Positive Slip conditions detected since startup;
flags that the frequency of receive clock is less
than frequency of internal system clock
Parsed from file mibpmx.mib.txt
Company: None
Module: BIANCA-BRICK-PMX-MIB
Positive Slip conditions detected since startup;
flags that the frequency of receive clock is less
than frequency of internal system clock
Parsed from file BIANCA-BRICK-PMX-MIB.mib
Module: BIANCA-BRICK-PMX-MIB
Vendor: BinTec Communications GmbH
Module: BIANCA-BRICK-PMX-MIB
[Automatically extracted from oidview.com]
pmxIfSlipPositive OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Positive Slip conditions detected since startup; flags that the frequency of receive clock is less than frequency of internal system clock" ::= { pmxIfEntry 26 }
pmxIfSlipPositive OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Positive Slip conditions detected since startup; flags that the frequency of receive clock is less than frequency of internal system clock" ::= { pmxIfEntry 26 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.272.4.12.1.1.1 | pmxIfIndex | 0 | 0 | Unique Index of the primary rate interface. The index is similar to slotnumber * 1000 and is also refenced in the ifTable, the is… |
| 1.3.6.1.4.1.272.4.12.1.1.2 | pmxIfSelftest | 0 | 0 | The result of the initial selftest of the PMX module If the result is not succesful, the module is disabled successful(1) All se… |
| 1.3.6.1.4.1.272.4.12.1.1.3 | pmxIfLayer1State | 0 | 0 | The layer 1 state of the primary rate interface active(F1) active, framing and synchronisation is o.k. This is the only state wh… |
| 1.3.6.1.4.1.272.4.12.1.1.4 | pmxIfLayer1Mode | 0 | 0 | In T1 and E1 mode the primary rate interface is working with totaly different clock frequencies, framing and impedance. This depe… |
| 1.3.6.1.4.1.272.4.12.1.1.5 | pmxIfLayer1Framing | 0 | 0 | In T1 and E1 mode the primary rate interface can work with totaly different framing types on layer 1. The framing type must match… |
| 1.3.6.1.4.1.272.4.12.1.1.6 | pmxIfLayer1LineCode | 0 | 0 | In T1 mode the primary rate interface is able to work with different line codes. e1-hdb3(1) High Density Bipolar 3 Level Cod… |
| 1.3.6.1.4.1.272.4.12.1.1.7 | pmxIfChannelMode | 0 | 0 | In T1 and E1 mode the primary rate interface may work with different channel types. Usually every timeslot is similar to one chan… |
| 1.3.6.1.4.1.272.4.12.1.1.8 | pmxIfLoopbackMode | 0 | 0 | Loopback-Mode is only required for equipment test no-loop(1) do not loopanything, this is the correct mode for normal operation f… |
| 1.3.6.1.4.1.272.4.12.1.1.9 | pmxIfErrors | 0 | 0 | The measured PMX interface errors since startup |
| 1.3.6.1.4.1.272.4.12.1.1.10 | pmxIfPortMode | 0 | 0 | PortMode switches the CM-PRI's 'Out'-port normal(1) 'Out'-port is disabled, this CM-PRI is connected to 'In' go-thru(2) 'Out'-po… |
| 1.3.6.1.4.1.272.4.12.1.1.21 | pmxIfLOS | 0 | 0 | Loss Of Signal conditions since startup |
| 1.3.6.1.4.1.272.4.12.1.1.22 | pmxIfNoFAS | 0 | 0 | Loss Of Frame Alignment conditions since startup |
| 1.3.6.1.4.1.272.4.12.1.1.23 | pmxIfRemoteAlarms | 0 | 0 | Remote Alarms received since startup |
| 1.3.6.1.4.1.272.4.12.1.1.24 | pmxIfAlarmInds | 0 | 0 | Alarms received since startup |
| 1.3.6.1.4.1.272.4.12.1.1.25 | pmxIfCRC4Errors | 0 | 0 | CRC4 errors detected since startup |
| 1.3.6.1.4.1.272.4.12.1.1.27 | pmxIfSlipNegative | 0 | 0 | Negative Slip conditions detected since startup; flags that the frequency of receive clock is greater than frequency of internal … |