This indicates the DS0 in far end loopback.
Parsed from file cascade.mib.txt
Company: None
Module: CASCADE-MIB
This indicates the DS0 in far end loopback.
Parsed from file CASCADE-MIB.mib
Module: CASCADE-MIB
Vendor: Cascade Communications Corp.
Module: CASCADE-MIB
[Automatically extracted from oidview.com]
pportDS0FarendDS0InLpbk OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This indicates the DS0 in far end loopback." ::= { pportEntry 101 }
pportDS0FarendDS0InLpbk OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This indicates the DS0 in far end loopback." ::= { pportEntry 101 }
To many brothers! Only 100 nearest brothers are shown.
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| ... | ||||
| 1.3.6.1.4.1.277.1.4.2.1.51 | pportDS0LoopStatus | 0 | 0 | Bit map reporting which DS0's are currently in loopback. Low bit corresponds to DS0 1 |
| 1.3.6.1.4.1.277.1.4.2.1.52 | pportISDN | 0 | 0 | Specifies whether ISDN PRI is enabled for this physical port |
| 1.3.6.1.4.1.277.1.4.2.1.53 | pportdsx3LoopbackConfig | 0 | 0 | Integer used to set the loopback state of the DS3 or E3 |
| 1.3.6.1.4.1.277.1.4.2.1.54 | pportdsx3SendCode | 0 | 0 | Integer used to send loopback code to far-end DS3 |
| 1.3.6.1.4.1.277.1.4.2.1.55 | pportdsx3LoopStatus | 0 | 0 | Integer indicating the current loopback status of the DS3 or E3 |
| 1.3.6.1.4.1.277.1.4.2.1.56 | pportdsx3FEACStatus | 0 | 0 | Integer indicating the current DS3 FAEC status: DS3 Equipment Failure (1), DS3 LOS (2), DS3 Out of Frame (4), DS3 AIS receive… |
| 1.3.6.1.4.1.277.1.4.2.1.57 | pportds1LoopbackConfig | 0 | 0 | Integer used to set the loopback state of the DS1 |
| 1.3.6.1.4.1.277.1.4.2.1.58 | pportds1SendCode | 0 | 0 | Integer used to send loopback code to far-end DS1 |
| 1.3.6.1.4.1.277.1.4.2.1.59 | pportds1LoopStatus | 0 | 0 | Integer indicating the current loopback status of the DS1 |
| 1.3.6.1.4.1.277.1.4.2.1.60 | pportSetClkBkup | 0 | 0 | The desired clock source backup if the card is set in external clock source mode |
| 1.3.6.1.4.1.277.1.4.2.1.61 | pportAtmIdleWord | 0 | 0 | The word used to stuff the payload of the ATM idle cell |
| 1.3.6.1.4.1.277.1.4.2.1.62 | pportAtmDisCardMode | 0 | 0 | The desired clock source backup if the card is set in external clock source mode |
| 1.3.6.1.4.1.277.1.4.2.1.63 | pportAtmLastUnconfiguredVpi | 0 | 0 | This entry holds the Vpi read from the last Unconfigured atm cell received. This entry applies to ATM pports only. |
| 1.3.6.1.4.1.277.1.4.2.1.64 | pportAtmLastUnconfiguredVci | 0 | 0 | This entry holds the Vci read from the last Unconfigured atm cell received. This entry applies to ATM pports only. |
| 1.3.6.1.4.1.277.1.4.2.1.65 | pportAtmUnconfiguredCells | 0 | 0 | This entry holds a count of the number of Unconfigured ATM cells received. This entry applies to ATM pports only. |
| 1.3.6.1.4.1.277.1.4.2.1.66 | pportAtmNumBitsVCI | 0 | 0 | This entry holds a count of the VCI bits supported by this ATM card. |
| 1.3.6.1.4.1.277.1.4.2.1.67 | pportAtmNumBitsVPI | 0 | 0 | This entry holds a count of the VPI bits supported by this ATM card. |
