When this attribute is enabled, a mobile unit on the
wireless LAN shall able to send IP traffic destined to
the AccessPoint. This allows mobile units for pinging
the AccessPoint and for managing the AccessPoint via
BayStack AP Manager. The default value shall be disabled
Parsed from file bs650-660ap.mib.txt
Company: nortel
Module: Netwave-MIB
Child arc 0 is used to translate between SNMPv1 and SNMPv2 notification parameters as explained in IETF RFC 2576, section 3.
ntiEnableIPOnWirelessPort OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "When this attribute is enabled, a mobile unit on the wireless LAN shall able to send IP traffic destined to the AccessPoint. This allows mobile units for pinging the AccessPoint and for managing the AccessPoint via BayStack AP Manager. The default value shall be disabled" ::= { ntiASPAccessPoint 36 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.2399.1.1.36.0 | ntiEnableIPOnWirelessPort | 0 | 0 | None |
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.2399.1.1.1 | ntiMIBRevisionLevel | 1 | 1 | MIB Revision level. |
1.3.6.1.4.1.2399.1.1.2 | ntiFirmwareVersion | 1 | 1 | Access Point Firmware Version. |
1.3.6.1.4.1.2399.1.1.3 | ntiIPAddress | 1 | 1 | Access Point's IP Address. Set a new IP address here. This takes effect on re-boot |
1.3.6.1.4.1.2399.1.1.4 | ntiRebootNow | 1 | 1 | Set to 1 to cause AP to shut down and reboot immediately. |
1.3.6.1.4.1.2399.1.1.5 | ntiHopSequenceAutoNegotiation | 1 | 1 | Set to 1 to allow auto-negotiation, 0 to use the agPhyFHSSGroup values as set. |
1.3.6.1.4.1.2399.1.1.6 | ntiIAPPAnnounceInterval | 1 | 1 | Number of secondes between IAPP broadcasts. |
1.3.6.1.4.1.2399.1.1.7 | ntiAccessControl | 3 | 8 | None |
1.3.6.1.4.1.2399.1.1.8 | ntiAssociatedUsersList | 1 | 3 | A list of MAC adress of units that are currently associated with this AP. |
1.3.6.1.4.1.2399.1.1.9 | ntiAdapterPowerControl | 1 | 1 | Control power to PC Card in Access Point. 0 - PC Card Power OFF. 1 - PC Card Power ON. |
1.3.6.1.4.1.2399.1.1.10 | ntiWMStatusSelfTestStatus | 1 | 1 | ntiWMStatusSelftestStatus |
1.3.6.1.4.1.2399.1.1.11 | ntiWMStatusCardInserted | 1 | 1 | 1 if PC Card is in slot. 0 if no PC Card in slot. |
1.3.6.1.4.1.2399.1.1.12 | ntiWMStatusIfOK | 1 | 1 | PC Card status. 1 = OK. |
1.3.6.1.4.1.2399.1.1.13 | ntiWMStatusBanner | 1 | 1 | Status banner from PC Card Adapter. |
1.3.6.1.4.1.2399.1.1.14 | ntiWMStatusNetwaveMode | 1 | 1 | 1 if PC Card in in Netwave Protocol mode. If so this adapter needs to be upgraded to 802.11 mode. |
1.3.6.1.4.1.2399.1.1.15 | ntiESSID | 1 | 1 | 802.11 Extended Service Set. |
1.3.6.1.4.1.2399.1.1.16 | ntiBSSBasicRateSet | 1 | 1 | 802.11 Basic rate set for this BSS. |
1.3.6.1.4.1.2399.1.1.17 | ntiSupportedRates | 1 | 1 | 802.11 rates supported by PC Card. |
1.3.6.1.4.1.2399.1.1.18 | ntiBeaconInterval | 1 | 1 | 802.11 number of milliseconds between TBTTs. |
1.3.6.1.4.1.2399.1.1.19 | ntiDTIMPeriod | 1 | 1 | 802.11 number of beacon intervals between DTIMs. |
1.3.6.1.4.1.2399.1.1.20 | ntiSNMPSecurity | 5 | 19 | None |
1.3.6.1.4.1.2399.1.1.21 | ntiTelnetMgmtEnable | 1 | 1 | 0 - Disable Telnet SNMP Management. 1 - Enable Telnet SNMP Management. |
