Information describing the state information
displayed by a single sender's PATH message.
Parsed from file HUAWEI-RSVPTE-MIB.mib.txt
Company: huawei
Module: HUAWEI-RSVPTE-MIB
hwRsvpTeSenderEntry OBJECT-TYPE SYNTAX HwRsvpTeSenderEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information describing the state information displayed by a single sender's PATH message." INDEX { hwRsvpTeSessionNumber, hwRsvpTeSenderNumber } ::= { hwRsvpTeSenderTable 1 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.1 | hwRsvpTeSenderNumber | 0 | 0 | The number of this sender. This is for SNMP Indexing purposes only and has no relation to any protocol value. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.2 | hwRsvpTeSenderType | 0 | 0 | The type of session (IP4, IP6, IP6 with flow information, etc). |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.3 | hwRsvpTeSenderDestAddr | 0 | 0 | The destination address used by all senders in this session. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.4 | hwRsvpTeSenderAddr | 0 | 0 | The source address used by this sender in this session. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.5 | hwRsvpTeSenderDestAddrLength | 0 | 0 | The length of the destination address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 3… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.6 | hwRsvpTeSenderAddrLength | 0 | 0 | The length of the sender's address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 3… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.7 | hwRsvpTeSenderHopAddr | 0 | 0 | The address used by the previous RSVP hop (which may be the original sender). |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.8 | hwRsvpTeSenderHopLih | 0 | 0 | The Logical Interface Handle used by the pre- vious RSVP hop (which may be the original sender). |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.9 | hwRsvpTeSenderInterface | 0 | 0 | The ifIndex value of the interface on which this PATH message was most recently received. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.10 | hwRsvpTeSenderTSpecRate | 0 | 0 | The Average Bit Rate of the sender's data stream. Within a transmission burst, the ar- rival rate may be as fast as hwR… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.11 | hwRsvpTeSenderTSpecPeakRate | 0 | 0 | The Peak Bit Rate of the sender's data stream. Traffic arrival is not expected to exceed this rate at any time, apart from the… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.12 | hwRsvpTeSenderTSpecBurst | 0 | 0 | The size of the largest burst expected from the sender at a time. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.13 | hwRsvpTeSenderTSpecMinTu | 0 | 0 | The minimum message size for this flow. The policing algorithm will treat smaller messages as though they are this size. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.14 | hwRsvpTeSenderTSpecMaxTu | 0 | 0 | The maximum message size for this flow. The admission algorithm will reject TSpecs whose Maximum Transmission Unit, plus t… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.15 | hwRsvpTeSenderInterval | 0 | 0 | The interval between refresh messages as ad- vertised by the previous hop. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.16 | hwRsvpTeSenderRsvpHop | 0 | 0 | If TRUE, the node believes that the previous IP hop is an RSVP hop. If FALSE, the node be- lieves that the previous IP hop ma… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.17 | hwRsvpTeSenderPolicy | 0 | 0 | The contents of the policy object, displayed as an uninterpreted string of octets, including the object header. In the absence… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.18 | hwRsvpTeSenderAdspecBreak | 0 | 0 | The global break bit general characterization parameter from the ADSPEC. If TRUE, at least one non-IS hop was detected in th… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.19 | hwRsvpTeSenderAdspecHopCount | 0 | 0 | The hop count general characterization parame- ter from the ADSPEC. A return of zero or noSuchValue indicates one of the f… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.20 | hwRsvpTeSenderAdspecPathBw | 0 | 0 | The path bandwidth estimate general character- ization parameter from the ADSPEC. A return of zero or noSuchValue indicates one … |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.21 | hwRsvpTeSenderAdspecMinLatency | 0 | 0 | The minimum path latency general characteriza- tion parameter from the ADSPEC. A return of zero or noSuchValue indicates one … |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.22 | hwRsvpTeSenderAdspecMtu | 0 | 0 | The composed Maximum Transmission Unit general characterization parameter from the ADSPEC. A return of zero or noSuchValue indi… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.23 | hwRsvpTeSenderAdspecGuaranteedSvc | 0 | 0 | If TRUE, the ADSPEC contains a Guaranteed Ser- vice fragment. If FALSE, the ADSPEC does not contain a Guaranteed Service fragm… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.24 | hwRsvpTeSenderAdspecGuaranteedBreak | 0 | 0 | If TRUE, the Guaranteed Service fragment has its 'break' bit set, indicating that one or more nodes along the path do not … |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.25 | hwRsvpTeSenderAdspecGuaranteedCtot | 0 | 0 | If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the end-to-end composed value for the guaranteed service 'C' paramet… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.26 | hwRsvpTeSenderAdspecGuaranteedDtot | 0 | 0 | If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the end-to-end composed value for the guaranteed service 'D' paramet… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.27 | hwRsvpTeSenderAdspecGuaranteedCsum | 0 | 0 | If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the composed value for the guaranteed ser- vice 'C' parameter since the… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.28 | hwRsvpTeSenderAdspecGuaranteedDsum | 0 | 0 | If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the composed value for the guaranteed ser- vice 'D' parameter since the… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.29 | hwRsvpTeSenderAdspecGuaranteedHopCount | 0 | 0 | If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the hop count general characterization… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.30 | hwRsvpTeSenderAdspecGuaranteedPathBw | 0 | 0 | If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the path bandwidth estimate general … |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.31 | hwRsvpTeSenderAdspecGuaranteedMinLatency | 0 | 0 | If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the minimum path latency general character… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.32 | hwRsvpTeSenderAdspecGuaranteedMtu | 0 | 0 | If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the com- posed Maximum Transmission Uni… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.33 | hwRsvpTeSenderAdspecCtrlLoadSvc | 0 | 0 | If TRUE, the ADSPEC contains a Controlled Load Service fragment. If FALSE, the ADSPEC does not contain a Controlled Load S… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.34 | hwRsvpTeSenderAdspecCtrlLoadBreak | 0 | 0 | If TRUE, the Controlled Load Service fragment has its 'break' bit set, indicating that one or more nodes along the path do not … |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.35 | hwRsvpTeSenderAdspecCtrlLoadHopCount | 0 | 0 | If hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the hop count general characterization… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.36 | hwRsvpTeSenderAdspecCtrlLoadPathBw | 0 | 0 | If hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the path bandwidth estimate general … |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.37 | hwRsvpTeSenderAdspecCtrlLoadMinLatency | 0 | 0 | If hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the minimum path latency general character… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.38 | hwRsvpTeSenderAdspecCtrlLoadMtu | 0 | 0 | If hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the com- posed Maximum Transmission Uni… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.39 | hwRsvpTeSenderTtl | 0 | 0 | The TTL value in the RSVP header that was last received. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.40 | hwRsvpTeLspId | 0 | 0 | A 16-bit identifier used in the SENDER_TEMPLATE and the FILTER_SPEC that can be changed to allow a sender to share resources with… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.41 | hwRsvpTeSenderMsgIdSndFlag | 0 | 0 | Indicates that the message sender requests the peer to send an acknowledgment for the message. (0x01: ACK desired.) |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.42 | hwRsvpTeSenderMsgIdSndEpoch | 0 | 0 | A value that indicates when the Message_Identi- fier sequence has been reset. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.43 | hwRsvpTeSenderMsgIdSndNumber | 0 | 0 | When combined with the message generator's IP address, the Message_Identifier field uniquely identifies a message. The values pl… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.44 | hwRsvpTeSenderMsgIdRcvFlag | 0 | 0 | The message ID flag of the message latest received. It is used to identify whether ACK is desired or not. And it can be extended.… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.45 | hwRsvpTeSenderMsgIdRcvEpoch | 0 | 0 | The message ID epoch of the message latest received form the interface. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.46 | hwRsvpTeSenderMsgIdRcvNumber | 0 | 0 | The message ID number of the message latest received form the interface. A return of 0 indicates the absence of the MESSAGE_ID obj… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.47 | hwRsvpTeSenderClassType | 0 | 0 | Indicates the class-type. A return of zero indicates the absence of the object. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.48 | hwRsvpTeSenderLabelRequestCtype | 0 | 0 | The type of label request (without label range, with ATM label range, with frame relay label range, etc). |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.49 | hwRsvpTeSenderLabelRequestL3pid | 0 | 0 | An identifier of the layer 3 protocol using this path. Standard Ethertype values are used. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.50 | hwRsvpTeSenderLabelRequestAtmMinVpi | 0 | 0 | This 12 bit field specifies the lower bound of a block of Virtual Path Identifiers that is supported on the originating switch. … |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.51 | hwRsvpTeSenderLabelRequestAtmMinVci | 0 | 0 | This 16 bit field specifies the lower bound of a block of Virtual Connection Identifiers that is supported on the originating swi… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.52 | hwRsvpTeSenderLabelRequestAtmMaxVpi | 0 | 0 | This 12 bit field specifies the upper bound of a block of Virtual Path Identifiers that is supported on the originating switch. … |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.53 | hwRsvpTeSenderLabelRequestAtmMaxVci | 0 | 0 | This 16 bit field specifies the upper bound of a block of Virtual Connection Identifiers that is supported on the originating swi… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.54 | hwRsvpTeSenderLabelRequestFrMinDlci | 0 | 0 | This 23-bit field specifies the lower bound of a block of Data Link Connection Identifiers (DLCIs) that is supported on the origi… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.55 | hwRsvpTeSenderLabelRequestFrMaxDlci | 0 | 0 | This 23-bit field specifies the upper bound of a block of Data Link Connection Identifiers (DLCIs) that is supported on the origi… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.56 | hwRsvpTeSenderSessionAttrType | 0 | 0 | The type of the session_attribute (without resource affinities or with resource affinities). |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.57 | hwRsvpTeSenderSessionAttrSetupPrio | 0 | 0 | The priority of the session with respect to taking resources, in the range of 0 to 7. The value 0 is the highest priority. The S… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.58 | hwRsvpTeSenderSessionAttrHoldPrio | 0 | 0 | The priority of the session with respect to holding resources, in the range of 0 to 7. The value 0 is the highest priority. Hold… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.59 | hwRsvpTeSenderSessionAttrFlag | 0 | 0 | A mixed value. (0x01: Local protection desired; 0x02: Label recording desired; 0x04: SE Style desired; 0x08: bandwidth protection… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.60 | hwRsvpTeSenderSessionAttrName | 0 | 0 | Session name, a null padded string of characters. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.61 | hwRsvpTeSenderSessionAttrExcludeAny | 0 | 0 | A 32-bit vector representing a set of attribute filters associated with a tunnel any of which renders a link unacceptable. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.62 | hwRsvpTeSenderSessionAttrIncludeAny | 0 | 0 | A 32-bit vector representing a set of attribute filters associated with a tunnel any of which renders a link acceptable (with res… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.63 | hwRsvpTeSenderSessionAttrIncludeAll | 0 | 0 | A 32-bit vector representing a set of attribute filters associated with a tunnel all of which must be present for a link to be ac… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.64 | hwRsvpTeSenderFrrSetupPrio | 0 | 0 | The priority of the backup path with respect to taking resources, in the range 0 to 7. The value 0 is the highest priority. Set… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.65 | hwRsvpTeSenderFrrHoldPrio | 0 | 0 | The priority of the backup path with respect to holding resources, in the range 0 to 7. The value 0 is the highest priority. Ho… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.66 | hwRsvpTeSenderFrrHopLimit | 0 | 0 | The maximum number of extra hops the backup path is allowed to take, from current node (a PLR) to an MP, with PLR and MP excluded… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.67 | hwRsvpTeSenderFrrFlag | 0 | 0 | An enumerable value to indicate the protection schema desired (0x01, One-to-One Backup Desired; 0x02, Facility Backup Desired; 0x… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.68 | hwRsvpTeSenderFrrBandwidth | 0 | 0 | Bandwidth estimate; 32-bit IEEE floating point integer, in bits per second. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.69 | hwRsvpTeSenderFrrExcludeAny | 0 | 0 | A 32-bit vector representing a set of attribute filters associated with a backup path, any of which renders a link unacceptable. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.70 | hwRsvpTeSenderFrrIncludeAny | 0 | 0 | A 32-bit vector representing a set of attribute filters associated with a backup path, any of which renders a link acceptable (wi… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.71 | hwRsvpTeSenderFrrIncludeAll | 0 | 0 | A 32-bit vector representing a set of attribute filters associated with a backup path, all of which must be present for a link to… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.72 | hwRsvpTeSenderFrrInuseFlag | 0 | 0 | An enumerable value to indicate the fast-reroute state of this sender (normal, PLR in use, MP in use, PLR in use and MP in use, u… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.73 | hwRsvpTeSenderDiffServPsc | 0 | 0 | This 16 bits field indicates a PHB Scheduling Class to be supported by the LSP. |