| 1.3.6.1.4.1.277.1.4.2.1.68 | pportAtmInterfaceType | 0 | 0 | Integer used to set ATM UNI or NNI type |
| 1.3.6.1.4.1.277.1.4.2.1.69 | pportSonetSDHLoopbackConfig | 0 | 0 | Integer used to set the loopback state of the Sonet/SDH port |
| 1.3.6.1.4.1.277.1.4.2.1.70 | pportSonetSDHLoopStatus | 0 | 0 | Integer indicating the current loopback status of the Sonet/SDH port |
| 1.3.6.1.4.1.277.1.4.2.1.71 | pportOutDiscardsCell | 0 | 0 | The total number of outbound cell discarded due to congestion. |
| 1.3.6.1.4.1.277.1.4.2.1.72 | pportAtmPlcp | 0 | 0 | The PLCP maintains the state of the ATM Physical Layer Convergence Protocol. When the protocol is disabled atm direct mapping is … |
| 1.3.6.1.4.1.277.1.4.2.1.73 | pportCbrTargetClockMode | 0 | 0 | The clocking method to be used by the CBR card. 4-port CBR card 1 - synchronous (external) clocking 2 - SRTS clocking 3 - adaptive… |
| 1.3.6.1.4.1.277.1.4.2.1.74 | pportCbrCurrentClockMode | 0 | 0 | The clocking method currently used by the CBR card. 4-port CBR card 1 - synchronous (external) clocking 2 - SRTS clocking 3 - adap… |
| 1.3.6.1.4.1.277.1.4.2.1.75 | pportClockMasterChannel | 0 | 0 | The number of the channel (lport) on this pport that is used as ACM/SRTS master for this line interface: 4-port CBR E1/DS1 card (… |
| 1.3.6.1.4.1.277.1.4.2.1.76 | pportFibreType, pportFiberType | 0 | 0 | The type of fibre connected to the ATM-IWU. Its type determines the maximum transmission distance. 1-port ATM-IWU STM-1/STS-3c ca… |
| 1.3.6.1.4.1.277.1.4.2.1.77 | pportLaserStatus | 0 | 0 | The configured state of the laser: 1-port ATM-IWU STM-1/STS-3c card & Topaz 4-port OC3 & STM-1 card 1 - off 2 - on |
| 1.3.6.1.4.1.277.1.4.2.1.78 | pportMaxActiveVpiBits | 0 | 0 | The maximum number of active VPI bits configured for use at the ATM interface. At the ATM UNI, the maximum number of active VPI … |
| 1.3.6.1.4.1.277.1.4.2.1.79 | pportBipErrorsThresh | 0 | 0 | The threshold of BIP errors. If the number of line BIP-24/8 rrors persists to exceed this value, the pport will be taken down and… |
| 1.3.6.1.4.1.277.1.4.2.1.80 | pportBipSectionErrors | 0 | 0 | The number of B1 section BIP-8 errors since the last reset. |
| 1.3.6.1.4.1.277.1.4.2.1.81 | pportBipLineErrors | 0 | 0 | The number of line BIP-24/8 errors since the last reset. |
| 1.3.6.1.4.1.277.1.4.2.1.82 | pportBipPathErrors | 0 | 0 | The number of B3 path BIP-8 errors since the last reset. |
| 1.3.6.1.4.1.277.1.4.2.1.83 | pportFebeErrors | 0 | 0 | The number of line Far End Block Errors since the last reset. |
| 1.3.6.1.4.1.277.1.4.2.1.84 | pportHcsErrors | 0 | 0 | The number of correctable HCS errors since the last reset. |
| 1.3.6.1.4.1.277.1.4.2.1.85 | pportHcsSevereErrors | 0 | 0 | The number of uncorrectable HCS errors since the last reset. |
| 1.3.6.1.4.1.277.1.4.2.1.86 | pportCongestedReceivedCells | 0 | 0 | The number of received cells that were discarded due to congestion of the ATM-IWU, since the last reset. |
| 1.3.6.1.4.1.277.1.4.2.1.87 | pportCongestedTransmittedCells | 0 | 0 | The number of cells to be transmitted, that were discarded due to congestion of the ATM-IWU, since the last reset. |
