Vendor: Cascade Communications Corp.
Module: CASCADE-MIB
[Automatically extracted from oidview.com]
pportIdleCellType OBJECT-TYPE SYNTAX INTEGER { atmforum (1), itu (2) } ACCESS read-write STATUS mandatory DESCRIPTION "The setting determines the type of Idle/unassigned cell transmitted by the pport. 1 2 ::= { pportEntry 152 }
pportIdleCellType OBJECT-TYPE SYNTAX INTEGER { atmforum (1), itu (2) } ACCESS read-write STATUS mandatory DESCRIPTION "The setting determines the type of Idle/unassigned cell transmitted by the pport. 1 2 ::= { pportEntry 152 }
To many brothers! Only 100 nearest brothers are shown.
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| ... | ||||
| 1.3.6.1.4.1.277.1.4.2.1.102 | pportDS0SendTestTraffic | 0 | 0 | Enable or Disable sending DS0 2047 test pattern for DS0 far end testing. |
| 1.3.6.1.4.1.277.1.4.2.1.103 | pportOc3LoopConfig | 0 | 0 | The loopback state of the ATM IWU OC3 |
| 1.3.6.1.4.1.277.1.4.2.1.104 | pportOc3LoopStatus | 0 | 0 | The current loopback status of the ATM IWU OC3 |
| 1.3.6.1.4.1.277.1.4.2.1.105 | pportISDNIpBaseAddr | 0 | 0 | Specifies the base address used for IP Dynamic Address Assignment |
| 1.3.6.1.4.1.277.1.4.2.1.106 | pportSonetSTM1Scramble | 0 | 0 | Configured SONET/STM-1 scrambling. |
| 1.3.6.1.4.1.277.1.4.2.1.107 | pportEFCIMarking | 0 | 0 | Configured EFCI marking for cell traffic in Topaz IOMs |
| 1.3.6.1.4.1.277.1.4.2.1.108 | pportAtmQOSTransmitMode | 0 | 0 | Select fix priority or weighted round-robin for cell transmission in different ATM QOS classes. |
| 1.3.6.1.4.1.277.1.4.2.1.109 | pportHECMode | 0 | 0 | Configured ATM HEC single bit error correction routine. |
| 1.3.6.1.4.1.277.1.4.2.1.110 | pportISDNChannelStatus | 0 | 0 | The ISDN call status of all the B-Channels on the pport are encoded into this 24 character, (for T1 ISDN PRI card...23B+D) or 31… |
| 1.3.6.1.4.1.277.1.4.2.1.111 | pportds1FarEndLoopStatus | 0 | 0 | DS1 Far End Loopback Status as commanded by the switch |
| 1.3.6.1.4.1.277.1.4.2.1.112 | pportds1FDLControl | 0 | 0 | Enables or Disables FDL Function for DS1 ESF pport |
| 1.3.6.1.4.1.277.1.4.2.1.113 | pportds1FDLPrmXmit | 0 | 0 | Enables or Disables transmission of Performance Monitoring Report (PRM) messages on the DS1 ESF FDL |
| 1.3.6.1.4.1.277.1.4.2.1.114 | pportds1FDLPidXmit | 0 | 0 | Enables or Disables transmission of Path ID (PID) messages on the DS1 ESF FDL |
| 1.3.6.1.4.1.277.1.4.2.1.115 | pportds1FDLXmitPid | 0 | 0 | Transmit Path Id to be sent on the DS1 ESF FDL. (76 bytes) |
| 1.3.6.1.4.1.277.1.4.2.1.116 | pportds1FDLRcvPid | 0 | 0 | The last path id message received on the DS1 ESF FDL. (76 bytes) |
| 1.3.6.1.4.1.277.1.4.2.1.117 | pportds1FDLRcvTsid | 0 | 0 | The last test id message received on the DS1 ESF FDL. (76 bytes) |
| 1.3.6.1.4.1.277.1.4.2.1.118 | pportSonetSDHFramingMode | 0 | 0 | The Framing mode for SONET/SDH port interface types. |
| 1.3.6.1.4.1.277.1.4.2.1.119 | pportds1InbandLoopType | 0 | 0 | Integer used to distinguish Inband Line loopback code sent from the switch when commanding inband line loopbacks, and reckognized… |
| 1.3.6.1.4.1.277.1.4.2.1.120 | pportESFDataLinkStatus | 0 | 0 | The current status of the DS1 ESF (FDL) data link. |
| 1.3.6.1.4.1.277.1.4.2.1.121 | pportPMTcaId | 0 | 0 | This object identifies the the most recently declared pport threshold crossing alert |
| 1.3.6.1.4.1.277.1.4.2.1.122 | pportBchanTimerValue | 0 | 0 | This value is used on a per port basis to add a delay to answering a ISDN call of the initial Disconnect from the network. This … |
| 1.3.6.1.4.1.277.1.4.2.1.123 | pportAAL5CRC32Error | 0 | 0 | Number of received AAL5 packets with CRC32 errors. |
