This is the Spinup Delay for Spinning Up Physical Drives
at Firmware Initialization Time. The Physical Drives are
divided into Groups, each containing the number of drives
indicated by the spinupCount variable. spinupDelay
variable is the amount of delay used before the drives in
the next group are issued a SPINUP Command.
Parsed from file RAID-Adapter-MIB.mib
Module: RAID-Adapter-MIB
Vendor: Dell
Module: RAID-Adapter-MIB (Perc.mib)
Type: TABULAR
Access: read-only
Syntax: INTEGER
Automatically extracted from www.mibdepot.com
spinupDelay OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional DESCRIPTION "This is the Spinup Delay for Spinning Up Physical Drives at Firmware Initialization Time. The Physical Drives are divided into Groups, each containing the number of drives indicated by the spinupCount variable. spinupDelay variable is the amount of delay used before the drives in the next group are issued a SPINUP Command." ::= { adapterEntry 9 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.3582.1.1.1.1.1 | adpAdapterNumber | 0 | 0 | The Adapter Number for this Instance of Adapter Object. This Entry in the Table, contains Information about the Adapter Number sp… |
| 1.3.6.1.4.1.3582.1.1.1.1.2 | numLogicalDrives | 0 | 0 | Number of Logical Drives Configured on this Adapter. |
| 1.3.6.1.4.1.3582.1.1.1.1.3 | firmwareVersion | 0 | 0 | The Firmware Version of the Firmware running on this Adapter. |
| 1.3.6.1.4.1.3582.1.1.1.1.4 | biosVersion | 0 | 0 | The Bios Version of the BIOS Present in the Flash ROM on this Adapter. |
| 1.3.6.1.4.1.3582.1.1.1.1.5 | dramSizeInMB | 0 | 0 | Amount of DRAM in Mega Bytes present on this Adapter. |
| 1.3.6.1.4.1.3582.1.1.1.1.6 | chipSetType, rebuildRateInPercent | 0 | 0 | Rebuild Rate for this Adapter. This determines the Priority of Rebuild/Check-Consistency/Reconstruct Operations versus the Read-W… |
| 1.3.6.1.4.1.3582.1.1.1.1.7 | rebuildRateInPercent, flushInterval | 0 | 0 | Internal Cache Flush Interval for Logical Drives in WriteBack Mode. |
| 1.3.6.1.4.1.3582.1.1.1.1.8 | flushInterval, maxConcurrentCmds | 0 | 0 | Maximum Concurrent Commands Supported by the Adapter. |
| 1.3.6.1.4.1.3582.1.1.1.1.10 | spinupDelay, spinupCount | 0 | 0 | This is the Spinup Count for Spinning up Physical Drives at Firmware Initialization Time. The Physical Drives are divided into Gr… |
| 1.3.6.1.4.1.3582.1.1.1.1.11 | spinupCount, adpIOReadsPerSec | 0 | 0 | Number of IO Reads/sec statistics for this adapter. |
| 1.3.6.1.4.1.3582.1.1.1.1.12 | adpIOReadsPerSec, adpIOWritesPerSec | 0 | 0 | Number of IO Writes/sec statistics for this adapter. |
| 1.3.6.1.4.1.3582.1.1.1.1.13 | adpIOWritesPerSec, adpReadKBsPerSec | 0 | 0 | Amount of Data Transferred in KBs/sec due to READ Transfers. |
| 1.3.6.1.4.1.3582.1.1.1.1.14 | adpReadKBsPerSec, adpWriteKBsPerSec | 0 | 0 | Amount of Data Transferred in KBs/sec due to WRITE Transfers. |
| 1.3.6.1.4.1.3582.1.1.1.1.15 | adpWriteKBsPerSec, adpReadFailuresPerSec | 0 | 0 | Number of Read-Failures/sec statistics for this adapter. |
| 1.3.6.1.4.1.3582.1.1.1.1.16 | adpReadFailuresPerSec, adpWriteFailuresPerSec | 0 | 0 | Number of Write-Failures/sec statistics for this adapter. |
| 1.3.6.1.4.1.3582.1.1.1.1.17 | adpWriteFailuresPerSec, scanChannels | 0 | 0 | Use this Variable to Discover the Non-Disk Devices attached to the Adapter. Set this Variable to startscan (an integer value of 2… |
| 1.3.6.1.4.1.3582.1.1.1.1.18 | scanChannels, adpBasePort | 0 | 0 | Maximum Concurrent Commands Supported by the Adapter. |
| 1.3.6.1.4.1.3582.1.1.1.1.19 | numSCSIChannels | 0 | 0 | Maximum number of SCSI Channels Supported by the Adapter. |
| 1.3.6.1.4.1.3582.1.1.1.1.20 | numFCLoops | 0 | 0 | Number of Fibre channel loops Supported by the Adapter. |
| 1.3.6.1.4.1.3582.1.1.1.1.21 | subSystemID | 0 | 0 | The PCI sub system ID of this controller |
| 1.3.6.1.4.1.3582.1.1.1.1.22 | subSystemVendorID | 0 | 0 | The PCI sub system vendor ID of this controller |
| 1.3.6.1.4.1.3582.1.1.1.1.23 | productName | 0 | 0 | The enriched formation of the controller retrieved from the firmware |
| 1.3.6.1.4.1.3582.1.1.1.1.24 | adpSpeed | 0 | 0 | Maximum transfer speed of the adapter. |