| 1.3.6.1.4.1.277.1.4.2.1.88 | pportAtmLayerErroredReceivedCells | 0 | 0 | The number of received cells that were discarded due to ATM layer errors, since the last reset. |
| 1.3.6.1.4.1.277.1.4.2.1.89 | pportAtmLayerErroredTransmittedCells | 0 | 0 | The number of cells to be transmitted, that were discarded due to ATM layer errors, since the last reset. |
| 1.3.6.1.4.1.277.1.4.2.1.90 | pportDS0BitStuff | 0 | 0 | Bit stuffing on or off for 2047 bit pattern in DS0 far end testing. |
| 1.3.6.1.4.1.277.1.4.2.1.91 | pportDS0BitErrorCount | 0 | 0 | Total number of errors in 2047 DS0 far end testing. |
| 1.3.6.1.4.1.277.1.4.2.1.92 | pportDS0BitErrorFreeSeconds | 0 | 0 | Total number of error free seconds in 2047 DS0 far end testing. |
| 1.3.6.1.4.1.277.1.4.2.1.93 | pportDS0BitErroredSeconds | 0 | 0 | Total number of errored seconds in 2047 DS0 far end testing. |
| 1.3.6.1.4.1.277.1.4.2.1.94 | pportDS0MidspanRepeaters | 0 | 0 | Number of Midspan repeaters in a link to be punched thru for DS0 far end testing. |
| 1.3.6.1.4.1.277.1.4.2.1.95 | pportDS0TestPatternSync | 0 | 0 | While DS0 far end testing, the DS0 pattern has detected the pattern four consecutive times. If the pattern is lost, this variab… |
| 1.3.6.1.4.1.277.1.4.2.1.96 | pportDS0InjectBitError | 0 | 0 | While testing DS0 far end lpbk, setting this variable will inject a bit error into the test pattern. |
| 1.3.6.1.4.1.277.1.4.2.1.97 | pportDS0FarendLpbkType | 0 | 0 | The type of DS0 equipment to be looped back at the far end during DS0 far end testing. 1 - OCU 2 - DSU 3 - CSU. |
| 1.3.6.1.4.1.277.1.4.2.1.98 | pportDS0LpbkMode | 0 | 0 | This determines what mode the DS0 Processor will be set to. 1 - no lpbk 2 - switch lpbk 3 - far end lpbk. |
| 1.3.6.1.4.1.277.1.4.2.1.99 | pportDS0SwitchLpbkStart | 0 | 0 | This is the first DS0 in a sting of consecutive DS0's to be looped back at the switch if the DS0 processor is set to switch loopb… |
| 1.3.6.1.4.1.277.1.4.2.1.100 | pportDS0SwitchLpbkEnd | 0 | 0 | This is the Last DS0, +1, in a sting of consecutive DS0's to be looped back at the switch if the DS0 processor is set to switch l… |
| 1.3.6.1.4.1.277.1.4.2.1.102 | pportDS0SendTestTraffic | 0 | 0 | Enable or Disable sending DS0 2047 test pattern for DS0 far end testing. |
| 1.3.6.1.4.1.277.1.4.2.1.103 | pportOc3LoopConfig | 0 | 0 | The loopback state of the ATM IWU OC3 |
| 1.3.6.1.4.1.277.1.4.2.1.104 | pportOc3LoopStatus | 0 | 0 | The current loopback status of the ATM IWU OC3 |
| 1.3.6.1.4.1.277.1.4.2.1.105 | pportISDNIpBaseAddr | 0 | 0 | Specifies the base address used for IP Dynamic Address Assignment |
| 1.3.6.1.4.1.277.1.4.2.1.106 | pportSonetSTM1Scramble | 0 | 0 | Configured SONET/STM-1 scrambling. |
| 1.3.6.1.4.1.277.1.4.2.1.107 | pportEFCIMarking | 0 | 0 | Configured EFCI marking for cell traffic in Topaz IOMs |
| 1.3.6.1.4.1.277.1.4.2.1.108 | pportAtmQOSTransmitMode | 0 | 0 | Select fix priority or weighted round-robin for cell transmission in different ATM QOS classes. |
| 1.3.6.1.4.1.277.1.4.2.1.109 | pportHECMode | 0 | 0 | Configured ATM HEC single bit error correction routine. |
| 1.3.6.1.4.1.277.1.4.2.1.110 | pportISDNChannelStatus | 0 | 0 | The ISDN call status of all the B-Channels on the pport are encoded into this 24 character, (for T1 ISDN PRI card...23B+D) or 31… |