| 1.3.6.1.4.1.277.1.4.2.1.124 | pportAAL5CPIError | 0 | 0 | Number of received AAL5 packets with CPI errors The only valid value currently defined for the CPI field is all zeros |
| 1.3.6.1.4.1.277.1.4.2.1.125 | pportAAL5LengthError | 0 | 0 | Number of received AAL5 packets which satisfied one of the following error conditions: 1. number of received cells * 48 bytes - l… |
| 1.3.6.1.4.1.277.1.4.2.1.126 | pportAAL5ReassemblyTimerError | 0 | 0 | Number of expired reassembly timers |
| 1.3.6.1.4.1.277.1.4.2.1.127 | pportAAL5MaxNrSegError | 0 | 0 | Number of received AAL5 packets which exceeds the maximum allowed length |
| 1.3.6.1.4.1.277.1.4.2.1.128 | pportRedundancyArch | 0 | 0 | Pport redundancy architecture. Default is disabled. aps-intracard aps-intercard-resilient-uni cards, resilient UNI is used to rer… |
| 1.3.6.1.4.1.277.1.4.2.1.129 | pportAPSadminDir | 0 | 0 | Provisioned APS switch-direction-mode. Default is uni- directional. |
| 1.3.6.1.4.1.277.1.4.2.1.130 | pportAPSlineType | 0 | 0 | APS line type for the pport. Writable only when pportRedundancyArch is disabled. |
| 1.3.6.1.4.1.277.1.4.2.1.131 | pportAPSrevertiveMode | 0 | 0 | APS revertive mode. When revertive, after the condition for an automatic switchover clears, user traffic will be switched back t… |
| 1.3.6.1.4.1.277.1.4.2.1.132 | pportAPSpairedSlotId | 0 | 0 | Slot ID of the paired-with APS pport. Writable only when pportRedundancyArch is disabled. |
| 1.3.6.1.4.1.277.1.4.2.1.133 | pportAPSpairedPportId | 0 | 0 | Pport ID of the paired-with APS pport. Writable only when pportRedundancyARch is disabled. |
| 1.3.6.1.4.1.277.1.4.2.1.134 | pportAPSsfBerThresh | 0 | 0 | Exponent N for APS Signal Failure based on BER. A line bit-error-rate above 10^-N causes an SF BER failure to be asserted. SF B… |
| 1.3.6.1.4.1.277.1.4.2.1.135 | pportAPSsdBerThresh | 0 | 0 | Exponent N for APS Signal Degrade based on BER. A line bit-error-rate above 10^-N causes an SD BER failure to be asserted. SD B… |
| 1.3.6.1.4.1.277.1.4.2.1.136 | pportAPSwtrPeriod | 0 | 0 | APS wait-to-restore period. The number of minutes to wait after an automatic switch condition clears before switching back to th… |
| 1.3.6.1.4.1.277.1.4.2.1.137 | pportAPSprotectionLineState | 0 | 0 | Indicates the state of the protection line selector. When selected, a protection switchover has taken place and user traffic is b… |
| 1.3.6.1.4.1.277.1.4.2.1.138 | pportAPSxCommand | 0 | 0 | External switch commands. The clear command clears any previously activated external command. Manual switch is preemptable by a… |
| 1.3.6.1.4.1.277.1.4.2.1.139 | pportAPSconfigStatus | 0 | 0 | Status of APS pport configuration. The not-configured status indicates the pport APS feature is not configured or it is a non-AP… |
| 1.3.6.1.4.1.277.1.4.2.1.140 | pportAPSOperRxStatus | 0 | 0 | The current state of the pair of APS pports with respect to the ability of the pair to Receive user traffic. When indicated as u… |
| 1.3.6.1.4.1.277.1.4.2.1.141 | pportBertPattern | 0 | 0 | Pattern generated by the XBERT |
| 1.3.6.1.4.1.277.1.4.2.1.142 | pportBertUserBytes | 0 | 0 | Definition of 1,2,3 or 4 byte pattern if UserNByte selected. |
| 1.3.6.1.4.1.277.1.4.2.1.143 | pportBertErrorRate | 0 | 0 | Error rate to insert in generated pattern. |
| 1.3.6.1.4.1.277.1.4.2.1.144 | pportBertCommand | 0 | 0 | Single shot commands to the BERT. |
| 1.3.6.1.4.1.277.1.4.2.1.145 | pportBertStatus | 0 | 0 | Current status of the BERT for this channel. |
| 1.3.6.1.4.1.277.1.4.2.1.146 | pportBertBitCount | 0 | 0 | The number of bits received - stops counting at 0xFFFFFFFF |
| 1.3.6.1.4.1.277.1.4.2.1.147 | pportBertErrorCount | 0 | 0 | The number of bits received in error- stops counting at 0xFFFFFFFF |
