This variable indicates the Line Status of the interface. A
similar object is defined in the rfc1406 configuration table as
dsx1LineStatus. The variable contains loopback state
information and failure state information. It is a bit map
represented as a sum. The ds1NoAlarm should be set if and only
if no other flag is set.
The various bit positions are:
1 No Alarm.
2 Receiving PLCP Yellow Alarm Indication.
4 Transmitting PLCP Yellow alarm indication.
8 Receiving PLCP LOF.
16 Receiving DS1 Yellow Alarm Indication.
32 Transmiting DS1 Yellow Alarm Indication.
64 Receiving AIS failure indication.
128 Receiving LOF failure indication.
256 Receiving LOS failure indication.
512 Loopback State.
1024 Receiving a test pattern.
2048 Other failures.
4096 Receiving Excessive CRC Errors.
32768 Receiving LCD failure indication.
Parsed from file fore-ds1.mib.txt
Company: None
Module: Fore-DS1-MIB
This variable indicates the Line Status of the interface. A
similar object is defined in the rfc1406 configuration table as
dsx1LineStatus. The variable contains loopback state
information and failure state information. It is a bit map
represented as a sum. The ds1NoAlarm should be set if and only
if no other flag is set.
The various bit positions are:
1 No Alarm.
2 Receiving PLCP Yellow Alarm Indication.
4 Transmitting PLCP Yellow alarm indication.
8 Receiving PLCP LOF.
16 Receiving DS1 Yellow Alarm Indication.
32 Transmiting DS1 Yellow Alarm Indication.
64 Receiving AIS failure indication.
128 Receiving LOF failure indication.
256 Receiving LOS failure indication.
512 Loopback State.
1024 Receiving a test pattern.
2048 Other failures.
4096 Receiving Excessive CRC Errors.
32768 Receiving LCD failure indication.
Parsed from file Fore-DS1-MIB.mib
Module: Fore-DS1-MIB
Vendor: Fore Systems, Inc.
Module: Fore-DS1-MIB
[Automatically extracted from oidview.com]
ds1LineStatus OBJECT-TYPE SYNTAX Integer32 (1..65534) MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the Line Status of the interface. A similar object is defined in the rfc1406 configuration table as dsx1LineStatus. The variable contains loopback state information and failure state information. It is a bit map represented as a sum. The ds1NoAlarm should be set if and only if no other flag is set. The various bit positions are: 1 No Alarm. 2 Receiving PLCP Yellow Alarm Indication. 4 Transmitting PLCP Yellow alarm indication. 8 Receiving PLCP LOF. 16 Receiving DS1 Yellow Alarm Indication. 32 Transmiting DS1 Yellow Alarm Indication. 64 Receiving AIS failure indication. 128 Receiving LOF failure indication. 256 Receiving LOS failure indication. 512 Loopback State. 1024 Receiving a test pattern. 2048 Other failures. 4096 Receiving Excessive CRC Errors. 32768 Receiving LCD failure indication." ::= { ds1ConfEntry 12 }
ds1LineStatus OBJECT-TYPE SYNTAX Integer32 (1..65534) MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the Line Status of the interface. A similar object is defined in the rfc1406 configuration table as dsx1LineStatus. The variable contains loopback state information and failure state information. It is a bit map represented as a sum. The ds1NoAlarm should be set if and only if no other flag is set. The various bit positions are: 1 No Alarm. 2 Receiving PLCP Yellow Alarm Indication. 4 Transmitting PLCP Yellow alarm indication. 8 Receiving PLCP LOF. 16 Receiving DS1 Yellow Alarm Indication. 32 Transmiting DS1 Yellow Alarm Indication. 64 Receiving AIS failure indication. 128 Receiving LOF failure indication. 256 Receiving LOS failure indication. 512 Loopback State. 1024 Receiving a test pattern. 2048 Other failures. 4096 Receiving Excessive CRC Errors. 32768 Receiving LCD failure indication." ::= { ds1ConfEntry 12 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.326.2.2.1.1.7.1.1.1.1 | ds1ConfBoard | 0 | 0 | The index of this port's switch board. |
