The mode used to transport DS0 signalling
information for T1 byte-sync mapping.
notApplicable: if byte-sync mapping is not used.
signallingTransferMode: the robbed bit signalling
is transferred into the S bits of the VT header
and framing bit is discarded.
clearMode: only the framing bit is transferred to
VT header. The signalling bits are left intact
in the VT payload.
Default is signallingTransferMode if sonetTributaryMappingType
is set to byteSynchronous, else the default is notApplicable.
Parsed from file CISCO-MGX82XX-SONET-MIB.mib
Module: CISCO-MGX82XX-SONET-MIB
Vendor: Stratacom
Module: CISCO-MGX82XX-SONET-MIB
[Automatically extracted from oidview.com]
sonetSignallingTransportMode OBJECT-TYPE SYNTAX INTEGER { notApplicable(1), signallingTransferMode(2), clearMode(3) } ACCESS read-write STATUS mandatory DESCRIPTION "The mode used to transport DS0 signalling information for T1 byte-sync mapping. notApplicable: if byte-sync mapping is not used. signallingTransferMode: the robbed bit signalling is transferred into the S bits of the VT header and framing bit is discarded. clearMode: only the framing bit is transferred to VT header. The signalling bits are left intact in the VT payload. Default is signallingTransferMode if sonetTributaryMappingType is set to byteSynchronous, else the default is notApplicable. " ::= { sonetConfigEntry 14 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.1 | sonetLineNum | 0 | 0 | This object is the identifier of a SONET Interface on a managed device. For MGX8850(For example PXM1 Module): OC-3 : sonetLineNum … |
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.2 | sonetLineType | 0 | 0 | This variable indicates the cell framing. Defaults to Sts-3c |
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.3 | sonetLineLoopbackCommand | 0 | 0 | This variable represents the loopback configuration of the SONET interface. The values mean: sonetNoLoop Not in the loopback state.… |
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.4 | sonetHCSmasking | 0 | 0 | HCS masking. Defaults to enable. |
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.5 | sonetPayloadScrambling | 0 | 0 | STS3c or STM-1 payload scrambling. Defaults to enable. |
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.6 | sonetFrameScrambling | 0 | 0 | STS3c or STM-1 frame scrambling. Defaults to enable. |
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.7 | sonetLineEnable | 0 | 0 | This variable indicates if the line is enabled or not defaults to disable |
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.8 | sonetLineXmtClkSrc | 0 | 0 | This represents the type of transmit clock source. backplaneClk: clock source is from the controller card, transmitted via the ba… |
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.9 | sonetRDIVType | 0 | 0 | This variable represents the type of RDI-V sent by this NE to remote NE. onebit: use 1 bit RDI-V. Compatible with older equipment… |
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.10 | sonetRDIPType | 0 | 0 | This variable represents the type of RDI-P sent by this NE to remote NE. onebit: use 1 bit RDI-P. Compatible with older equipment… |
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.11 | sonetTributaryType | 0 | 0 | Type of tributary carried within the Sonet/Sdh signal. vt15vc11: carries T1 signals (VT15 or VC11) vt2vc12: carries E1 signals (V… |
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.12 | sonetTributaryMappingType | 0 | 0 | Type of VT/VC mapping. asynchronous: In this mode, the channel structure of the DS1/E1 is neither visible nor preserved. byteSynch… |
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.13 | sonetTributaryFramingFormat | 0 | 0 | Type of vt framing format. Is applicable only in byte-sync mapping mode for T1 tributaries. notApplicable: if VT mapping is not b… |
| 1.3.6.1.4.1.351.110.4.6.1.1.1.1.15 | sonetTributaryGroupingType | 0 | 0 | This variable indicates the method used to group VCs into an STM-1 signal. Applicable only to SDH. notApplicable: for sonet inter… |