Type of vt framing format. Is applicable
only in byte-sync mapping mode for T1 tributaries.
notApplicable: if VT mapping is not byte-sync.
sf: superframe format.
esf: extended superframe format.
Default is esf if sonetTributaryMappingType is set to
byteSynchronous, else the default is notApplicable.
Parsed from file CISCO-MGX82XX-SONET-MIB.mib
Module: CISCO-MGX82XX-SONET-MIB
Vendor: Stratacom
Module: CISCO-MGX82XX-SONET-MIB
[Automatically extracted from oidview.com]
sonetTributaryFramingFormat OBJECT-TYPE SYNTAX INTEGER { notApplicable(1), sf(2), esf(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Type of vt framing format. Is applicable only in byte-sync mapping mode for T1 tributaries. notApplicable: if VT mapping is not byte-sync. sf: superframe format. esf: extended superframe format. Default is esf if sonetTributaryMappingType is set to byteSynchronous, else the default is notApplicable. " ::= { sonetConfigEntry 13 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.1 | sonetLineNum | 0 | 0 | This object is the identifier of a SONET Interface on a managed device. For MGX8850(For example PXM1 Module): OC-3 : sonetLineNum … |
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.2 | sonetLineType | 0 | 0 | This variable indicates the cell framing. Defaults to Sts-3c |
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.3 | sonetLineLoopbackCommand | 0 | 0 | This variable represents the loopback configuration of the SONET interface. The values mean: sonetNoLoop Not in the loopback state.… |
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.4 | sonetHCSmasking | 0 | 0 | HCS masking. Defaults to enable. |
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.5 | sonetPayloadScrambling | 0 | 0 | STS3c or STM-1 payload scrambling. Defaults to enable. |
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.6 | sonetFrameScrambling | 0 | 0 | STS3c or STM-1 frame scrambling. Defaults to enable. |
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.7 | sonetLineEnable | 0 | 0 | This variable indicates if the line is enabled or not defaults to disable |
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.8 | sonetLineXmtClkSrc | 0 | 0 | This represents the type of transmit clock source. backplaneClk: clock source is from the controller card, transmitted via the ba… |
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.9 | sonetRDIVType | 0 | 0 | This variable represents the type of RDI-V sent by this NE to remote NE. onebit: use 1 bit RDI-V. Compatible with older equipment… |
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.10 | sonetRDIPType | 0 | 0 | This variable represents the type of RDI-P sent by this NE to remote NE. onebit: use 1 bit RDI-P. Compatible with older equipment… |
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.11 | sonetTributaryType | 0 | 0 | Type of tributary carried within the Sonet/Sdh signal. vt15vc11: carries T1 signals (VT15 or VC11) vt2vc12: carries E1 signals (V… |
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.12 | sonetTributaryMappingType | 0 | 0 | Type of VT/VC mapping. asynchronous: In this mode, the channel structure of the DS1/E1 is neither visible nor preserved. byteSynch… |
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.14 | sonetSignallingTransportMode | 0 | 0 | The mode used to transport DS0 signalling information for T1 byte-sync mapping. notApplicable: if byte-sync mapping is not used. s… |
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.15 | sonetTributaryGroupingType | 0 | 0 | This variable indicates the method used to group VCs into an STM-1 signal. Applicable only to SDH. notApplicable: for sonet inter… |