The type of SS7 services (ISUP, TCAP, or both) supported by this SS7 Node entry.
As of GSX release 3.02.00, isupOnly is now the only vaild option for this entry.
Parsed from file sonusSs7Fe.mib.txt
Company: None
Module: SONUS-SS7-SERVICES-MIB
The type of SS7 services (ISUP, TCAP, or both) supported by this SS7 Node entry.
As of GSX release 3.02.00, isupOnly is now the only vaild option for this entry.
Parsed from file SONUS-SS7-SERVICES-MIB.mib
Module: SONUS-SS7-SERVICES-MIB
Vendor: Sonus Networks, Inc.
Module: SONUS-SS7-SERVICES-MIB
[Automatically extracted from oidview.com]
sonusSs7NodeServices OBJECT-TYPE SYNTAX INTEGER { isupOnly(1), tcapOnly(2), isupAndTcap(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The type of SS7 services (ISUP, TCAP, or both) supported by this SS7 Node entry. As of GSX release 3.02.00, isupOnly is now the only vaild option for this entry." DEFVAL { isupOnly } ::= { sonusSs7NodeEntry 5 }
sonusSs7NodeServices OBJECT-TYPE SYNTAX INTEGER { isupOnly(1), tcapOnly(2), isupAndTcap(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The type of SS7 services (ISUP, TCAP, or both) supported by this SS7 Node entry. As of GSX release 3.02.00, isupOnly is now the only vaild option for this entry." DEFVAL { isupOnly } ::= { sonusSs7NodeEntry 5 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.1 | sonusSs7NodeIndex | 0 | 0 | Identifies the target SS7 Node entry. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.2 | sonusSs7NodeState | 0 | 0 | The administrative state of this SS7 Node entry. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.3 | sonusSs7NodeName | 0 | 0 | The name of this SS7 Node instance. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.4 | sonusSs7NodePointCode | 0 | 0 | The SS7 point code assigned to this SS7 Node entry. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.6 | sonusSs7NodeProtocol | 0 | 0 | The SS7 protocol type supported by this SS7 Node entry. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.7 | sonusSs7NodeTcapSsn | 0 | 0 | If Tcap is supported by this SS7 Node, specifies the Sub System Number for this node entry. This object is obsoleted as of GSX re… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.8 | sonusSs7NodeIsupStatus | 0 | 0 | This status value has been replaced by sonusSs7NodeStatIsup |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.9 | sonusSs7NodeTcapStatus | 0 | 0 | Specifies the operating status of the TCAP service within this SS7 Node. This object is obsoleted as of GSX release 3.02.00. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.10 | sonusSs7NodeMtpStatus | 0 | 0 | This status value has been replaced by sonusSs7NodeStatMtp |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.11 | sonusSs7NodeGatewayAssignment | 0 | 0 | The name of the SS7 Gateway to which this SS7 Node is assigned. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.12 | sonusSs7NodeNativePointCode | 0 | 0 | The native point code of the SS7 node. e.g. For ITU the point code is in 3 bit 8 bit 3 bit format adding up to 14 bits whereas AN… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.13 | sonusSs7NodeMode | 0 | 0 | Specifies the service mode for this SS7 Node. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.14 | sonusSs7NodeConnCntrl | 0 | 0 | Specifies when the Node will establish an ISUP connection with the SS7 Gateway. This parameter is used to minimize unnecessary c… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.15 | sonusSs7NodeRowStatus | 0 | 0 | None |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.16 | sonusSs7NodeStdPointCode | 0 | 0 | Octet string of the point code. This gives the actual representation the user entered. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.17 | sonusSs7NodePointCodeSize | 0 | 0 | Indicates the total number of bits in the point code. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.18 | sonusSs7NodePointCodeFormatType | 0 | 0 | The Point Code format type being defined. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.19 | sonusSs7NodeServerProtocol | 0 | 0 | The interface used between the SS7 gateway and the SS7 client on the GSX9000 |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.20 | sonusSs7NodeHandShakeInterval | 0 | 0 | HandShake interval between the client and the server in seconds. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.21 | sonusSs7NodeTimerT1 | 0 | 0 | The Timer T1 could be changed from its default using this entry. The valid ranges are 4 - 15 seconds for ANSI and 15 - 60 Second… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.22 | sonusSs7NodeTimerT2 | 0 | 0 | The Timer T2 could be changed from its default using this entry. The valid value for ITU is 3 Minutes. This timer has no releven… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.23 | sonusSs7NodeTimerT3 | 0 | 0 | The T3 timer is started on receipt of an Overload message in the ITU network. This has no relevence in the ANSI network. The val… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.24 | sonusSs7NodeTimerT4 | 0 | 0 | The Timer T4 could be changed from its default using this entry. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.25 | sonusSs7NodeTimerT5 | 0 | 0 | The T5 Timer is started when the release message is sent. The valid values as per the specifications are 60 seconds for the ANSI… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.26 | sonusSs7NodeTimerT6 | 0 | 0 | The timer T6 is started when the suspend message is received. The valid range for this timer is 1 to 120 seconds. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.27 | sonusSs7NodeTimerT7 | 0 | 0 | The Timer T7 could be changed from its default using this entry. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.28 | sonusSs7NodeTimerT8 | 0 | 0 | The T8 timer is timer to be started with continuity check has been indicated in the IAM. The valid range is 10 to 15 seconds. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.29 | sonusSs7NodeTimerT9 | 0 | 0 | The Timer T9 started when outgoing international exchange recieves an ACM. The valid range is 120 to 240 seconds. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.30 | sonusSs7NodeTimerT10 | 0 | 0 | The Timer T10 is started when the last digit is recived in interworking situations. This timer has no relevence to ANSI. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.31 | sonusSs7NodeTimerT11 | 0 | 0 | The Timer T11 is started when the latest address message is received in interworking situations. The valid range is 15 to 20 sec… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.32 | sonusSs7NodeTimerT12 | 0 | 0 | The Timer T12 is started when a blocking message is sent. The valid ranges are 4 to 15 seconds for ANSI and 15 to 60 seconds for… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.33 | sonusSs7NodeTimerT13 | 0 | 0 | The Timer T13 is started when the initial blocking messge is sent. The valid value for ANSI is 60 seconds and for ITU is between… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.34 | sonusSs7NodeTimerT14 | 0 | 0 | The Timer T14 is started when an unblocking message is sent. The valid values are 4 to 15 seconds for ANSI and 15 to 60 seconds … |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.35 | sonusSs7NodeTimerT15 | 0 | 0 | The Timer T15 is started when the initial unblocking message is sent. The valid values are 60 seconds for ANSI and 300 to 900 se… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.36 | sonusSs7NodeTimerT16 | 0 | 0 | The Timer T16 is started when the reset circuit is started which was not due to expiry of T5. The valid ranges are 4 to 15 secon… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.37 | sonusSs7NodeTimerT17 | 0 | 0 | The Timer T17 is started when initial reset message is sent. The valid values are 60 seconds for ANSI and 300 to 900 for ITU. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.38 | sonusSs7NodeTimerT18 | 0 | 0 | The Timer T18 is started when circuit group blocking message is sent. The valid values are 4 to 15 seconds for ANSI and 15 to 60… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.39 | sonusSs7NodeTimerT19 | 0 | 0 | The Timer T19 is started when initial group blocking message is sent. The valid values are 60 seconds for ANSI and 300 to 900 se… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.40 | sonusSs7NodeTimerT20 | 0 | 0 | The Timer T20 is started when group unblocking message is sent. The valid ranges are 4 to 15 seconds for ANSI and 15 to 60 secon… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.41 | sonusSs7NodeTimerT21 | 0 | 0 | The Timer T21 is started when initial group blocking message is sent. The valid values are 60 seconds for ANSI and 300 to 900 se… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.42 | sonusSs7NodeTimerT22 | 0 | 0 | The Timer T22 is started when circuit group reset message is sent. The valid values are 4 to 15 seconds for ANSI and 15 to 60 se… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.43 | sonusSs7NodeTimerT23 | 0 | 0 | The Timer T23 is started when initial group reset message is sent. The valid values are 60 seconds for the ANSI and 300 to 900 s… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.44 | sonusSs7NodeTimerT24 | 0 | 0 | The Timer T24 is started when check tone is sent. The value is less than 2 seconds. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.45 | sonusSs7NodeTimerT25 | 0 | 0 | The Timer T25 is started when initial continuity check failure is detected. The range is 1 to 10 seconds. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.46 | sonusSs7NodeTimerT26 | 0 | 0 | The Timer T26 is started when a second or subsequent continuity failure is detected. The valid value are 60 to 180 seconds. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.47 | sonusSs7NodeTimerT27 | 0 | 0 | The Timer T27 is started when a continuity fail message is recieved. The valid values are more than 180 seconds for ANSI and 240… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.48 | sonusSs7NodeTimerT28 | 0 | 0 | The Timer T28 is started when Circuit Query Message is sent. The valid value is 10 seconds. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.49 | sonusSs7NodeTimerT29 | 0 | 0 | The Timer T29 is started when Congestion indication is received when T29 is not running. The valid range is 300 to 600 milli sec… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.50 | sonusSs7NodeTimerT30 | 0 | 0 | The Timer T30 is stared when congestion indication is recieved when T29 is not running. The valid range is 5 to 10 seconds for t… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.51 | sonusSs7NodeTimerT31 | 0 | 0 | The Timer T31 is started on release of ISUP signalling connection based on CO SCCP. The value should be set to greater than 360 … |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.52 | sonusSs7NodeTimerT32 | 0 | 0 | The Timer T32 is started when the first end-to-end message is recived. Under ANSI this timer is started after the response to su… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.53 | sonusSs7NodeTimerT33 | 0 | 0 | The Timer T33 is started when Information Request Message is sent. The valid range is 12 to 15 seconds. