This 23-bit field specifies the upper bound of
a block of Data Link Connection Identifiers
(DLCIs) that is supported on the originating
switch. The DLCI must be right justified in
this field and unused bits must be set to 0.
Parsed from file HUAWEI-RSVPTE-MIB.mib.txt
Company: huawei
Module: HUAWEI-RSVPTE-MIB
hwRsvpTeSenderLabelRequestFrMaxDlci OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This 23-bit field specifies the upper bound of a block of Data Link Connection Identifiers (DLCIs) that is supported on the originating switch. The DLCI must be right justified in this field and unused bits must be set to 0." ::= { hwRsvpTeSenderEntry 55 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.1 | hwRsvpTeSenderNumber | 0 | 0 | The number of this sender. This is for SNMP Indexing purposes only and has no relation to any protocol value. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.2 | hwRsvpTeSenderType | 0 | 0 | The type of session (IP4, IP6, IP6 with flow information, etc). |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.3 | hwRsvpTeSenderDestAddr | 0 | 0 | The destination address used by all senders in this session. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.4 | hwRsvpTeSenderAddr | 0 | 0 | The source address used by this sender in this session. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.5 | hwRsvpTeSenderDestAddrLength | 0 | 0 | The length of the destination address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 3… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.6 | hwRsvpTeSenderAddrLength | 0 | 0 | The length of the sender's address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 3… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.7 | hwRsvpTeSenderHopAddr | 0 | 0 | The address used by the previous RSVP hop (which may be the original sender). |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.8 | hwRsvpTeSenderHopLih | 0 | 0 | The Logical Interface Handle used by the pre- vious RSVP hop (which may be the original sender). |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.9 | hwRsvpTeSenderInterface | 0 | 0 | The ifIndex value of the interface on which this PATH message was most recently received. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.10 | hwRsvpTeSenderTSpecRate | 0 | 0 | The Average Bit Rate of the sender's data stream. Within a transmission burst, the ar- rival rate may be as fast as hwR… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.11 | hwRsvpTeSenderTSpecPeakRate | 0 | 0 | The Peak Bit Rate of the sender's data stream. Traffic arrival is not expected to exceed this rate at any time, apart from the… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.12 | hwRsvpTeSenderTSpecBurst | 0 | 0 | The size of the largest burst expected from the sender at a time. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.13 | hwRsvpTeSenderTSpecMinTu | 0 | 0 | The minimum message size for this flow. The policing algorithm will treat smaller messages as though they are this size. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.14 | hwRsvpTeSenderTSpecMaxTu | 0 | 0 | The maximum message size for this flow. The admission algorithm will reject TSpecs whose Maximum Transmission Unit, plus t… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.15 | hwRsvpTeSenderInterval | 0 | 0 | The interval between refresh messages as ad- vertised by the previous hop. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.16 | hwRsvpTeSenderRsvpHop | 0 | 0 | If TRUE, the node believes that the previous IP hop is an RSVP hop. If FALSE, the node be- lieves that the previous IP hop ma… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.17 | hwRsvpTeSenderPolicy | 0 | 0 | The contents of the policy object, displayed as an uninterpreted string of octets, including the object header. In the absence… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.18 | hwRsvpTeSenderAdspecBreak | 0 | 0 | The global break bit general characterization parameter from the ADSPEC. If TRUE, at least one non-IS hop was detected in th… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.19 | hwRsvpTeSenderAdspecHopCount | 0 | 0 | The hop count general characterization parame- ter from the ADSPEC. A return of zero or noSuchValue indicates one of the f… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.20 | hwRsvpTeSenderAdspecPathBw | 0 | 0 | The path bandwidth estimate general character- ization parameter from the ADSPEC. A return of zero or noSuchValue indicates one … |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.21 | hwRsvpTeSenderAdspecMinLatency | 0 | 0 | The minimum path latency general characteriza- tion parameter from the ADSPEC. A return of zero or noSuchValue indicates one … |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.22 | hwRsvpTeSenderAdspecMtu | 0 | 0 | The composed Maximum Transmission Unit general characterization parameter from the ADSPEC. A return of zero or noSuchValue indi… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.23 | hwRsvpTeSenderAdspecGuaranteedSvc | 0 | 0 | If TRUE, the ADSPEC contains a Guaranteed Ser- vice fragment. If FALSE, the ADSPEC does not contain a Guaranteed Service