Vendor: Nortel Networks
Module: Netwave-MIB (aspap.mib)
Type: OBJ ID
Access:
Syntax:
Automatically extracted from www.mibdepot.com
ntiASPAccessPoint OBJECT IDENTIFIER ::= { ntiMib 1 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2399.1.1.1 | ntiMIBRevisionLevel | 1 | 1 | MIB Revision level. |
| 1.3.6.1.4.1.2399.1.1.2 | ntiFirmwareVersion | 1 | 1 | Access Point Firmware Version. |
| 1.3.6.1.4.1.2399.1.1.3 | ntiIPAddress | 1 | 1 | Access Point's IP Address. Set a new IP address here. This takes effect on re-boot |
| 1.3.6.1.4.1.2399.1.1.4 | ntiRebootNow | 1 | 1 | Set to 1 to cause AP to shut down and reboot immediately. |
| 1.3.6.1.4.1.2399.1.1.5 | ntiHopSequenceAutoNegotiation | 1 | 1 | Set to 1 to allow auto-negotiation, 0 to use the agPhyFHSSGroup values as set. |
| 1.3.6.1.4.1.2399.1.1.6 | ntiIAPPAnnounceInterval | 1 | 1 | Number of secondes between IAPP broadcasts. |
| 1.3.6.1.4.1.2399.1.1.7 | ntiAccessControl | 3 | 8 | None |
| 1.3.6.1.4.1.2399.1.1.8 | ntiAssociatedUsersList | 1 | 3 | A list of MAC adress of units that are currently associated with this AP. |
| 1.3.6.1.4.1.2399.1.1.9 | ntiAdapterPowerControl | 1 | 1 | Control power to PC Card in Access Point. 0 - PC Card Power OFF. 1 - PC Card Power ON. |
| 1.3.6.1.4.1.2399.1.1.10 | ntiWMStatusSelfTestStatus | 1 | 1 | ntiWMStatusSelftestStatus |
| 1.3.6.1.4.1.2399.1.1.11 | ntiWMStatusCardInserted | 1 | 1 | 1 if PC Card is in slot. 0 if no PC Card in slot. |
| 1.3.6.1.4.1.2399.1.1.12 | ntiWMStatusIfOK | 1 | 1 | PC Card status. 1 = OK. |
| 1.3.6.1.4.1.2399.1.1.13 | ntiWMStatusBanner | 1 | 1 | Status banner from PC Card Adapter. |
| 1.3.6.1.4.1.2399.1.1.14 | ntiWMStatusNetwaveMode | 1 | 1 | 1 if PC Card in in Netwave Protocol mode. If so this adapter needs to be upgraded to 802.11 mode. |
| 1.3.6.1.4.1.2399.1.1.15 | ntiESSID | 1 | 1 | 802.11 Extended Service Set. |
| 1.3.6.1.4.1.2399.1.1.16 | ntiBSSBasicRateSet | 1 | 1 | 802.11 Basic rate set for this BSS. |
| 1.3.6.1.4.1.2399.1.1.17 | ntiSupportedRates | 1 | 1 | 802.11 rates supported by PC Card. |
| 1.3.6.1.4.1.2399.1.1.18 | ntiBeaconInterval | 1 | 1 | 802.11 number of milliseconds between TBTTs. |
| 1.3.6.1.4.1.2399.1.1.19 | ntiDTIMPeriod | 1 | 1 | 802.11 number of beacon intervals between DTIMs. |
| 1.3.6.1.4.1.2399.1.1.20 | ntiSNMPSecurity | 5 | 19 | None |
| 1.3.6.1.4.1.2399.1.1.21 | ntiTelnetMgmtEnable | 1 | 1 | 0 - Disable Telnet SNMP Management. 1 - Enable Telnet SNMP Management. |
| 1.3.6.1.4.1.2399.1.1.22 | ntiSetAllToFactoryDefaults | 1 | 1 | Set all Access Point Managable parameters to Factory defaults. |
| 1.3.6.1.4.1.2399.1.1.23 | ntiCommitConfigurationNow | 1 | 1 | Commit all of the SNMP managable to Flash. These will be used after re-boot. |
| 1.3.6.1.4.1.2399.1.1.24 | ntidot11 | 2 | 26 | None |
| 1.3.6.1.4.1.2399.1.1.25 | ntiPassword | 1 | 1 | Access Point Password. |
| 1.3.6.1.4.1.2399.1.1.26 | ntiLogout | 1 | 1 | Manager Logout of Access Point. |
