This object specifies the interface or link used
as the Primary Reference Source for the system clock.
This may be derived internally, from the ATM network,
or from the CBR interface. It can be
1. Internal
2. ATM
3. CBR
Parsed from file mariposa.mib.txt
Company: marconi
Module: MARIPOSA-MIB
Vendor: Marconi
Module: MARIPOSA-MIB (mariposa.mib)
Type: TABULAR
Access: read-write
Syntax: INTEGER
Automatically extracted from www.mibdepot.com
atmDs3E3PhyParSystemClockSource OBJECT-TYPE SYNTAX INTEGER { int (1), atm (2), cbr (3) } ACCESS read-write STATUS mandatory DESCRIPTION "This object specifies the interface or link used as the Primary Reference Source for the system clock. This may be derived internally, from the ATM network, or from the CBR interface. It can be 1. Internal 2. ATM 3. CBR" ::= { atmDs3E3PhyParEntry 8 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2426.1.2.3.1.3.1.1.1.1 | atmDs3E3PhyParIfIndex | 0 | 0 | This value for this object is equal to the value of ifIndex from the Interfaces table of MIB II (RFC 1213). |
| 1.3.6.1.4.1.2426.1.2.3.1.3.1.1.1.2 | atmDs3E3PhyParInterfaceType | 0 | 0 | This object defines the interface type used. Valid values are: 1. Ds3 2. E3 |
| 1.3.6.1.4.1.2426.1.2.3.1.3.1.1.1.3 | atmDs3E3PhyParLineRate | 0 | 0 | This object defines the line rate in Mbps. Valid values are: 1. Ds3 interfaces: 44.736 2. E3 interfaces: 34.368 |
| 1.3.6.1.4.1.2426.1.2.3.1.3.1.1.1.4 | atmDs3E3PhyParLineCoding | 0 | 0 | This object specifies the type of zero code suppression used on the Ds3/E3 lines to maintain data integrity and reliability. Valid… |
| 1.3.6.1.4.1.2426.1.2.3.1.3.1.1.1.5 | atmDs3E3PhyParLineLength | 0 | 0 | The length of the ds3 / e3 line. This object provides information for line build out circuitry if it exists and can be used to adj… |
| 1.3.6.1.4.1.2426.1.2.3.1.3.1.1.1.6 | atmDs3E3PhyParLoopbackMode | 0 | 0 | This object defines the Loopback mode which may be the following 1. No Loopback Not in the loopback state. A device that is not ca… |
| 1.3.6.1.4.1.2426.1.2.3.1.3.1.1.1.7 | atmDs3E3PhyParTxClockSource | 0 | 0 | The source of Transmit Clock for the Ds3/E3 UNI.. 'loopTiming' indicates that the recovered receive clock is used as the transmit… |
| 1.3.6.1.4.1.2426.1.2.3.1.3.1.1.1.9 | atmDs3E3PhyParSystemClockSourceStatus | 0 | 0 | This objects specifies whether the clock source defined by 'systemClockSource' is refering to a valid resource or not. If the spe… |
| 1.3.6.1.4.1.2426.1.2.3.1.3.1.1.1.10 | atmDs3E3PhyParLossOfSignalState | 0 | 0 | Near end Loss Of Signal. The LOS failure is declared when the System cannot detect a signal at the ATM interface. When cells are … |
| 1.3.6.1.4.1.2426.1.2.3.1.3.1.1.1.11 | atmDs3E3PhyParLossOfFrameState | 0 | 0 | Near end LossOfFrame failure. The LOF failure is declared and this value is set to 'yes' (1) when framing bits have been lost at … |
| 1.3.6.1.4.1.2426.1.2.3.1.3.1.1.1.12 | atmDs3E3PhyAISFState | 0 | 0 | Far end sending Alarm Indication Signal(AIS): a signal sent down or up stream by a device regarding an error condition from anoth… |
| 1.3.6.1.4.1.2426.1.2.3.1.3.1.1.1.13 | atmDs3E3PhyXmtAISFState | 0 | 0 | Near end sending Alarm Indication Signal(AIS): a signal sent down or up stream by a device regarding an error condition from anot… |
| 1.3.6.1.4.1.2426.1.2.3.1.3.1.1.1.14 | atmDs3E3PhyXmtFarEndLOFFState | 0 | 0 | This object specifies whether the Near End is transmitting a LOF signal detected at the far end. The LOF failure is declared and … |
| 1.3.6.1.4.1.2426.1.2.3.1.3.1.1.1.15 | atmDs3E3PhyRcvFarEndLOFFState | 0 | 0 | This object specifies whether the Near End is receiving a LOF signal from the far end. The LOF failure is declared and this value… |
| 1.3.6.1.4.1.2426.1.2.3.1.3.1.1.1.16 | atmDs3E3PhyPlcpLOFState | 0 | 0 | This object specifies whether or not the DS3 PLCP has declared a loss of frame (LOF) failure condition. |
| 1.3.6.1.4.1.2426.1.2.3.1.3.1.1.1.17 | atmDs3E3PhyPlcpOOFState | 0 | 0 | This object specifies whether or not the DS3 PLCP has declared an out of frame (OOF) failure condition. |
| 1.3.6.1.4.1.2426.1.2.3.1.3.1.1.1.18 | atmDs3E3PhyPlcpYellowState | 0 | 0 | This object specifies whether or not the DS3 PLCP has received an incoming Yellow Signal from the far end. |
| 1.3.6.1.4.1.2426.1.2.3.1.3.1.1.1.19 | atmDs3E3PhyPlcpXmtYellowState | 0 | 0 | This object specifies whether or not the DS3 PLCP has declared a loss of frame (LOF) failure condition, and begun transmitting th… |