| 1.3.6.1.4.1.277.1.4.2.1.148 | pportds1FELoopbackControl | 0 | 0 | Enables or Disables Far end loopback control of the switch. Enabled (2) = Loop up and down commands from far end equipment will b… |
| 1.3.6.1.4.1.277.1.4.2.1.149 | pportFT1DS0s | 0 | 0 | DS0 usage bitmask for Fractional T1/E1 data rates. |
| 1.3.6.1.4.1.277.1.4.2.1.150 | pportIMUXCnt | 0 | 0 | DS3 Inverse Multiplexer counter value - specifies number of idle cells to insert by the outbound process Hardware. |
| 1.3.6.1.4.1.277.1.4.2.1.151 | pportds1PMConfigThresh | 0 | 0 | The setting determines which standard is used for performance monitoring configuration thresholds |
| 1.3.6.1.4.1.277.1.4.2.1.153 | pportATMTcaInHECErrorUAlertPeriod | 0 | 0 | ATM tca ingress HEC error uncorrectable alert period (in min.). |
| 1.3.6.1.4.1.277.1.4.2.1.154 | pportATMTcaInHECErrorUThresh | 0 | 0 | ATM tca ingress HEC error uncorrectable threshold. |
| 1.3.6.1.4.1.277.1.4.2.1.155 | pportATMTcaEBufOverflowCBRAlertPeriod | 0 | 0 | ATM tca egress buffer overflow CBR Alert period (in min) |
| 1.3.6.1.4.1.277.1.4.2.1.156 | pportATMTcaEBufOverflowCBRThresh | 0 | 0 | ATM tca egress buffer overflow CBR threshold. |
| 1.3.6.1.4.1.277.1.4.2.1.157 | pportATMTcaEBufOverflowABRAlertPeriod | 0 | 0 | ATM tca egress buffer overflow ABR alert period (in min) |
| 1.3.6.1.4.1.277.1.4.2.1.158 | pportATMTcaEBufOverflowABRThresh | 0 | 0 | ATM tca egress buffer overflow ABR threshold. |
| 1.3.6.1.4.1.277.1.4.2.1.159 | pportATMTcaEBufOverflowVBR1AlertPeriod | 0 | 0 | ATM tca egress buffer overflow VBR1 alert period (in min) |
| 1.3.6.1.4.1.277.1.4.2.1.160 | pportATMTcaEBufOverflowVBR1Thresh | 0 | 0 | ATM tca egress buffer overflow VBR1 threshold. |
| 1.3.6.1.4.1.277.1.4.2.1.161 | pportATMTcaEBufOverflowVBR2AlertPeriod | 0 | 0 | ATM tca egress buffer overflow VBR2 alert period (in min) |
| 1.3.6.1.4.1.277.1.4.2.1.162 | pportATMTcaEBufOverflowVBR2Thresh | 0 | 0 | ATM tca egress buffer overflow VBR2 threshold. |
| 1.3.6.1.4.1.277.1.4.2.1.163 | pportATMTcaInFramerFIFOOverflowAlertPeriod | 0 | 0 | ATM tca ingress framer FIFO overflow alert period (in min) |
| 1.3.6.1.4.1.277.1.4.2.1.164 | pportATMTcaInFramerFIFOOverflowThresh | 0 | 0 | ATM tca ingress framer FIFO overflow threshold. |
| 1.3.6.1.4.1.277.1.4.2.1.165 | pportATMTcaELookupFailureAlertPeriod | 0 | 0 | ATM tca egress lookup failure alert period (in min) |
| 1.3.6.1.4.1.277.1.4.2.1.166 | pportATMTcaELookupFailureThresh | 0 | 0 | ATM tca egress lookup failure threshold. |
| 1.3.6.1.4.1.277.1.4.2.1.167 | pportATMTcaEnable | 0 | 0 | ATM tca port enable. |
| 1.3.6.1.4.1.277.1.4.2.1.168 | pportATMTcaId | 0 | 0 | This object identifies the the most recently declared pport ATM threshold crossing alert |
| 1.3.6.1.4.1.277.1.4.2.1.169 | pportFethAdminMacAddr, pportFethMacAddr | 0 | 0 | The configured MAC address to use for this Fast Ethernet port. Setting this to all zeros will force the port to use the burned in… |
| 1.3.6.1.4.1.277.1.4.2.1.170 | pportFethOperMacAddr | 0 | 0 | The actual MAC address in use for this Fast Ethernet port. |
| 1.3.6.1.4.1.277.1.4.2.1.171 | pportConfigAlarmSoakTime | 0 | 0 | This is the soak time for configurable alarms. An alarm of this type must persist for this period before it is declared. The ti… |
| 1.3.6.1.4.1.277.1.4.2.1.172 | pportConfigAlarmClearTime | 0 | 0 | This is the soak time for configurable alarms. An alarm of this type must remain clear for this period before it is declared to b… |
| 1.3.6.1.4.1.277.1.4.2.1.173 | pportFethPortCapability | 0 | 0 | Selection for the speed (10/100) and mode (half/full duplex) of operation for Fast Ethernet ports. |
| 1.3.6.1.4.1.277.1.4.2.1.174 | pportVpshapingDiscardCellCount | 0 | 0 | Cells discarded due to buffer overflow on this pport because of traffic shaping. |
| ... | ||||