| 1.3.6.1.4.1.2399.1.1.27 | ntiAULCountLimit | 1 | 1 | The maximum number of users that can be simultaneously associated with the Access Point. Range: 0 to 256. |
| 1.3.6.1.4.1.2399.1.1.28 | ntiPCCardCIS | 1 | 1 | The CIS of the PC Card in the Access Point. |
| 1.3.6.1.4.1.2399.1.1.29 | ntiStraightEncapsulation | 1 | 1 | 0 - 802.1h + NTI STT 1 - Straight Encapsulation 802.1h translation involves prepending a SNAP header with either an RFC1042 OUI or… |
| 1.3.6.1.4.1.2399.1.1.30 | ntiMVIAPPEnable | 1 | 1 | This boolean enables or disables the use of Multi- vendor IAPP. If this is disabled the AP will use Netwave's proprietary IAPP pr… |
| 1.3.6.1.4.1.2399.1.1.31 | ntiIPSubnetMask | 1 | 1 | Access Point's IP Subnet Mask. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits s… |
| 1.3.6.1.4.1.2399.1.1.32 | ntiIPGateway | 1 | 1 | Access Point's IP Gateway Address. Set a new IP Gateway address here. This takes effect on re-boot |
| 1.3.6.1.4.1.2399.1.1.33 | ntiAssociatedUsersCount | 1 | 1 | The current number of Users Associated with This AP. |
| 1.3.6.1.4.1.2399.1.1.34 | ntiWiredLinkMode | 1 | 1 | The desired mode of the wired link. |
| 1.3.6.1.4.1.2399.1.1.35 | ntiFailoverControl | 3 | 6 | None |
| 1.3.6.1.4.1.2399.1.1.36 | ntiEnableIPOnWirelessPort | 1 | 1 | When this attribute is enabled, a mobile unit on the wireless LAN shall able to send IP traffic destined to the AccessPoint. This… |
| 1.3.6.1.4.1.2399.1.1.37 | ntiWEPDefaultKeysStatus | 1 | 1 | A bit map that indicates whether or not each WEP default key has been set. The bits 0-3 of the bit map correspond to WEP default … |
| 1.3.6.1.4.1.2399.1.1.38 | ntiWEPKeyMappingsStatus | 1 | 1 | A bit map that indicates whether or not each WEP key mapping has been set. The bits 0-7 of the first octet of the bit map corresp… |
| 1.3.6.1.4.1.2399.1.1.1000 | ntiFWUpgradeFilename | 1 | 1 | Filename of Access Point Firmware upgrade image. |
| 1.3.6.1.4.1.2399.1.1.1001 | ntiAdapterFWUpgradeFilename | 1 | 1 | Filename of PC Card Firmware upgrade image. |
| 1.3.6.1.4.1.2399.1.1.1002 | ntiTFTPServerIPAddress | 1 | 1 | IP address of TFTP server where upgrade images are stored. |
| 1.3.6.1.4.1.2399.1.1.1003 | ntiWackyTestModeAddr | 1 | 1 | Wacky Test mode address.... |
| 1.3.6.1.4.1.2399.1.1.1004 | ntiWackyTestModeContents | 1 | 1 | 256 bytes of data from address: ntiWackyTestModeAddr. |
| 1.3.6.1.4.1.2399.1.1.1005 | ntiFreezeAUL | 1 | 1 | Set this to 1 to Freeze the AUL list. Clear it to thaw the AUL list. |
| 1.3.6.1.4.1.2399.1.1.1006 | ntiWackyClearErrorLog | 1 | 1 | Set to 1 to cause AP to clear it's error log. |
| 1.3.6.1.4.1.2399.1.1.1007 | ntiErrorStatus | 1 | 1 | The content of this object indicates the type of the last error, if any, occurred in the AccessPoint. |
| 1.3.6.1.4.1.2399.1.1.1008 | ntiClearErrorStatus | 1 | 1 | Setting this object to 1 has the effect of clearing the content of ntiErrorStatus. |