Setting this object to local(2) will add all negotiated
PPP ip addresses as host routes to the ip routing table.
Setting this object to global(3) adds the same ip addresses
to the ip routing table as well as exporting these host
routes through enabled routing protocols.
Parsed from file it-router-12.mib.txt
Company: inreach
Module: IT-ROUTER-12
xCircPartnerIpAdv OBJECT-TYPE SYNTAX INTEGER { disabled(1), local(2), global(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Setting this object to local(2) will add all negotiated PPP ip addresses as host routes to the ip routing table. Setting this object to global(3) adds the same ip addresses to the ip routing table as well as exporting these host routes through enabled routing protocols." DEFVAL { disabled } ::= { xCircuitAdmnEntry 37 }
Vendor: In-Reach
Module: IT-ROUTER-12 (it-router-12.mib)
Type: TABULAR
Access: read-write
Syntax: INTEGER
Automatically extracted from www.mibdepot.com
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.33.24.5.1.1.1 | xCircAdminIf | 0 | 0 | The ifIndex of the iTouch interface to which this circuit is attached. The value may be 0 for default circuits which indicates t… |
| 1.3.6.1.4.1.33.24.5.1.1.2 | xCircCallType | 0 | 0 | The type of link on which this circuit can be used. This field is not modifiable for default circuits. The value 0 is for no ca… |
| 1.3.6.1.4.1.33.24.5.1.1.3 | xCircCallWhen | 0 | 0 | Controls when the circuit will be dialed by the system. |
| 1.3.6.1.4.1.33.24.5.1.1.4 | xCircAdminProtocol | 0 | 0 | Controls the encapsulation and feature negotiation to be used on this circuit. The value auto may only be set on default circuit… |
| 1.3.6.1.4.1.33.24.5.1.1.5 | xCircDialback | 0 | 0 | Controls when the circuit will dial back the caller when a call is received on this circuit. |
| 1.3.6.1.4.1.33.24.5.1.1.6 | xCircMaxForwardDelay | 0 | 0 | The number of milliseconds that a packet may be held on the Wan link before it will be discarded. The value 0 indicates no limit. |
| 1.3.6.1.4.1.33.24.5.1.1.7 | xCircMaxMultiForwardDelay | 0 | 0 | The number of milliseconds that a multicast packet may be held on the Wan link before it will be discarded. The value 0 indicat… |
| 1.3.6.1.4.1.33.24.5.1.1.8 | xCircProtocolBaseTimer | 0 | 0 | Controls how often the protocol sends out its maintenance messages and subsequently how fast the circuit can detect when it goes … |
| 1.3.6.1.4.1.33.24.5.1.1.9 | xCircAdminSpeed | 0 | 0 | The speed that the software should use for the circuit The value 0 indicates that the speed inherited from the link should be use… |
| 1.3.6.1.4.1.33.24.5.1.1.10 | xCircConnectTimer | 0 | 0 | The number of seconds to wait for the circuit protocol to believe the circuit has come up after answering a call or establishing … |
| 1.3.6.1.4.1.33.24.5.1.1.11 | xCircIdleTimer | 0 | 0 | The number of seconds to wait for the circuit without sending or receiving a data packet before bringing down the circuit if it w… |
| 1.3.6.1.4.1.33.24.5.1.1.12 | xCircRestartTimer | 0 | 0 | If this circuit failed to be dialed, the system will wait this time after failing to establish the call retry count timers before… |
| 1.3.6.1.4.1.33.24.5.1.1.13 | xCircRetryCount | 0 | 0 | The number of times the circuit will be retried for dialing before it goes into the restart waiting state. |
| 1.3.6.1.4.1.33.24.5.1.1.14 | xCircRetryTimer | 0 | 0 | If this circuit failed to be dialed, the system will wait this time before retrying to dial the circuit. |
| 1.3.6.1.4.1.33.24.5.1.1.15 | xCircAnswerPriority | 0 | 0 | The priority of a call answered on this circuit. |
| 1.3.6.1.4.1.33.24.5.1.1.16 | xCircIfDialPriority | 0 | 0 | The priority of a call dialed on this circuit because the circuit is dial always or dial on demand. |
| 1.3.6.1.4.1.33.24.5.1.1.17 | xCircMaxConnectTime | 0 | 0 | The maximum number of seconds for which a call answered on this circuit may be active. The value 0 indicates indefinitely. |
| 1.3.6.1.4.1.33.24.5.1.1.18 | xCircPartnerBridgeOnly | 0 | 0 | The maximum number of seconds for which a call answered on this circuit may be active. The value 0 indicates indefinitely. |
