The parameters for a particular Data Link Connection Management Interface
Parsed from file fr2.mib.txt
Company: None
Module: Wellfleet-FR2-MIB
The parameters for a particular Data Link Connection Management Interface
Parsed from file Wellfleet-FR2-MIB.mib
Module: Wellfleet-FR2-MIB
Vendor: Wellfleet
Module: Wellfleet-FR2-MIB
[Automatically extracted from oidview.com]
wfFrIfDlcmiEntry OBJECT-TYPE SYNTAX WfFrIfDlcmiEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The parameters for a particular Data Link Connection Management Interface" INDEX { wfFrDlcmiLineNumber, wfFrDlcmiLLIndex } ::= { wfFrIfDlcmiTable 1 }
wfFrIfDlcmiEntry OBJECT-TYPE SYNTAX WfFrIfDlcmiEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The parameters for a particular Data Link Connection Management Interface" INDEX { wfFrDlcmiLineNumber, wfFrDlcmiLLIndex } ::= { wfFrIfDlcmiTable 1 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.18.3.5.9.9.1.1.1 | wfFrDlcmiDelete | 0 | 0 | Indication to delete this frame relay interface |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.2 | wfFrDlcmiDisable | 0 | 0 | Indicates when a dlcmi entry is to be enabled or disabled. |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.3 | wfFrDlcmiLineNumber | 0 | 0 | The line number on which this frame relay interface resides. This is the first of two instance identifiers. |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.4 | wfFrDlcmiLLIndex | 0 | 0 | The Lower layer index uniquely identifies the lower layer in cases where the lower layer may be something other than the physical… |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.5 | wfFrDlcmiCircuit | 0 | 0 | The circuit number of this entry |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.6 | wfFrDlcmiManagementType | 0 | 0 | This variable indicates which Data Link Connection Management scheme is active (and by implication, what DLCI it uses). |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.7 | wfFrDlcmiStatus | 0 | 0 | Indicates the state of the interface. It is called status because this is what it was called in the rfc. FR_STATUS_RUNNING is the… |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.8 | wfFrDlcmiAddress | 0 | 0 | This states which address format is in use on the FR interface. The default is Q922 |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.9 | wfFrDlcmiAddressLen | 0 | 0 | This variable states the address length in octets. In the case of Q922 format, the length indicates the entire length of the addr… |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.10 | wfFrDlcmiPollingInterval | 0 | 0 | The number of seconds between successive status enquiry messages |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.11 | wfFrDlcmiFullEnquiryInterval | 0 | 0 | The number of status enquiry intervals that pass before issuance of a full status enquiry message. |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.12 | wfFrDlcmiErrorThreshold | 0 | 0 | This is the maximum number of unanswered Status Enquiries the equipment shall accept before declaring the interface down. |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.13 | wfFrDlcmiMonitoredEvents | 0 | 0 | This is the number of status polling intervals over which the error threshold is counted. For example, if within 'MonitoredEvent… |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.14 | wfFrDlcmiMaxSupportedVCs | 0 | 0 | The maximum number of Virtual Circuits allowed for this interface. Usually dictated by the Frame Relay network. The system sets … |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.15 | wfFrDlcmiVCsConfigured | 0 | 0 | The number of VCs that are presently configured on the interface. |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.16 | wfFrDlcmiMulticast | 0 | 0 | This indicates whether the frame relay provider offers a multicast |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.17 | wfFrDlcmiSeqCount | 0 | 0 | This station's sequence counter. It represents the next value to send. |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.18 | wfFrDlcmiLastReceived | 0 | 0 | The sequence number just received from the switch. |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.19 | wfFrDlcmiPassiveSeqCount | 0 | 0 | This station's sequence counter for answering status enquiry. |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.20 | wfFrDlcmiPassiveReceived | 0 | 0 | The sequence number just received from the enquring station. |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.21 | wfFrDlcmiPolls | 0 | 0 | This is the counter of where we are in the polling cycle. |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.22 | wfFrDlcmiCongestionDisable | 0 | 0 | This indicates whether the VCs should use the congestion algorithm or not. Each VC may be configured to run the algorithm to