This object configures the maximum transmission rate for
the associated SHDSL Line in bits-per-second (bps). If
the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the maximum
line rate, the line rate is considered 'rate-adaptive'.
Parsed from file mibhdsl2shdsl.mib.txt
Company: bintec
Module: BIANCA-BRICK-HDSL2SHDSL-MIB
Vendor: Bintec
Module: BIANCA-BRICK-HDSL2SHDSL-MIB (mibhdsl2shdsl.mib)
Type: TABULAR
Access: read-write
Syntax: INTEGER
(
0..4640000 )
Automatically extracted from www.mibdepot.com
hdsl2ShdslSpanConfMaxLineRate OBJECT-TYPE SYNTAX INTEGER (0..4640000) ACCESS read-write STATUS mandatory DESCRIPTION "This object configures the maximum transmission rate for the associated SHDSL Line in bits-per-second (bps). If the minimum line rate equals the maximum line rate (hdsl2ShdslSpanMaxLineRate), the line rate is considered 'fixed'. If the minimum line rate is less than the maximum line rate, the line rate is considered 'rate-adaptive'." ::= { hdsl2ShdslSpanConfProfileEntry 4 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.272.4.35.1.1.10.1.1 | hdsl2ShdslSpanConfProfileName | 0 | 0 | This object is the unique index associated with this profile. Entries in this table are referenced via the object hdsl2ShdslSpanC… |
1.3.6.1.4.1.272.4.35.1.1.10.1.2 | hdsl2ShdslSpanConfWireInterface | 0 | 0 | This object configures the two-wire or optional four-wire operation for SHDSL Lines. |
1.3.6.1.4.1.272.4.35.1.1.10.1.3 | hdsl2ShdslSpanConfMinLineRate | 0 | 0 | This object configures the minimum transmission rate for the associated SHDSL Line in bits-per-second (bps). If the minimum line… |
1.3.6.1.4.1.272.4.35.1.1.10.1.5 | hdsl2ShdslSpanConfPSD | 0 | 0 | This object configures use of symmetric/asymmetric PSD (Power Spectral Density) Mask for the associated SHDSL Line. Support for … |
1.3.6.1.4.1.272.4.35.1.1.10.1.6 | hdsl2ShdslSpanConfTransmissionMode | 0 | 0 | hdsl2ShdslSpanConftransmissionMode |
1.3.6.1.4.1.272.4.35.1.1.10.1.7 | hdsl2ShdslSpanConfRemoteEnabled | 0 | 0 | This object enables/disables support for remote management of the units in a SHDSL line from the STU-R via the EOC. |
1.3.6.1.4.1.272.4.35.1.1.10.1.9 | hdsl2ShdslSpanConfCurrCondTargetMarginDown | 0 | 0 | This object specifies the downstream current condition target SNR margin for a SHDSL line. The SNR margin is the difference betw… |
1.3.6.1.4.1.272.4.35.1.1.10.1.10 | hdsl2ShdslSpanConfWorstCaseTargetMarginDown | 0 | 0 | This object specifies the downstream worst case target SNR margin for a SHDSL line. The SNR margin is the difference between the… |
1.3.6.1.4.1.272.4.35.1.1.10.1.11 | hdsl2ShdslSpanConfCurrCondTargetMarginUp | 0 | 0 | This object specifies the upstream current condition target SNR margin for a SHDSL line. The SNR margin is the difference betwee… |
1.3.6.1.4.1.272.4.35.1.1.10.1.12 | hdsl2ShdslSpanConfWorstCaseTargetMarginUp | 0 | 0 | This object specifies the upstream worst case target SNR margin for a SHDSL line. The SNR margin is the difference between the d… |
1.3.6.1.4.1.272.4.35.1.1.10.1.13 | hdsl2ShdslSpanConfUsedTargetMargins | 0 | 0 | Contains indicates whether a target SNR margin is enabled or disabled. This is a bit-map of possible settings. The various bit … |
1.3.6.1.4.1.272.4.35.1.1.10.1.14 | hdsl2ShdslSpanConfReferenceClock | 0 | 0 | This object configures the clock reference for the STU-C in a SHDSL Line. |
1.3.6.1.4.1.272.4.35.1.1.10.1.15 | hdsl2ShdslSpanConfLineProbeEnable | 0 | 0 | This object enables/disables support for Line Probe of the units in a SHDSL line. When Line Probe is enabled, the system perform… |