| 1.3.6.1.4.1.33.24.5.1.1.19 | xCircDialConnectTimer | 0 | 0 | The number of seconds to wait for a call to be brought up or answered. This is used by only circuits of some xCircCallTypes. A v… |
| 1.3.6.1.4.1.33.24.5.1.1.20 | xCircTimeRemaining | 0 | 0 | The time remaining for the circuit when it is active before it will be disconnected. Setting this value will reset how many seco… |
| 1.3.6.1.4.1.33.24.5.1.1.21 | xCircDialLink | 0 | 0 | A bitmap of the links on which this circuit can be used. This can only be written for link based circuits. |
| 1.3.6.1.4.1.33.24.5.1.1.22 | xCircDodMaxQueueSize | 0 | 0 | Controls the number of packets that will be held while trying to bring up a demand circuit. |
| 1.3.6.1.4.1.33.24.5.1.1.23 | xCircAdminState | 0 | 0 | Controls whether the circuit can be used. |
| 1.3.6.1.4.1.33.24.5.1.1.24 | xCircPartnerEthAddress | 0 | 0 | The assumed ethernet address of the circuit's partner. This is only used for end system partners who dial in and request an ether… |
| 1.3.6.1.4.1.33.24.5.1.1.25 | xCircPartnerIpAddress | 0 | 0 | The assumed IP address of the circuit's partner. This is only used for end system partners who dial in and request an IP address … |
| 1.3.6.1.4.1.33.24.5.1.1.26 | xCircEventLogging | 0 | 0 | Controls whether events will be logged for this circuit. |
| 1.3.6.1.4.1.33.24.5.1.1.27 | xCircRowStatus | 0 | 0 | Setting this object to active(1) activates the circuit. This is equivalent to creating the circuit. Setting this object to notInS… |
| 1.3.6.1.4.1.33.24.5.1.1.28 | xCircTimeMaxOutputQueueSize | 0 | 0 | The size of the output queue. |
| 1.3.6.1.4.1.33.24.5.1.1.29 | xCircDodDemandDelayTime | 0 | 0 | Controls the amount of time a demand circuit will wait after connecting to its partner before sending packets contained in the ci… |
| 1.3.6.1.4.1.33.24.5.1.1.30 | xCircSameAs | 0 | 0 | This object allows the user to clone a circuit from another circuit. It is the equivalent of the User interface command define ci… |
| 1.3.6.1.4.1.33.24.5.1.1.31 | xCircDialPeriodicTime | 0 | 0 | The number of minutes for the period. If during this period, the maximum periodic dial attempts of connect time is exceeded, the… |
| 1.3.6.1.4.1.33.24.5.1.1.32 | xCircDialTrapThreshold | 0 | 0 | The threshold that an SNMP trap will be generated warning that the circuit may be either disabled or temporarily prohibited from … |
| 1.3.6.1.4.1.33.24.5.1.1.33 | xCircMaxDialTime | 0 | 0 | The maximum number of minutes before a dialed call will be disconnected and the circuit will be disabled. The administrator will … |
| 1.3.6.1.4.1.33.24.5.1.1.34 | xCircMaxAnswerTime | 0 | 0 | The maximum number of minutes before an answered call will be disconneted. The value 0 indicates there is no limit. |
| 1.3.6.1.4.1.33.24.5.1.1.35 | xCircMaxPeriodicDialAttempt | 0 | 0 | The maximum number of times this circuit can be dialed during the periodic time before it will be prohibited from dialing. The c… |
| 1.3.6.1.4.1.33.24.5.1.1.36 | xCircMaxPeriodicDialTime | 0 | 0 | The maximum number of minutes before a dialed call will be disconnected and the circuit will be prohibited from dialing. The cir… |
| 1.3.6.1.4.1.33.24.5.1.1.38 | xCircQuerytimeNegotiate | 0 | 0 | Setting this object to enabled(2) causes the circuit to be dialed automatically after a reboot if the unit does not have a batter… |
| 1.3.6.1.4.1.33.24.5.1.1.39 | xCircPartnerType | 0 | 0 | This object defines the partner type associated with this circuit. |
| 1.3.6.1.4.1.33.24.5.1.1.40 | xCircPacing | 0 | 0 | This object defines the circuit pacing method for this circuit. Disabled(1) implies no pacing, limited means that the throughput… |
| 1.3.6.1.4.1.33.24.5.1.1.41 | xCircCfgThroughput | 0 | 0 | This object defines throughput value for a circuit which is used by pacing when the xCircPacing object is set to limited. |
| 1.3.6.1.4.1.33.24.5.1.1.42 | xCircPrQueState | 0 | 0 | This object defines whether or not priority queuing is enabled. The xCircPacing must be set to something other than disabled if p… |