ov… |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.23 | wfFrDlcmiCongestionTmr | 0 | 0 | This is the time period over which congestion notifications are counted. It is also the period during which the VC will cease se… |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.24 | wfFrDlcmiCongestionCtr | 0 | 0 | This represents the number of congestion notifications, when received within wfFrDlcmiCongestionTmr time, will result in the VC … |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.25 | wfFrErrType | 0 | 0 | Indicate the type of the last specific monitored error. |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.26 | wfFrErrData | 0 | 0 | Contains as much of the error packet as possible. |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.27 | wfFrErrTime | 0 | 0 | The time the last error occurred. |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.28 | wfFrErrDiscards | 0 | 0 | The number of inbound frames dropped because of format or other errors or because the VC was not known. |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.29 | wfFrErrDrops | 0 | 0 | The number of outbound frames dropped. Usually this is due the specified DLCI being unknown or a broadcast packet is too long |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.30 | wfFrErrFaults | 0 | 0 | The number of times that the Interface has come down due to errors since the system started. The value is reset when a restart p… |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.31 | wfFrErrFaultTime | 0 | 0 | The time at which the interface last went down. |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.32 | wfFrDlcmiDialFailureDisable | 0 | 0 | On a dial interface, this indicates whether to time-out if a full status message is not received. A timeout will cause the connec… |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.33 | wfFrDlcmiInterfaceType | 0 | 0 | Indicates the type of interface this is. A normal interface is not backed up, a primary interface is backed up, and a backup inte… |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.34 | wfFrDlcmiBackupFilterCct | 0 | 0 | The circuit number which defines the ppq filters that the backup interface will use. If 0, the filters defined for the default/ma… |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.35 | wfFrDlcmiDebugLevel | 0 | 0 | For Bay Networks internal use only. |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.36 | wfFrDlcmiTraceLevel | 0 | 0 | For Bay Networks internal use only. |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.37 | wfFrDlcmiCongestionMethod | 0 | 0 | Default congestion control method to use for all VCs on this interface. |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.38 | wfFrDlcmiShapingTmr | 0 | 0 | The interval, in ticks (1/1024th of a second), that VCs are processed for traffic shaping. |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.39 | wfFrDlcmiShapingHiQueueLimit | 0 | 0 | The total number of buffers that the interface will allow VCs to queue into the Hi queue. Divided by the number of traffic shaped… |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.40 | wfFrDlcmiShapingNormalQueueLimit | 0 | 0 | The total number of buffers that the interface will allow VCs to queue into the Normal queue. Divided by the number of traffic sh… |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.41 | wfFrDlcmiShapingLoQueueLimit | 0 | 0 | The total number of buffers that the interface will allow VCs to queue into the Lo queue. Divided by the number of traffic shaped… |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.42 | wfFrDlcmiXoffDisable | 0 | 0 | Indicates whether to listen(enabled) or ignore(disabled) XOFF (R-bit) notification |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.43 | wfFrDlcmiMissingPolls | 0 | 0 | Number of times there was no status enquiry response to a status enquiry |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.44 | wfFrDlcmiName | 0 | 0 | User name for this interface, used by BCC |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.45 | wfFrDlcmiEnableSinglePVCUpdate | 0 | 0 | Enables or disables the processing of Single Async PVC status messages that some switches use. If disabled, Single Async PVC sta… |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.46 | wfFrDlcmiAnnexSwEnq | 0 | 0 | Enables or disables the processing of status enquiry on annexdswitch(7) and annexaswitch(8). If it is enabled and the status enqu… |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.47 | wfFrDlcmiAnnexSwEnqTmr | 0 | 0 | Specify the timeout value in seconds for the status inquiry on annexdswitch(7) and annexaswitch(8). It is defaulted to 10 seconds. |
| 1.3.6.1.4.1.18.3.5.9.9.1.1.48 | wfFrDlcmiExtraStatusInfoEnable | 0 | 0 | Indicates whether or not to process extra lmi ies that may received from the switch |