| 1.3.6.1.4.1.326.2.2.1.1.7.1.1.1.2 | ds1ConfModule | 0 | 0 | The network module of this port. |
| 1.3.6.1.4.1.326.2.2.1.1.7.1.1.1.3 | ds1ConfPort | 0 | 0 | The number of this port. |
| 1.3.6.1.4.1.326.2.2.1.1.7.1.1.1.4 | ds1LineType | 0 | 0 | This variable indicates the variety of DS1 Line implementing this circuit. The type of circuit affects the number of bits per sec… |
| 1.3.6.1.4.1.326.2.2.1.1.7.1.1.1.5 | ds1LineCoding | 0 | 0 | This variable describes the variety of Zero Code suppression used on this link, which in turn affects a number of its characteris… |
| 1.3.6.1.4.1.326.2.2.1.1.7.1.1.1.6 | ds1SendCode | 0 | 0 | This variable indicates what type of code is being sent across the DS1 interface by the device. The values mean: ds1SendNoCode se… |
| 1.3.6.1.4.1.326.2.2.1.1.7.1.1.1.7 | ds1ReceiveCode | 0 | 0 | This variable indicates the type of code that was received across the DS interface. The values mean: ds1ReceiveNoCode receiving lo… |
| 1.3.6.1.4.1.326.2.2.1.1.7.1.1.1.8 | ds1LoopbackConfig | 0 | 0 | This variable represents the loopback configuration of the DS1 interface. This variable is defined in the rfc1406 configuration t… |
| 1.3.6.1.4.1.326.2.2.1.1.7.1.1.1.9 | ds1TxClockSource | 0 | 0 | The source of the transmit clock. rxTiming(1) indicated that the recovered receive clock is used as the transmit clock. localTimin… |
| 1.3.6.1.4.1.326.2.2.1.1.7.1.1.1.13 | ds1IdleUnassignedCells | 0 | 0 | This variable indicates the types of cells that should be sent in case there is no real data to send. According to the ATM Forum,… |
| 1.3.6.1.4.1.326.2.2.1.1.7.1.1.1.14 | ds1LineTypeFraming | 0 | 0 | This variable indicates the way ATM cells are constructed from the DS1 stream. ds1Hcs(2) indicates that the ATM cells are constru… |
| 1.3.6.1.4.1.326.2.2.1.1.7.1.1.1.15 | ds1LineLength | 0 | 0 | This variable represents the length of the physical cable connected to the ds1 port. The user has to set this object to match the… |
| 1.3.6.1.4.1.326.2.2.1.1.7.1.1.1.16 | ds1RxScrambling | 0 | 0 | This variable indicates whether the information is being descrambled on receiving. It should be set the same as the transmitting … |
| 1.3.6.1.4.1.326.2.2.1.1.7.1.1.1.17 | ds1TxScrambling | 0 | 0 | This variable indicates whether the information (48 octet payload) is being scrambled before transmitting. It should be set the s… |
| 1.3.6.1.4.1.326.2.2.1.1.7.1.1.1.18 | ds1TxPRBS | 0 | 0 | This variable controls the Pseudo-Random Bit Sequence Generator (PRSG) which generates an unframed 2^15-1 test sequence as define… |
| 1.3.6.1.4.1.326.2.2.1.1.7.1.1.1.19 | ds1CRCErrThrSeconds | 0 | 0 | This variable represents the consecutive number of BAD/GOOD seconds to detect/clear an Excessive CRC Error Defect. The range of v… |
| 1.3.6.1.4.1.326.2.2.1.1.7.1.1.1.20 | ds1CRCErrThrErrors | 0 | 0 | This variable is a threshold for the number of CRC Errors per second and is used as a parameter to the Excessive CRC Error Defect… |
| 1.3.6.1.4.1.326.2.2.1.1.7.1.1.1.21 | ds1CRCErrFailEnable | 0 | 0 | This variable controls whether declaration of an Excessive CRC Error Defect forces the port's operState to Down. |
| 1.3.6.1.4.1.326.2.2.1.1.7.1.1.1.22 | ds1SigFailBer | 0 | 0 | This is the exponent of 10 for the current signal fail bit error rate (BER) threshold for this port. The value -4, for example, r… |
| 1.3.6.1.4.1.326.2.2.1.1.7.1.1.1.23 | ds1SigDegradeBer | 0 | 0 | This is the exponent of 10 for the current signal degrade bit error rate (BER) threshold for this port. The value -8, for example… |
| 1.3.6.1.4.1.326.2.2.1.1.7.1.1.1.24 | ds1BerErrorModel | 0 | 0 | This is the error distribution model to be used to identify signal degrade and signal fail conditions. errorModelRandom selects a… |
| 1.3.6.1.4.1.326.2.2.1.1.7.1.1.1.25 | ds1BerState | 0 | 0 | This value describes the current state of the port as determined through bit error rate analysis. |