| 1.3.6.1.4.1.277.1.4.2.1.111 | pportds1FarEndLoopStatus | 0 | 0 | DS1 Far End Loopback Status as commanded by the switch |
| 1.3.6.1.4.1.277.1.4.2.1.112 | pportds1FDLControl | 0 | 0 | Enables or Disables FDL Function for DS1 ESF pport |
| 1.3.6.1.4.1.277.1.4.2.1.113 | pportds1FDLPrmXmit | 0 | 0 | Enables or Disables transmission of Performance Monitoring Report (PRM) messages on the DS1 ESF FDL |
| 1.3.6.1.4.1.277.1.4.2.1.114 | pportds1FDLPidXmit | 0 | 0 | Enables or Disables transmission of Path ID (PID) messages on the DS1 ESF FDL |
| 1.3.6.1.4.1.277.1.4.2.1.115 | pportds1FDLXmitPid | 0 | 0 | Transmit Path Id to be sent on the DS1 ESF FDL. (76 bytes) |
| 1.3.6.1.4.1.277.1.4.2.1.116 | pportds1FDLRcvPid | 0 | 0 | The last path id message received on the DS1 ESF FDL. (76 bytes) |
| 1.3.6.1.4.1.277.1.4.2.1.117 | pportds1FDLRcvTsid | 0 | 0 | The last test id message received on the DS1 ESF FDL. (76 bytes) |
| 1.3.6.1.4.1.277.1.4.2.1.118 | pportSonetSDHFramingMode | 0 | 0 | The Framing mode for SONET/SDH port interface types. |
| 1.3.6.1.4.1.277.1.4.2.1.119 | pportds1InbandLoopType | 0 | 0 | Integer used to distinguish Inband Line loopback code sent from the switch when commanding inband line loopbacks, and reckognized… |
| 1.3.6.1.4.1.277.1.4.2.1.120 | pportESFDataLinkStatus | 0 | 0 | The current status of the DS1 ESF (FDL) data link. |
| 1.3.6.1.4.1.277.1.4.2.1.121 | pportPMTcaId | 0 | 0 | This object identifies the the most recently declared pport threshold crossing alert |
| 1.3.6.1.4.1.277.1.4.2.1.122 | pportBchanTimerValue | 0 | 0 | This value is used on a per port basis to add a delay to answering a ISDN call of the initial Disconnect from the network. This … |
| 1.3.6.1.4.1.277.1.4.2.1.123 | pportAAL5CRC32Error | 0 | 0 | Number of received AAL5 packets with CRC32 errors. |
| 1.3.6.1.4.1.277.1.4.2.1.124 | pportAAL5CPIError | 0 | 0 | Number of received AAL5 packets with CPI errors The only valid value currently defined for the CPI field is all zeros |
| 1.3.6.1.4.1.277.1.4.2.1.125 | pportAAL5LengthError | 0 | 0 | Number of received AAL5 packets which satisfied one of the following error conditions: 1. number of received cells * 48 bytes - l… |
| 1.3.6.1.4.1.277.1.4.2.1.126 | pportAAL5ReassemblyTimerError | 0 | 0 | Number of expired reassembly timers |
| 1.3.6.1.4.1.277.1.4.2.1.127 | pportAAL5MaxNrSegError | 0 | 0 | Number of received AAL5 packets which exceeds the maximum allowed length |
| 1.3.6.1.4.1.277.1.4.2.1.128 | pportRedundancyArch | 0 | 0 | Pport redundancy architecture. Default is disabled. aps-intracard aps-intercard-resilient-uni cards, resilient UNI is used to rer… |
| 1.3.6.1.4.1.277.1.4.2.1.129 | pportAPSadminDir | 0 | 0 | Provisioned APS switch-direction-mode. Default is uni- directional. |
| 1.3.6.1.4.1.277.1.4.2.1.130 | pportAPSlineType | 0 | 0 | APS line type for the pport. Writable only when pportRedundancyArch is disabled. |
| 1.3.6.1.4.1.277.1.4.2.1.131 | pportAPSrevertiveMode | 0 | 0 | APS revertive mode. When revertive, after the condition for an automatic switchover clears, user traffic will be switched back t… |