1.3.6.1.4.1.2399.1.1.22 | ntiSetAllToFactoryDefaults | 1 | 1 | Set all Access Point Managable parameters to Factory defaults. |
1.3.6.1.4.1.2399.1.1.23 | ntiCommitConfigurationNow | 1 | 1 | Commit all of the SNMP managable to Flash. These will be used after re-boot. |
1.3.6.1.4.1.2399.1.1.24 | ntidot11 | 2 | 26 | None |
1.3.6.1.4.1.2399.1.1.25 | ntiPassword | 1 | 1 | Access Point Password. |
1.3.6.1.4.1.2399.1.1.26 | ntiLogout | 1 | 1 | Manager Logout of Access Point. |
1.3.6.1.4.1.2399.1.1.27 | ntiAULCountLimit | 1 | 1 | The maximum number of users that can be simultaneously associated with the Access Point. Range: 0 to 256. |
1.3.6.1.4.1.2399.1.1.28 | ntiPCCardCIS | 1 | 1 | The CIS of the PC Card in the Access Point. |
1.3.6.1.4.1.2399.1.1.29 | ntiStraightEncapsulation | 1 | 1 | 0 - 802.1h + NTI STT 1 - Straight Encapsulation 802.1h translation involves prepending a SNAP header with either an RFC1042 OUI or… |
1.3.6.1.4.1.2399.1.1.30 | ntiMVIAPPEnable | 1 | 1 | This boolean enables or disables the use of Multi- vendor IAPP. If this is disabled the AP will use Netwave's proprietary IAPP pr… |
1.3.6.1.4.1.2399.1.1.31 | ntiIPSubnetMask | 1 | 1 | Access Point's IP Subnet Mask. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits s… |
1.3.6.1.4.1.2399.1.1.32 | ntiIPGateway | 1 | 1 | Access Point's IP Gateway Address. Set a new IP Gateway address here. This takes effect on re-boot |
1.3.6.1.4.1.2399.1.1.33 | ntiAssociatedUsersCount | 1 | 1 | The current number of Users Associated with This AP. |
1.3.6.1.4.1.2399.1.1.34 | ntiWiredLinkMode | 1 | 1 | The desired mode of the wired link. |
1.3.6.1.4.1.2399.1.1.35 | ntiFailoverControl | 3 | 6 | None |
1.3.6.1.4.1.2399.1.1.37 | ntiWEPDefaultKeysStatus | 1 | 1 | A bit map that indicates whether or not each WEP default key has been set. The bits 0-3 of the bit map correspond to WEP default … |
1.3.6.1.4.1.2399.1.1.38 | ntiWEPKeyMappingsStatus | 1 | 1 | A bit map that indicates whether or not each WEP key mapping has been set. The bits 0-7 of the first octet of the bit map corresp… |
1.3.6.1.4.1.2399.1.1.1000 | ntiFWUpgradeFilename | 1 | 1 | Filename of Access Point Firmware upgrade image. |
1.3.6.1.4.1.2399.1.1.1001 | ntiAdapterFWUpgradeFilename | 1 | 1 | Filename of PC Card Firmware upgrade image. |
1.3.6.1.4.1.2399.1.1.1002 | ntiTFTPServerIPAddress | 1 | 1 | IP address of TFTP server where upgrade images are stored. |
1.3.6.1.4.1.2399.1.1.1003 | ntiWackyTestModeAddr | 1 | 1 | Wacky Test mode address.... |
1.3.6.1.4.1.2399.1.1.1004 | ntiWackyTestModeContents | 1 | 1 | 256 bytes of data from address: ntiWackyTestModeAddr. |
1.3.6.1.4.1.2399.1.1.1005 | ntiFreezeAUL | 1 | 1 | Set this to 1 to Freeze the AUL list. Clear it to thaw the AUL list. |
1.3.6.1.4.1.2399.1.1.1006 | ntiWackyClearErrorLog | 1 | 1 | Set to 1 to cause AP to clear it's error log. |
1.3.6.1.4.1.2399.1.1.1007 | ntiErrorStatus | 1 | 1 | The content of this object indicates the type of the last error, if any, occurred in the AccessPoint. |
1.3.6.1.4.1.2399.1.1.1008 | ntiClearErrorStatus | 1 | 1 | Setting this object to 1 has the effect of clearing the content of ntiErrorStatus. |