end tunnels. A semiautomatic tunnel acts as a static tunnel for outgoing traffic and as an automatic (multipoint-to-point) tunnel for incoming traffic. Both local and remote endpoints must be configured." DEFVAL { ip4st } ::= { wfIpv6IfEntry 26 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.1 | wfIpv6IfDelete | 0 | 0 | Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete an IPv6 inter… |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.2 | wfIpv6IfDisable | 0 | 0 | Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable an IPv6 int… |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.3 | wfIpv6IfState | 0 | 0 | The current operational state of the interface. Tokenless state indicates the no valid address token is assigned to the interface… |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.4 | wfIpv6IfIndex | 0 | 0 | A unique non-zero value for each interface. |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.5 | wfIpv6IfDescr | 0 | 0 | An optional textual string containing description of the interface. |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.6 | wfIpv6IfCircuit | 0 | 0 | The Circuit Number that this interface runs over. If Circuit Number is between 1 and 1023, it identifies a subnetwork/datalink la… |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.7 | wfIpv6IfCfgToken | 0 | 0 | The desired identifier (interface token) for this interface that is (at least) unique on the link this interface is attached to. … |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.8 | wfIpv6IfCfgTokenLength | 0 | 0 | The length of the configured interface token in bits. |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.9 | wfIpv6IfToken | 0 | 0 | wfIpv6Iftoken |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.10 | wfIpv6IfTokenLength | 0 | 0 | wfIpv6IftokenLength |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.11 | wfIpv6IfCfgPhysicalAddress | 0 | 0 | The desired link layer address set by the user |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.12 | wfIpv6IfPhysicalAddress | 0 | 0 | The Physical Address for this Interface - actual one used |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.13 | wfIpv6IfCfgLinkMTU | 0 | 0 | The configured link MTU. It will be only considered if it is less than the default MTU of the underlying media. A value of zero i… |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.14 | wfIpv6IfFwdCacheSize | 0 | 0 | Maximum number of entries allowed in the Forwarding (Cache) Table at one time. There is a forwarding table per interface. If thi… |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.15 | wfIpv6IfSlotMask | 0 | 0 | Slot mask for which slots a circuit-less interface is eligible to run on. The most significant bit represents slot 1, the next m… |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.16 | wfIpv6IfLastChange | 0 | 0 | The time (in hundredths of a second) since the node was last re-initialized at the time the interface entered its current operati… |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.17 | wfIpv6IfReasmMaxSize | 0 | 0 | The size of the largest IPv6 datagram which this entity can re-assemble from incoming IPv6 fragmented packets received on this in… |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.18 | wfIpv6IfMaxInfo | 0 | 0 | The maximum size of the INFO (non-MAC) field that this port will receive or transmit (effective MTU size). |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.19 | wfIpv6IfRedirect | 0 | 0 | Indicates whether we're sending out redirects on this Interface or not |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.20 | wfIpv6IfIcmpErrorLimit | 0 | 0 | The maximum number of ICMP Error messages that is allowed to be transmitted within 1 second interval out of this interface. |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.21 | wfIpv6IfTrEndStation | 0 | 0 | wfIpv6IftrEndStation |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.22 | wfIpv6IfSMDSGroupAddress | 0 | 0 | The SMDS group address |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.23 | wfIpv6IfFRBcastDlci | 0 | 0 | Frame Relay broadcast dlci |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.24 | wfIpv6IfFRMcast1Dlci | 0 | 0 | Frame Relay multicast dlci #1 |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.25 | wfIpv6IfFRMcast2Dlci | 0 | 0 | Frame Relay multicast dlci #2 |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.27 | wfIpv6IfIPv4TunnelLocalAddress | 0 | 0 | If wfIpv6IfCircuit is zero and the tunnel protocol type is IPv4 or ip4sa, this parameter contains the local IPv4 address of this … |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.28 | wfIpv6IfIPv4TunnelRemoteAddress | 0 | 0 | If wfIpv6IfCircuit is zero and the tunnel protocol type is IPv4 or ip4sa, this parameter contains the remote IPv4 address of this… |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.29 | wfIpv6IfIpv6TunnelIfIndex | 0 | 0 | If wfIpv6IfCircuit is zero and the tunnel protocol type is IPv6 or ip6sa, this parameter contains the IPv6 interface index of th… |
| 1.3.6.1.4.1.18.3.5.3.16.1.1.2.1.30 | wfIpv6IfIpv6TunnelRemoteAddress | 0 | 0 | If wfIpv6IfCircuit is zero and the tunnel protocol type is IPv6 or ip6sa, this parameter contains the remote IPv6 address of this… |