This object is used to configure the switching direction
which this APS line support. Unidirectional switch only one
direction. Bidirectional switch in both ends of the line.
Parsed from file CISCO-MGX82XX-SONET-MIB.mib
Module: CISCO-MGX82XX-SONET-MIB
Vendor: Stratacom
Module: CISCO-MGX82XX-SONET-MIB
[Automatically extracted from oidview.com]
apsdirection OBJECT-TYPE SYNTAX INTEGER { uniDirectional (1), biDirectional (2) } ACCESS read-write STATUS mandatory DESCRIPTION "This object is used to configure the switching direction which this APS line support. Unidirectional switch only one direction. Bidirectional switch in both ends of the line. " ::= { sonetApsConfigEntry 11 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.351.110.4.6.1.6.1.1.1 | apsWorkingSlot | 0 | 0 | This object is the chassis slot number of the working line MGX 8x50 PXM: can only be slot 7 or 8. MGX 8x30 PXM: can only be slot … |
1.3.6.1.4.1.351.110.4.6.1.6.1.1.2 | apsWorkingLine | 0 | 0 | This object is the line number of the working line OC-3 : sonetLineNum in a range 1..4 OC-12: sonetLineNum = 1 is the ONLY valid … |
1.3.6.1.4.1.351.110.4.6.1.6.1.1.3 | apsProtectionSlot | 0 | 0 | This object is the chassis slot number of the protection line MGX 8x50 PXM: can only be slot 7 or 8. MGX 8x30 PXM: can only be sl… |
1.3.6.1.4.1.351.110.4.6.1.6.1.1.4 | apsProtectionLine | 0 | 0 | This object is the line number of the working line OC-3 : sonetLineNum in a range 1..4 OC-12: sonetLineNum = 1 is the ONLY valid … |
1.3.6.1.4.1.351.110.4.6.1.6.1.1.5 | apsEnable | 0 | 0 | This object is used to enable or disable APS feature on the working/protection line pairs. |
1.3.6.1.4.1.351.110.4.6.1.6.1.1.6 | apsArchMode | 0 | 0 | This object is used to configure APS architecture mode on the working/protection line pairs. The architecture modes currently sup… |
1.3.6.1.4.1.351.110.4.6.1.6.1.1.7 | apsActiveLine | 0 | 0 | This object indicates which line is currently active ob the trunk line. |
1.3.6.1.4.1.351.110.4.6.1.6.1.1.8 | apsSFBER | 0 | 0 | This object contains the Bit Error Rate threshold for Signal Fault detection on the working line. |
1.3.6.1.4.1.351.110.4.6.1.6.1.1.9 | apsSDBER | 0 | 0 | This object contains the Bit Error Rate threshold for Signal Degrade detection on the working line. If set to 5, it means SDBER r… |
1.3.6.1.4.1.351.110.4.6.1.6.1.1.10 | apsWtr | 0 | 0 | This object contains interval (in minute) to wait before attempting to switch back to working line. Not applicable if the line co… |
1.3.6.1.4.1.351.110.4.6.1.6.1.1.12 | apsRevertive | 0 | 0 | This object is used to configure the APS revertive or nonrevertive option. Revertive allows the line to be switch back to workin… |
1.3.6.1.4.1.351.110.4.6.1.6.1.1.13 | apsK1K2Disable | 0 | 0 | This object is used to enable or disable the K1/K2 inband interface on the protection line. |