fragm… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.24 | hwRsvpTeSenderAdspecGuaranteedBreak | 0 | 0 | If TRUE, the Guaranteed Service fragment has its 'break' bit set, indicating that one or more nodes along the path do not … |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.25 | hwRsvpTeSenderAdspecGuaranteedCtot | 0 | 0 | If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the end-to-end composed value for the guaranteed service 'C' paramet… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.26 | hwRsvpTeSenderAdspecGuaranteedDtot | 0 | 0 | If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the end-to-end composed value for the guaranteed service 'D' paramet… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.27 | hwRsvpTeSenderAdspecGuaranteedCsum | 0 | 0 | If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the composed value for the guaranteed ser- vice 'C' parameter since the… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.28 | hwRsvpTeSenderAdspecGuaranteedDsum | 0 | 0 | If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the composed value for the guaranteed ser- vice 'D' parameter since the… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.29 | hwRsvpTeSenderAdspecGuaranteedHopCount | 0 | 0 | If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the hop count general characterization… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.30 | hwRsvpTeSenderAdspecGuaranteedPathBw | 0 | 0 | If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the path bandwidth estimate general … |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.31 | hwRsvpTeSenderAdspecGuaranteedMinLatency | 0 | 0 | If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the minimum path latency general character… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.32 | hwRsvpTeSenderAdspecGuaranteedMtu | 0 | 0 | If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the com- posed Maximum Transmission Uni… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.33 | hwRsvpTeSenderAdspecCtrlLoadSvc | 0 | 0 | If TRUE, the ADSPEC contains a Controlled Load Service fragment. If FALSE, the ADSPEC does not contain a Controlled Load S… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.34 | hwRsvpTeSenderAdspecCtrlLoadBreak | 0 | 0 | If TRUE, the Controlled Load Service fragment has its 'break' bit set, indicating that one or more nodes along the path do not … |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.35 | hwRsvpTeSenderAdspecCtrlLoadHopCount | 0 | 0 | If hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the hop count general characterization… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.36 | hwRsvpTeSenderAdspecCtrlLoadPathBw | 0 | 0 | If hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the path bandwidth estimate general … |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.37 | hwRsvpTeSenderAdspecCtrlLoadMinLatency | 0 | 0 | If hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the minimum path latency general character… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.38 | hwRsvpTeSenderAdspecCtrlLoadMtu | 0 | 0 | If hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the com- posed Maximum Transmission Uni… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.39 | hwRsvpTeSenderTtl | 0 | 0 | The TTL value in the RSVP header that was last received. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.40 | hwRsvpTeLspId | 0 | 0 | A 16-bit identifier used in the SENDER_TEMPLATE and the FILTER_SPEC that can be changed to allow a sender to share resources with… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.41 | hwRsvpTeSenderMsgIdSndFlag | 0 | 0 | Indicates that the message sender requests the peer to send an acknowledgment for the message. (0x01: ACK desired.) |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.42 | hwRsvpTeSenderMsgIdSndEpoch | 0 | 0 | A value that indicates when the Message_Identi- fier sequence has been reset. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.43 | hwRsvpTeSenderMsgIdSndNumber | 0 | 0 | When combined with the message generator's IP address, the Message_Identifier field uniquely identifies a message. The values pl… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.44 | hwRsvpTeSenderMsgIdRcvFlag | 0 | 0 | The message ID flag of the message latest received. It is used to identify whether ACK is desired or not. And it can be extended.… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.45 | hwRsvpTeSenderMsgIdRcvEpoch | 0 | 0 | The message ID epoch of the message latest received form the interface. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.46 | hwRsvpTeSenderMsgIdRcvNumber | 0 | 0 | The message ID number of the message latest received form the interface. A return of 0 indicates the absence of the MESSAGE_ID obj… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.47 | hwRsvpTeSenderClassType | 0 | 0 | Indicates the class-type. A return of zero indicates the absence of the object. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.48 | hwRsvpTeSenderLabelRequestCtype | 0 | 0 | The type of label request (without label range, with ATM label range, with frame relay label range, etc). |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.49 | hwRsvpTeSenderLabelRequestL3pid | 0 | 0 | An identifier of the layer 3 protocol using this path. Standard Ethertype values are used. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.50 | hwRsvpTeSenderLabelRequestAtmMinVpi | 0 | 0 | This 12 bit field specifies the lower bound of a block of Virtual Path Identifiers that is supported on the originating switch. … |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.51 | hwRsvpTeSenderLabelRequestAtmMinVci | 0 | 0 | This 16 bit field specifies the lower bound of a block of Virtual Connection Identifiers that is supported on the originating swi… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.52 | hwRsvpTeSenderLabelRequestAtmMaxVpi | 0 | 0 | This 12 bit field specifies the upper bound of a block of Virtual Path Identifiers that is supported on the originating switch. … |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.53 | hwRsvpTeSenderLabelRequestAtmMaxVci | 0 | 0 | This 16 bit field specifies the upper bound of a block of Virtual Connection Identifiers that is supported on the originating swi… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.54 | hwRsvpTeSenderLabelRequestFrMinDlci | 0 | 0 | This 23-bit field specifies the lower bound of a block of Data Link Connection Identifiers (DLCIs) that is supported on the origi… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.56 | hwRsvpTeSenderSessionAttrType | 0 | 0 | The type of the session_attribute (without resource affinities or with resource affinities). |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.57 | hwRsvpTeSenderSessionAttrSetupPrio | 0 | 0 | The priority of the session with respect to taking resources, in the range of 0 to 7. The value 0 is the highest priority. The S… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.58 | hwRsvpTeSenderSessionAttrHoldPrio | 0 | 0 | The priority of the session with respect to holding resources, in the range of 0 to 7. The value 0 is the highest priority. Hold… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.59 | hwRsvpTeSenderSessionAttrFlag | 0 | 0 | A mixed value. (0x01: Local protection desired; 0x02: Label recording desired; 0x04: SE Style desired; 0x08: bandwidth protection… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.60 | hwRsvpTeSenderSessionAttrName | 0 | 0 | Session name, a null padded string of characters. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.61 | hwRsvpTeSenderSessionAttrExcludeAny | 0 | 0 | A 32-bit vector representing a set of attribute filters associated with a tunnel any of which renders a link unacceptable. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.62 | hwRsvpTeSenderSessionAttrIncludeAny | 0 | 0 | A 32-bit vector representing a set of attribute filters associated with a tunnel any of which renders a link acceptable (with res… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.63 | hwRsvpTeSenderSessionAttrIncludeAll | 0 | 0 | A 32-bit vector representing a set of attribute filters associated with a tunnel all of which must be present for a link to be ac… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.64 | hwRsvpTeSenderFrrSetupPrio | 0 | 0 | The priority of the backup path with respect to taking resources, in the range 0 to 7. The value 0 is the highest priority. Set… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.65 | hwRsvpTeSenderFrrHoldPrio | 0 | 0 | The priority of the backup path with respect to holding resources, in the range 0 to 7. The value 0 is the highest priority. Ho… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.66 | hwRsvpTeSenderFrrHopLimit | 0 | 0 | The maximum number of extra hops the backup path is allowed to take, from current node (a PLR) to an MP, with PLR and MP excluded… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.67 | hwRsvpTeSenderFrrFlag | 0 | 0 | An enumerable value to indicate the protection schema desired (0x01, One-to-One Backup Desired; 0x02, Facility Backup Desired; 0x… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.68 | hwRsvpTeSenderFrrBandwidth | 0 | 0 | Bandwidth estimate; 32-bit IEEE floating point integer, in bits per second. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.69 | hwRsvpTeSenderFrrExcludeAny | 0 | 0 | A 32-bit vector representing a set of attribute filters associated with a backup path, any of which renders a link unacceptable. |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.70 | hwRsvpTeSenderFrrIncludeAny | 0 | 0 | A 32-bit vector representing a set of attribute filters associated with a backup path, any of which renders a link acceptable (wi… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.71 | hwRsvpTeSenderFrrIncludeAll | 0 | 0 | A 32-bit vector representing a set of attribute filters associated with a backup path, all of which must be present for a link to… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.72 | hwRsvpTeSenderFrrInuseFlag | 0 | 0 | An enumerable value to indicate the fast-reroute state of this sender (normal, PLR in use, MP in use, PLR in use and MP in use, u… |
| 1.3.6.1.4.1.2011.5.25.148.1.2.1.73 | hwRsvpTeSenderDiffServPsc | 0 | 0 | This 16 bits field indicates a PHB Scheduling Class to be supported by the LSP. |