| 1.3.6.1.4.1.277.1.4.2.1.132 | pportAPSpairedSlotId | 0 | 0 | Slot ID of the paired-with APS pport. Writable only when pportRedundancyArch is disabled. |
| 1.3.6.1.4.1.277.1.4.2.1.133 | pportAPSpairedPportId | 0 | 0 | Pport ID of the paired-with APS pport. Writable only when pportRedundancyARch is disabled. |
| 1.3.6.1.4.1.277.1.4.2.1.134 | pportAPSsfBerThresh | 0 | 0 | Exponent N for APS Signal Failure based on BER. A line bit-error-rate above 10^-N causes an SF BER failure to be asserted. SF B… |
| 1.3.6.1.4.1.277.1.4.2.1.135 | pportAPSsdBerThresh | 0 | 0 | Exponent N for APS Signal Degrade based on BER. A line bit-error-rate above 10^-N causes an SD BER failure to be asserted. SD B… |
| 1.3.6.1.4.1.277.1.4.2.1.136 | pportAPSwtrPeriod | 0 | 0 | APS wait-to-restore period. The number of minutes to wait after an automatic switch condition clears before switching back to th… |
| 1.3.6.1.4.1.277.1.4.2.1.137 | pportAPSprotectionLineState | 0 | 0 | Indicates the state of the protection line selector. When selected, a protection switchover has taken place and user traffic is b… |
| 1.3.6.1.4.1.277.1.4.2.1.138 | pportAPSxCommand | 0 | 0 | External switch commands. The clear command clears any previously activated external command. Manual switch is preemptable by a… |
| 1.3.6.1.4.1.277.1.4.2.1.139 | pportAPSconfigStatus | 0 | 0 | Status of APS pport configuration. The not-configured status indicates the pport APS feature is not configured or it is a non-AP… |
| 1.3.6.1.4.1.277.1.4.2.1.140 | pportAPSOperRxStatus | 0 | 0 | The current state of the pair of APS pports with respect to the ability of the pair to Receive user traffic. When indicated as u… |
| 1.3.6.1.4.1.277.1.4.2.1.141 | pportBertPattern | 0 | 0 | Pattern generated by the XBERT |
| 1.3.6.1.4.1.277.1.4.2.1.142 | pportBertUserBytes | 0 | 0 | Definition of 1,2,3 or 4 byte pattern if UserNByte selected. |
| 1.3.6.1.4.1.277.1.4.2.1.143 | pportBertErrorRate | 0 | 0 | Error rate to insert in generated pattern. |
| 1.3.6.1.4.1.277.1.4.2.1.144 | pportBertCommand | 0 | 0 | Single shot commands to the BERT. |
| 1.3.6.1.4.1.277.1.4.2.1.145 | pportBertStatus | 0 | 0 | Current status of the BERT for this channel. |
| 1.3.6.1.4.1.277.1.4.2.1.146 | pportBertBitCount | 0 | 0 | The number of bits received - stops counting at 0xFFFFFFFF |
| 1.3.6.1.4.1.277.1.4.2.1.147 | pportBertErrorCount | 0 | 0 | The number of bits received in error- stops counting at 0xFFFFFFFF |
| 1.3.6.1.4.1.277.1.4.2.1.148 | pportds1FELoopbackControl | 0 | 0 | Enables or Disables Far end loopback control of the switch. Enabled (2) = Loop up and down commands from far end equipment will b… |
| 1.3.6.1.4.1.277.1.4.2.1.149 | pportFT1DS0s | 0 | 0 | DS0 usage bitmask for Fractional T1/E1 data rates. |
| 1.3.6.1.4.1.277.1.4.2.1.150 | pportIMUXCnt | 0 | 0 | DS3 Inverse Multiplexer counter value - specifies number of idle cells to insert by the outbound process Hardware. |
| 1.3.6.1.4.1.277.1.4.2.1.151 | pportds1PMConfigThresh | 0 | 0 | The setting determines which standard is used for performance monitoring configuration thresholds |
| ... | ||||