Vendor: Fujitsu Siemens Computers
Module: XLDV20-MIB
[Automatically extracted from oidview.com]
xldv20AtmCcControl OBJECT IDENTIFIER ::= { xldv20CallP 1 }
xldv20AtmCcControl OBJECT IDENTIFIER ::= { xldv20CallP 1 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.1 | xldv20ActOperationalState | 1 | 1 | Unused. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.2 | xldv20ActControlReq | 1 | 1 | COH (Connection Handling) user commands. Notifications : xldv20TrStateChangeOper. xldv20TrActCcCreation. xldv20TrActCcDeletion. xldv… |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.3 | xldv20ActControlStatus | 1 | 1 | Indicates the status of a control request. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.4 | xldv20ActVpiNni | 1 | 1 | Identifies the VPI value associated with the Local Exchange. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.5 | xldv20ActVpiUni | 1 | 1 | The VPI value associated with the Network Termination. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.6 | xldv20ActVciNni | 1 | 1 | The VCI value associated with the Local Exchange. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.7 | xldv20ActVciUni | 1 | 1 | The VCI value associated with the Network Termination. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.8 | xldv20ActIfIndex | 1 | 1 | The relevant interface index of the connected PPTP . |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.9 | xldv20ActPeakCellRateUpstream | 1 | 1 | The upstream peak cell rate in bit/sec of the cross connect. ( Bit rate per ATM cell is 53*8 bit/sec ). |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.10 | xldv20ActPeakCellRateDownstream | 1 | 1 | The peak cell rate in downstream direction of the cross connect. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.11 | xldv20ActCellDelayVariationToleranceUpstream | 1 | 1 | The cell delay variation tolerance (in micro seconds) in upstream direction of the cross connect. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.12 | xldv20ActCellDelayVariationToleranceDownstream | 1 | 1 | The cell delay variation tolerance (in micro seconds) in downstream direction of the cross connect. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.13 | xldv20ActTrafficType | 1 | 1 | The traffic type of the cross connect. Supported traffic types are : cbr : Constant bit rate. ubr : Unspecified bit rate. nrt… |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.14 | xldv20ActTrafficDirection | 1 | 1 | The traffic direction. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.15 | xldv20ActSustainableCellRateUpstream | 1 | 1 | The upstream sustainable cell rate in bit/sec for nrtVbr traffic. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.16 | xldv20ActSustainableCellRateDownstream | 1 | 1 | The downstream sustainable cell rate in bit/sec for nrtVbr traffic. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.17 | xldv20ActMaximumBurstSizeUpstream | 1 | 1 | The upstream maximum burst size in cells for nrtVbr traffic. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.18 | xldv20ActMaximumBurstSizeDownstream | 1 | 1 | The downstream maximum burst size in cells for nrtVbr traffic. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.19 | xldv20ActSegmentEndPointNni | 1 | 1 | Specifies whether the NNI VplTp/VclTp/VpcTp is a segment endpoint (yes) or a connecting point (no) |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.20 | xldv20ActSegmentEndPointUni | 1 | 1 | Specifies whether the UNI VplTp/VclTp/VpcTp is a segment endpoint (yes) or a connecting point (no) |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.21 | xldv20ActEthMode | 1 | 1 | The operational mode of the ethernet configuration: Available modes: bridging, routing, currentCofiguration (default) . In version… |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.22 | xldv20ActEthE164Isp | 1 | 1 | The telephon number of the Internet Service Provider. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.23 | xldv20ActEthIpAddressNt | 1 | 1 | The IP Address of the NT. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.24 | xldv20ActEthIpAddressSubnetMaskNt | 1 | 1 | The subnet mask of the NT. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.25 | xldv20ActEthIpAddressCo | 1 | 1 | The IP Address of the destination NT (office side). |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.26 | xldv20ActEthIpAddressSubnetMaskCo | 1 | 1 | The subnet mask of the CO. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.27 | xldv20ActEthIpAddressRemoteRouter | 1 | 1 | The subnet mask of the ISP router. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.28 | xldv20ActTestTypeNni | 1 | 1 | The type of continuity check on NNI side. On F5 level (VC) segment only . |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.29 | xldv20ActContinuityCheckNni | 1 | 1 | Specifies whether or not the continuity check at NNI side should be enabled for this instance of the ATM Cross Connection managed… |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.30 | xldv20ActEndpointTypeNni | 1 | 1 | Specifies whether the NNI termination point VplTp/VclTp/VpcTp during countinuity check should be a source or sink or both (bidire… |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.31 | xldv20ActTestTypeUni | 1 | 1 | The type of continuity check on UNI side. On F5 level (VC) only segment. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.32 | xldv20ActContinuityCheckUni | 1 | 1 | Specifies whether or not the continuity check at UNI should be enabled for this instance of the ATM Cross Connection managed enti… |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.33 | xldv20ActEndpointTypeUni | 1 | 1 | Specifies whether the UNI termination point VplTp/VclTp/VpcTp during countinuity check should be source or sink or both (bidirect… |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.34 | xldv20ActControlReqResult | 1 | 1 | The result of the last user command. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.35 | xldv20ActInbandVpi | 1 | 1 | The value of the configured inband Vpi. The configured Vpi will be effective only after next reload. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.36 | xldv20ActInbandVci | 1 | 1 | The value of the configured inband Vci. The configured Vci will be effective only after next reload. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.37 | xldv20ActCallpTableIndex | 1 | 1 | After a successfull creation or deletion of a cross connect COH provides the index of the created or deleted object. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.38 | xldv20ActMaxVciValue | 1 | 1 | Configures the amount of VC's and their VCI values which are created within a VpcTp. Minimum VCI value is 32. Maximum VCI value is… |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.39 | xldv20ActVbrCDVTUpstream | 1 | 1 | The cell delay variation (in micro seconds) for VBR traffic in upstream direction. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.40 | xldv20ActVbrCDVTDownstream | 1 | 1 | The cell delay variation (in micro seconds) for VBR traffic in downstream direction. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.41 | xldv20ActControlTimeStamp | 1 | 1 | The time stamp of the last command (end of command). |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.42 | xldv20ActSegmentEndPointNt | 1 | 1 | Specifies whether the VplTp/VpcTp at the NT is a segment endpoint (yes) or a connecting point (no). |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.43 | xldv20ActTestTypeNt | 1 | 1 | The type of continuity check at NT (segment or endToEnd) . |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.44 | xldv20ActContinuityCheckNt | 1 | 1 | Specifies whether or not the continuity check at NT should be enabled . NOTE : continuity check not supported at VccTp (F5 level)… |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.45 | xldv20ActEndpointTypeNt | 1 | 1 | Specifies whether the endpoint VplTp/VpcTp at NT should be a source or sink or both (bidirectional connection only) for continuit… |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.1.46 | xldv20ActCDVTAutoConfig | 1 | 1 | If yes is selected the policing parameter CDVT (cell delay variation tolerance) is determined automatically depending on the confi… |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.2 | xldv20AtmCrossConnectTable | 1 | 11 | The ATM VP cross connect table. This managed entity is used to represent the cross-connect relationship between two Vpl terminati… |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.3 | xldv20VplTpTable | 1 | 25 | This table contains the entries for Vpl termination points (VplTp). |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.4 | xldv20VpcTpTable | 1 | 31 | This table contains the entries for VPC termination points. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.5 | xldv20VccTpTable | 1 | 14 | VccTp table for VC termination points. Entries are created for Ethernet NTs when cross connects are created. Entries are deleted w… |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.6 | xldv20VcCrossConnectTable | 1 | 13 | The VC cross connect table for Virtual Channel point-to-point cross connections. This managed entity is used to represent the VC-c… |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.7 | xldv20VclTpTable | 1 | 27 | This table contains the entries for the VC links. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.10 | xldv20EthernetConfigTable | 1 | 8 | The Ethernet Configuration Table. |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.11 | xldv20ContinuityCheckVpTable | 1 | 7 | The Continuity Check VP table. Holds entries for enabled continuity checks at VP level. Entries are created when Vpl cross connec… |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.12 | xldv20ContinuityCheckVcTable | 1 | 7 | The continuity check configuration table for COC on VC level. Entries in this table are created when Vcl cross connects with enabl… |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.13 | xldv20ContinuityCheckControl | 8 | 16 | None |
| 1.3.6.1.4.1.231.7.1.2.1.1.4.2.14 | xldv20InbandTmn | 4 | 8 | None |