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.54 | sonusSs7NodeTimerT34 | 0 | 0 | The Timer T34 is started when Loop Back Acknowledgement is sent under ANSI. The Timer T34 is started when segmentation is receiv… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.55 | sonusSs7NodeTimerT35 | 0 | 0 | The Timer T35 is started when the last digit recieved is not an ST digit or the fixed number of digits have been recieved. This … |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.56 | sonusSs7NodeTimerT36 | 0 | 0 | The Timer T36 is started when IAM is recived with a segmentation indication for ANSI. This timer is started when transit or inco… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.57 | sonusSs7NodeTimerT37 | 0 | 0 | The Timer T37 is started when User Part Availability test is started under ANSI. This timer is started when a request for and Ec… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.58 | sonusSs7NodeTimerT38 | 0 | 0 | The Timer T38 is started when a suspend message is sent to the preceding switch. This timer is only relevent under ITU. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.59 | sonusSs7NodeTimerT39 | 0 | 0 | The Timer T39 is started when MCID request is sent. It is only relevent in the ITU. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.60 | sonusSs7NodeTimerT40 | 0 | 0 | The Timer T40 could be changed from its default using this entry. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.61 | sonusSs7NodeTimerTAcc | 0 | 0 | Automatic Congestion Control Timer as per ANSI T1.113.4 - 1995. The value of the timer is 5 Seconds. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.62 | sonusSs7NodeTimerTCcr | 0 | 0 | Continuity Check Request Timer. The value As per ANSI T1.113.4 - 1995 is 2 Seconds. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.63 | sonusSs7NodeTimerTCcrr | 0 | 0 | Continuity Check Failed Recived. The value as per ANSI T1.113.4 - 1995 is 20 Seconds. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.64 | sonusSs7NodeTimerTCgb | 0 | 0 | Timer started on recipt of a Circuit Group Block Message. The value as per ANSI T1.113.4 - 1995 is 5 Seconds. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.65 | sonusSs7NodeTimerTCra | 0 | 0 | Timer started when Circuit Reservation Acknowledgment is sent. The time value as per ANSI T1.113.4 - 1995 is 20 seconds. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.66 | sonusSs7NodeTimerTCrm | 0 | 0 | This timer is started when the circuit reservation message is sent. The value as per ANSI T1.113.4 - 1995 is 3 - 4 Seconds. The … |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.67 | sonusSs7NodeTimerTCvt | 0 | 0 | The Timer T CVT is started when the Circuit Validation Test message is sent. This message is only valid for ANSI. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.68 | sonusSs7NodeTimerTExm | 0 | 0 | The Timer Exm,d is started when IAM is sent to the succeeding network. This timer has no relevence in the ITU. This timer is in … |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.69 | sonusSs7NodeTimerTGrs | 0 | 0 | This timer is started when a circuit group reset message is received. This timer is only relevent in the ANSI network. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.70 | sonusSs7NodeTimerTHga | 0 | 0 | This timer is started on recognition of carrier loss. It is only relevent in ANSI network. The valid range is 0 to 300 seconds. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.71 | sonusSs7NodeTimerTScga | 0 | 0 | This timer is started when initial demand continuity check fails in the SCGA group. The valid range for this timer is 0 to 120 s… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.72 | sonusSs7NodeTimerTScgad | 0 | 0 | This timer is started failure of demand continuity check in the SCGA group. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.73 | sonusSs7NodeApplProfileName | 0 | 0 | The SS7 Node Profile to be applied to the node. The values here are a snap shot only and might have changed since they were set. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.74 | sonusSs7NodeNetworkInd | 0 | 0 | The setting of the Network Indicator used for this SS7 Node entry. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.75 | sonusSs7NodeSlsBits | 0 | 0 | The number of SLS bits to use |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.76 | sonusSs7NodeTimerTA | 0 | 0 | The Bellcore specific timer TA is the guard timer on outgoing SS7 circuit before idling. The value of this timer is 0 to 1000 mi… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.77 | sonusSs7NodeTimerTBlom | 0 | 0 | The Bellcore specific timer TBlom is started when blocking a circuit due to a BLO, and after any call is released; used to notif… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.78 | sonusSs7NodeTimerTCotd | 0 | 0 | The Bellcore specific timer TCOTd is started when sending IAM requesting continuity check. The value of this timer is in millise… |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.79 | sonusSs7NodeTimerTCotl | 0 | 0 | The Bellcore specific timer TCOTl is started when receiving second COT coded failed, awaiting receipt of CCR. |
| 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.80 | sonusSs7NodeTimerTSus | 0 | 0 | The Bellcore specific timer TSUS is started when a SUS message is sent by the terminating switch, awaiting called party off-hook… |